Consider the removal of soil particles in a settling basin. The particles have a density of 1.3 g /cm3. The diameter of the particles is 10 μm. The treatment plant makes 2 MGD a day. You propose using a circular basin where water enters the center and exits at the edge. What diameter basin is required given a 3.5 meter basin depth and water temperature of 15 ˚C

Consider the removal of soil particles in a settling basin. The particles have a density of 1.3 g /cm3. The diameter of the particles is 10 μm. The treatment plant makes 2 MGD a day. You propose using a circular basin where water enters the center and exits at the edge. What diameter basin is required given a 3.5 meter basin depth and water temperature of 15 ˚C

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter6: Hydraulic Conductivity

Section: Chapter Questions

Problem 6.12P

See similar textbooks

Similar questions

Ex.6: Drilling mud with 16 ppg density. The volume percentage of solids in it is (32%). Calculate the percentage of each on in the mud.
In a permeability test with constant load in the laboratory, the following are given: L = 250 mm and H = 105 cm². If the value of k is 0.014 cm/s and a flow rate of 120 cm³/s must be maintained through the soil, what is the difference in charge, h, across the sample? determine also the percolation rate under the test conditions.
A sedimentation basin in a water treatment plant has a length = 50 m, width = 10 m, and depth = 4 m. Particle density = 1.1x10 kg/m'; water density = 10' kg/m2; and dynamic viscosity = 1.307x10-3 N.sec/m2. What is the flow rate, Q, that would remove 70% of particles with a diameter of 0.4 mm?
You are trying to remove 10.0 μm diameter particles in a water treatment plant, so you design a settling basin. The water is at 20 ̊C (giving a water density of 998.2 kg/m3, but really you can assume 1000 kg/m3 here), and the particle density is 1.2 g/mL. The plant treats 0.100 m3/s of water. It is proposed to use a 3.5 m deep, rectangular sedimentation tank with a length to width ration of 5:1. What is the minimum required width of the basin?
PLS SHOW YOUR COMPLETE SOLUTIONGiven the laboratory results of the Atterberg Limits Test in the following figure, plot the water content versus the number of blows. a. Determine the nearest value to the Liquid Limit of soil. Answer: 47.1%b. Determine the nearest value to the Plastic Limit of soil. Answer: 38.34%c. Determine the nearest value to the Liquidity Index of soil. Answer: 1.55
Which of the following is not a mode of field flow fractionation? a. Viscosity b. Sedimentation c. Flow d. Thermal
Q1-) A soil sample in plastic limit state weighs 2.535 N and becomes 1.980 N after oven drying. The plasticity index and the shrinkage limit of the soil are 11% and 15% respectively. Determine the quantity of water in liter to be added or taken out of the sample to change its state to: i- Solid state. ii- State at which the liquidity index equals to two.
The following results were obtained from a liquid limit test on a clay using the Casagrande cup device. The natural water content of this clay is 38% and the plastic limit is 21%. No. of blows 6 12 20 28 32 Water 52.5 47.1 42.3 38.6 37.5 content (%) What is the liquid limit of this clay? b. What is the plasticity index of this clay? What is the liquidity index of this clay?
Water is flowing through three soil layers as shown in Fig. Q2. The cross-section is a square with sides of 100 mm. The hydraulic conductivity (also known as coefficient of permeability) of each soil layer is given in Table Q2. a. What is the equivalent hydraulic conductivity of the three layers? b. Determine the flow rate exiting the system. c. Determine the elevation head diagram, the total head diagram, and the pressure head diagram from point A to point B. Ah = 30 cm h, = 50 cm h2 = 20 cm B D = 10 cm 3.33 cm 3.33 сm 3.33 cm O Datum 45 cm O Datum Fig. Q2: Three-layer permeameter
A constant-head permeability test is performed in a laboratory where the soil sample is 25 cm in length and 6 cm2 in cross-section. The height of the water is maintained at 2 ft at the inflow end and 6 in. at the outlet end. The quantity of water flowing through the sample is 200 ml in 2 minutes. (a) Make a sketch of the described conditions. (b) What is the coefficient of permeability? ***Please include all the units and conversions.
In a laboratory test of an aquifer material a fully saturated sample of volume 5 liters was taken and its initial weight of 105 N was recorded. When allowed to drain completely it recorded a weight of 97 N. The sample was then crushed dried and then weighed. A weight of 93 N was recorded at this stage. Calculate the specific yield and relative density of the solids. (Assume unit weight of water γγ=9.79 kN/m3) Answers: Specific yield= 16.34%; Relative density of solids = 2.517
2.28. A groundwater is being considered for use as a domestic supply. The water has a temperature 15°C and the following chemical analysis: CONSTITUENT Ca+2 Mg Nat Fe +2 Cd+ HCO3 SO4 CO3 NO3 CONCENTRATION. g/m³ 190 84 75 0.1 0.2 260 64 30 440 35 a. Use an anion-cation balance to determine if the sample analysis is reasonable. b. What is the hardness of the water? c. Determine the alkalinity of the water. d. Estimate the sample pH. e. Would the water be an acceptable domestic supply? Why or why not?