6. During a short interval the slotted guides are designed to move according to x = 16-12t + 4t² and y = 2 + 15t-3t², where x and y are in millimeters and t is in seconds.At the instant, 1 = 2 s, determine the radius of curvature p of the path of the constrainedpin P. (See Fig. 6 below)PFig. 6y

Given DataFind OutThe radius of curvature of the path of the constrained pin P

Answered: determine the radius of curvature p of…

Engineering

Mechanical Engineering

determine the radius of curvature p of the path of the constrained 1)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two radio transmitters positioned 400 mi apart along the shore send simultaneous signals to a ship that is 200 mi offshore and sailing parallel to the shoreline. The signal from transmitter S reaches the ship 200 microseconds later than the signal from transmitter T. The signals travel at a speed of 186,000 miles per second, or 0.186 mile per microsecond. Find the equation of the hyperbola with foci S and T on which the ship is located. (Hint: For any point on the hyperbola, the absolute value of the difference of its distances from the foci is 2a.) 200 mi Help me solve this C 400 mi Assume the origin is located at the midpoint of the foci. What is the equation of the hyperbola with foci S and I on which the ship is located? (Simplify your answer. Type your answer in standard form.) View an example Get more help. Ship Clear all Skill builder Check answer orre
4. 2) The hydraulic cylinder D extends, moves the rigid rod ABC, and causes the collar A to move with velocity and acceleration both to the left. If the dimensions 4 1.0 ft, and 2 = 1.7 ft, VA = 4.9 ft/s, aa = 2.6 ft/s2, and the angle 0 = 27°, determine the speed of point B. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. В 12 D a Your Answer: Answer units 1,
The r-y coordinate system is body fixed with respect to the bar. The angle 0 (in radians) is given as a function of time by 0 = 0.1+0.08t². The a coordinate of the sleeve A (in feet) is given as a function of time by x = 3+0.06t3. Determine the velocity of the sleeve at t = 4 s relative to a nonrotating reference frame with its origin at B. (Although you are determining the velocity of A relative to a nonrotating reference frame, your answer will be expressed in components in terms of the body-fixed reference frame.) (Figure 1) Enter the a and y components of the velocity separated by a comma. Πν ΑΣφ It vec ? VA 2, VA y = 2.88,4.92 ft/s Submit Previous Answers Request Answer X Incorrect; Try Again; 6 attempts remaining Figure < Return to Assignment Provide Feedback 1 of 1
Problem 1 A Mechanisms Enthusiast Club is using a rigid bar (length LAB = 18 in.) with wheels riding along horizontal and sloped (angle = 45°) surfaces to demonstrate rigid body acceleration. Point B is measured with video analysis software at the instant shown (ß = 30°) to be traveling at VB = 20 in/s to the right while slowing down at ag = 5 in/s². A Using vector math, determine the velocity and acceleration of point A. Ө B G LAB ав B VB
The piston of the hydraulic cylinder gives pin A a constant velocity v = 2.1 ft/sec in the direction shown for an interval of its motion. For where r = OA. the instant when = 54%, determine , r, 0, and 6.1" ✓ Answers: r = r = 0 = ÿ = i -1.6989 i 1.9645 i 2.425 10.623 ft/sec ft/sec² rad/sec rad/sec²
1. A motor winds the pulley at A with the kinematic quantities given. Find the acceleration of block E at this instant. (Figure difficult? The radius of the wheel B to the fixed rope is 50 mm, while the radius of the wheel attached to A is 125 mm.) I believe the difficulty to this problem, to the degree it is difficult, is in recognizing what you have and putting it into a familiar form. Feel free to contact me to discuss it. 50 mm A-40 rad/s 4-5 rad/² 50 mm B 125 mm
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity W and angular acceleration a (both counterclockwise). 2) if W = 4.2 rad/s and a = 8.0 rad/s2, what is the magnitude of the linear velocity of point A? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. 0.5 m A 0, a B Your Answer: Answer units
5. For the following pin-collected link assembly, link AO is pinned at point O, and moves with angular velocity and angular acceleration a (both counterclockwise). 2) if W = 3.7 rad/s and a = 7.6 rad/s², what is the magnitude of the linear velocity of point A? Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point, and proper unit. B Your Answer: 0 Answer A 0.5 m units ω, α
Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A plastic film moves over two drums. During a 5.25-s interval the speed of the tape is increased uniformly from vo= 2 ft/s to v1= 4 ft/s. The tape does not slip on the drums. Vo Vo 9 in. 15 in. Determine the angular acceleration of drum B. (You must provide an answer before moving to the next part.) The angular acceleration of drum Bis Trad/s2 O.
‚A Given: The arm of the robot is extending at a constant rate r = 1.5 m/s when r = 3 m, z = (4t2) m, and 0= (0.5 t) rad, where t is in seconds. Find: The velocity and acceleration of the grip A when t = 3 s. Plan: Use cylindrical coordinates.
The piston of the hydraulic cylinder gives pin A a constant velocity v = 2.4 ft/sec in the direction shown for an interval of its motion. For the instant when 0 = 59°, determine i, ř, 0, and Ö where r = OA. A. 5.3" Answers: ft/sec ft/sec? rad/sec = rad/sec2
For the mechanism below, at this instant, angle = 42°, rod BC has angular velocity W = 4.3 rad/s, and angular acceleration a = 3.0 rad/s². Link AC is pin-connected to collar C which slides freely on rod BC. Determine the magnitude of the angular velocity of link AC at this instant. Please pay attention: the numbers may change since they are randomized. Your answer must include 2 places after the decimal point and proper unit. A Lo 1 m Your Answer: Answer α (0) B units