Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = ___ (5 decimal places)

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = ___ (5 decimal places)

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter12: Composite Materials

Section: Chapter Questions

Problem 12.7P: Estimate the transverse tensile strength of the concrete in Problem 12.6.

See similar textbooks

Related questions

Q: Kim Jisoo discovered an element (1.43 kN/m3) that flows through a 100 mm (diameter) pipe at a mean…

A: Given data in question Unit weight Diameter Velocity To find out Mass flow rate

Q: solution use the slope deflection method 40 kN/m Ak 6 m 6 m 6 m

Q: What is the value of negative skin friction for a group of 4 piles of 25 cm diameter, 6 m long and…

A: Given data- 4 piles of 25 cm diameter6 m long and spaced at 80 cm c/cundrained shear strength=25…

Q: Problem 5. A small river is in flood stage and you need to estimate the flow rate through it. The…

A: Q= 1.49nAR23S12 A= 2000 sqft P= 620 ft R= 2000/620= 3.226 ft Assuming S= 0.001 By COX METHOD,…

Q: Use Moment Area Method to find the EIy value at the midspan

A: ∑MA=04000 + 2000×8 + 4000 - RC×16 = 0 RC=1500 lb ↑∑V=0RA+RC=2000RA+1500=2000RA=500 lb ↑Bending…

Q: The simply supported beam consists of a W460 x 82 structural steel wide-flange shape [E = 200 GPa;…

Q: Find the required slope of a rectangular open channel when the water flows at a rate of 20,000 L/s,…

A: Option (E) is most appropriate answer.

Q: A submarine is 109.36 yards. The shape of its hull is roughly cylindrical with a diameter of 15m.…

Q: 3 KNm 3m uの NUMBER 1 FIGURE 7 Im

Q: - FIND REACTIONS -DRAW SHEAR PIAGRAM - DRAW MOMENT PIAGRAM Wz= 0.5k 6' 121 V-o VMAX %3D Mmax = MMAX=…

Q: Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its viscosity is 1.15x10-7…

Q: 3) Concrete achieves its full strength after a day period? a) 45 b) 28 c) 7 d) 3 4) #8 Resteel has a…

A: ASKED: To complete the given statement using the given options. Given statement: Concrete…

Q: Given data : Force=0.5 N Displacemnt=1 m Determine work done

Q: A1 Present the shear force and bending moment diagrams of the following beams and frames (Figure…

Q: Design a beam of 5 m effective span, carrying a uniform load of 20 kN/m if the compression flange is…

Q: 4. A beam has a width of 300mm and effective depth of 540mm, d' 60mm. It is reinforced with 4-25mm…

A: A beam is defined as a horizontal structural element to resist vertical or laterally applied loads.…

Q: An aluminum pipe has a length of 59 m at a temperature of 11°C. An adjacent steel pipe at the same…

Q: Situation #1: Compute for the force on memhec EG and identify if it is in tension of compression. 13…

A: Compute for the force on member FG and identify if it is in tension or compression.

Q: a soil sample has a mass of 2290 g and a volume of 1.15x10 m After being completely dried in an oyen…

A: Given data : The value of specific gravity of soil solids GS=2.68 The value of volume of soil…

Q: 12 KN/m 10KN/m A 8 m 7 m

Q: The client has unexpectedly to extend the span of the beam by 1.0m. Discuss what are you required to…

A: Increase in Span of a beam increases the BM and SF of the beam and hence would require a larger…

Q: reinforced concrete slab is shown in Fig. Ex. 7.3(a). Design the beams (f, = 250 MPa) if the unit…

Q: Explain Fire Barriers and how they differ from Fire Partitions?

Q: For the beam below, determine the maximum negative shear at point D due to a concentrated live load…

A: Given data in question Span member length Dead and live load To find out Maximum negative shear…

Q: Situation 2 - For a constant laboratory permeability test on a fine sand, the following data are…

Q: What is the vertical reaction at A for the frame shown? 2 k/ft 100 k ft 15 ft El = constant E =…

Q: VE FOR THE SUPPORT REACTIONS AND DRAW THE SH GRAM OF THE FOLLOWING. NOT JUST WRITE THE MDM TABLE.…

Q: What is the fixed end moment FEMas for the beam with a settlement of 25 mm at support C? 20 kN/m 60…

A: Figure is as shown

Q: Calculate how long it will take for consolidation to be almost completed (reach ca. 95% of ultimate…

A: Data is as shown

Q: 21. You have a wellbore that is drilled to 3,298 feet measured depth. Inside it, the customer ran…

A: Option D-378.32

Q: NOTE: This is considered as a FRAME WITHOUT SIDESWAY Using the Moment Distribution Method (MDM) w…

A: MFDA = -17x6x3 =-306 kN-m

Q: A simply supported beam of span 29. 52 ft. carries two-point loads 210 KN and 125 KN at 6.56 ft. and…

Q: 6. Timber floor: The cross-section of the beam is 8x22cm (bxh), axial spacings 0,60 m. Timber class…

Q: 1. Strength of properly dried wood is significantly higher than that of green (freshly cut) wood. 1.…

Q: 4. If the open cylindrical container rotates at an angular velocity of 8 rad/s, determine the…

Q: The simply supported beam consists of a W460 × 82 structural steel wide-flange shape [E = 200 GPa; I…

Q: Situation 13 - The soil is acted upon by a uniformly distributed load AP = 60 kPa at the ground…

Q: Given the following Northing and Easting, use the COORDINATE METHOD to solve for the area of this…

Q: The steel column has an outer diameter of 4 in. and inner diameter of 3.5 in. is carrying a load P =…

A: ASKED- To determine: a. compressive stress in the column b. bearing stress of the concrete c.…

Q: 300 mm diameter pipe with a friction factor of 0.02 conducts fluid between two tanks at 3.04 m/s.…

Q: Steel joists are manufactured in different series to account for which of the following?…

A: Steel joists- Steel joists are an open web, lightweight metal trusses with matching hooks and a…

Q: PROBLEM 3 10KN/m 8 kN Determine the reactions at the supports A and C. The frame is pin connected at…

Q: which of the following statements is/are FALSE?

Q: For the dam cross-section shown below, determine the minimum value of b such that the resultant…

A: dam : A dam is a structure that is built across a stream or river. Water collects at the back of the…

Q: A retaining wall is to be constructed shown below. It has the following information: Soil Parameters…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: A sky lantern which a child tied to a piece of stone on the ground at the side of a tall multi-…

A: Given -

Q: An aluminum association standard l-beam 8x6.8181, uniformly distributed load of 1125lb/ft over a…

A: Figure is as shown

Q: or the frame below, if the axial force in column AE is 9.18 k, what is the approximate axial force…

Q: A cylindrical specimen of a cohesive soil of 10 cm diameter and 20 cm length was prepared by…

Q: A line was measured with a 50-m steel tape and its measured direction with the use of compass was S…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa.

if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = ___ (5 decimal places)

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. 16. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = [r] (5 decimal places)
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f'c = 21 MPa and steel yield strength fy = 420 MPa a.) if the tensile strain is es = fy/Es upon crushing of concrete at a strain of 0.003 b.) if the tensioe strain is set as 0.009 upon crushing of concrete at strain of 0.003 c.) minimum as required by NSCP 2015
SIT. B: Determine the tensile steel ratio of a given conditions if concrete strength f'. = 28 MPa and steel yield strength fy 4. if the tensile strain is Es = fy/Es upon crushing of concrete at a strain of 0.003. C. 0.02833 A. 0.01567 B. 0.02161 D. 0.02125 if the tensile strain is limited to 0.004 upon crushing of concrete at a strain of 0.003. A. 0.01567 B. 0.01548 5. 6. Minimum as required by NSCP 2015. C. 0.00313 D. 0.00405 A. 0.00333 B. 0.00276 = 420 MPa. C. 0.02778 D. 0.02064 uniformly
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 28 MPa and steel yield strength fy = 420 MPa. 1. if the tensile strain is εs = fy/Es upon crushing of concrete at a strain of 0.003. = (5 decimal places) 2. if the tensile strain is set as 0.010 upon crushing of concrete at a strain of 0.003. = (5 decimal places) 3. Minimum as required by NSCP 2015. = (5 decimal places)
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c=28MPa and steel yield strength fy=420MPa. If the tensile strain is set as 0.010 upon crushing of concrete at a strain of 0.003
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c=28MPa and steel yield strength fy=420MPa. If the tensile strain is upon crushing of concrete at a strain of 0.003
A singly reinforced rectangular section has a width of 250mm and an effective depth of 460mm. The concrete has a compressive strength of 21MPa. The steel has a yield strength of 275 MPa and E = 200,000 MPa. Calculate the ideal flexural strength for the following areas of steel: a. 2580 mm² b. 5160 mm² c. The value at balanced failure
3 Given a concrete beam (width b= 10 in., depth h = 25 in.) with flexural reinforcement at the bottom, the transformed moment of inertia is In=14,740 in“, and the location of the neutral axis from top of the beam is y = 13.2 in, assuming all material is elastic, calculate the maximum tensile stress of the concrete when a positive bending moment M= 40 kip-ft is applied to the beam. Is the section cracked under the given moment if concrete is normal weight and the compressive strength fe' is 3000 psi?
A pretensioned member with a dimension of 250mm x 360mm is subject to an eccentric tendon that is located 105mm from the soffit. Area of the prestressing steel to be 502 sq. mm and the modulus of elasticity is 200 GPa. The Modulus of elasticity of concrete is 36.8 GPa. Creep coefficient = 1.6 and the shrinkage strain = 3 x10^6. Assume a 5% steel relaxation. Find the total prestressed loss in percentage.
1. Shown is a composite plate joined together by rivets. The components consist of two tension bar plates that is % X 4 inch and riveted together by two splice plates which is 0.8 X 6 inch. Each rivet has a diameter of 25.4 mm. Considering that the allowable stress for the tension bar plates and splice plates is o=20.0 ksi, the allowable shear stress for the rivets is o=25.0 ksi and the allowable bearing stress on the rivets and splice plates is o=25.0 ksi. What will be the maximum permissible load P such that none of the allowable stresses will be exceeded? Splice Plates a-0.75 in Bar Lc =0.80 in. Bar P d = 1.0 in. b=4.0 in. Rivets 'e = 6.0 in.
A reinforced concrete beam has a width of 300 mm, an effective depth of 500 mm and is reinforced with a steel having an area of 1200 mm^2. The beam is subjected to a bending moment of 70 kN- m. If the modular ratio = 8, using WSD, Cracked Analysis. a) Determine the stress developed in the concrete. O 7.914 MPa 8.903 MPа 5.936 MPa 6.925 MPa None of the Choices 9.893 MPa