Answered: Determine the vertical shear stress…

Determine the vertical shear stress components at point q. Report your answer rounded to the nearest psi. 120 in 10 lbs/in 60 in 1500 lbs 60 in cross section: t = 0.75" Z 7=2.875" 6" 9 6.75 1.25"

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 4. A flat site is underlain by two layers over rock. The top layer is a CL with thickness = 3m,…

Q: The two beams are connected by an ideal pin at C. Draw the shear and moment diagrams for the…

A: Given:Required:Shear force and bending moment diagramMaximum magnitude of bending moment in each…

Q: 8-17. Remove the loads on the truss in Prob. 8-16 and determine the horizontal displacement of point…

A: A truss is hinged at A and E.The member AB and BC are subjected to temperature change by The…

Q: A trapezoidal channel is designed based on hydraulically efficient channel cross-section. The…

A: The trapezoidal section is hydraulically efficient.The slope of the section, S = 0.0035Manning's…

Q: One lane of a uniform section of highway has an optimum density of 70 vehicles per mile and an…

A: Optimum density=70 veh/mileOptimum speed= 35mile/hr

Q: Based on a Greenshields' model with a jam density of 120 vpmpl and a free flow speed of 60 mph,…

Q: An unconfined aquifer has a porosity of 0.45, and specific yield is 0.25. The dimension(s) of the…

A: The objective of the question is to estimate the volume of groundwater that can be withdrawn from an…

Q: Problem #4: An 18-in.-long steel rod is subjected to a tensile (a) The tensile stress (b) The strain…

Q: 1 A steel bar is 40 mm in diameter for a length of 100 mm, 30 mm in diameter for a length of 60 mm…

A: Reinforcing bars, or rebars, are a type of steel bar. It's a steel wire mesh that's used as a…

Q: A 20 m long concrete pile with a rectangular cross section of 460 mm x 460 mm fully embedded in sand…

Q: Q-B/Find the maximum value of) for the beam shown below, use f=35 MPa nd fy=400 MPa N10 kN/m…

Q: A standard triangular channel is lined with fresh concrete (n=0.013) and is designed based on the…

Q: Problem 1: A 6-m long cantilevered beam, 250 mm width x 600 mm deep, carries a uniformly distributed…

Q: ituation 4: Three layers of soil are shown with the corresponding values of coefficient of…

A: Q. 7 & 8 has some missing data or content. But Q. 9 & 10 can be answered from the given…

Q: Question 1: A wooden member with a compressive load of 100 kN is supported at the end shown.…

A: Question 1: A wooden member with a compressive load of 100 kN is supported at the end shown.…

Q: Determine the gage pressure at A in the given open-type manometer. Water 2 A 0.7 1.6 Hg

Q: If a dairy processing factory produces an average of 246 m³/d of wastewater with a BOD5 of 1400…

A: A dairy processing factory produces discharge Q= 246 m3/d of wastewaterper capita daily sewage flow…

Q: Consider the force F with a magnitude of 90.0 pounds acting at the point B in the positive z…

A: X= 4.70ftY=0.200ftZ=0.600ftF=90lb

Q: H.w:-prove that 01 σe = Ao A

A: Ture stress is the ratio of force applied to the area of cross section at the time of measurement of…

Q: Q4-An undisturbed sample of clayey soil is found to have a wet weight of 285 N, a dry weight of 250…

Q: The figure below shows a 20 m thick layer of normally consolidated clay (ϒt = 18.6 kN/m3) that is…

Q: A researcher was observing traffic along one lane of a rural highway. During a 1 minute time…

Q: A W12 x 79 of A572 Grade 60 steel is used as a compression member. It is 28 feet long, pinned at…

A: Properties of steel are taken from AISC table.

Q: Explain the following concept related to pile foundations and use figures for illustration. *…

Q: 200 KN F чт 1-Draw the Shear Force Diagram? 2-Draw the Bending Moment Diagram? B 150KN

A: The frame is shown in the above figure. We have to find out the followings: Shear force…

Q: The data in the table below is for a closed-polygon traverse. Balance the traverses by coordinates…

A: CourseLengthBearingAB403.73N 8o17'02"EBC622.63N 87o02'05"ECD653.16S14o47'06"WDA550.84N 68o43'20"W

Q: Q. 4 Determine all reactions and draw the shear and moment diagrams for the beam shown below. El is…

A: EI = ConstantDetermine the support reaction and draw the shear force and bending moment diagram of…

Q: Determine the internal normal force, shear force, and moment at point C of the beam.

Q: Assuming suitable design criteria, design a primary settling tank to treat 10000 m³/d average…

Q: P9.5 A cantilever wooden beam (Figure P9.5a) consists of eight 2 in. thick planks glued together to…

A: Determinea. Horizontal shear stress at points A, B, C and D. b. Plot the shear stress distribution…

Q: Referring to Figure below. it shows the section of a Barrage. The various dimensions and levels are…

Q: Problem 2: Boundary Layers State an example where engineers deliberately modify a surface to create…

A: There are many instances where engineers deliberately modify a surface to create a turbulent…

Q: (ii) Explain why it is generally necessary to assess the feasibility of a draft design…

A: The objective of the first part of the question is to understand the importance of assessing the…

Q: knThe Fh is correct 397.305 The Fv is incorrect i am getting 356.887 Kn the area is the area of…

A: Fx = 397.305 kN We need to calculate correct value of vertical hydrostatic force Fv

Q: A researcher was observing traffic along one lane of a rural highway. During a 1 minute time…

A: Give data:-The given time interval is, 1 minutewe observed the number of vehicles, 10 vehicles

Q: An open cylindrical vessel 1.2m in diameter and 2.1m high is 2/3 full of water. Compute the amount…

Q: Select the lightest W-section for the simply-supported beam shown. The beam is subjected to a…

Q: = Phase Number Protected Movement Permitted Movement > Pedestrian Movement In this ring and barrier…

A: Split phasing is considered when there is a need for a left turn lane, but no spacing width is…

Q: 1500N/m Calculate the magnitudes of the reactions at A, B, and C for the frame shown. Neglect the…

Q: A truss has geometry and loads as shown in the figure and parameter table. Use method of sections to…

Q: Determine the reactions for the beam in the given figure. When & uniform load is applied, the fixed…

A: E = 30000 Kips/in.2I = 240 in.4Support B settle (∆) = X = 0.2 in. Determine the support reaction of…

Q: For the slab shown in the figure, Fy= 420 Mpa, Col. Dimensions = 400 x 400 mm, check slab thickness…

A: Yielding stress of steel= fy = 420 MPaColumn dimension= 400 x 400 mm We have to check the slab…

Q: 1. For P = 1200N, what are forces in members AB, AC and BC? Draw FBD of entire structure - removing…

Q: Determine the magnitude and direction of the resultant force for the following forces acting on a…

A: Given Data,To find the resultant force for the given force system,At 60°, a 30 N force acts in the…

Q: determine the Concrete Shear Force and Critical Spacing of Stirrups to be adopted by the entire grid…

Q: Required information Consider the beam given in the figure. Given: X = 0.4 in, E = 30,000 kips/in²,…

A: E = 30,000 kip/in.2I = 240 in.4Determine the support reaction and draw the shear force and bending…

Q: An old 6-lane (3 lanes each direction) rural freeway segment has 11 ft lanes and frequent roadside…

A: A 6-lane road with 3 lanes in each direction. Width of lanes = 11 ftLocation of frequent road…

Q: 6 kip.ft nax max A = kips C kip-ft 6 ft P 3 kips 4 kips. D ermine the maximum absolute values of the…

A: P= 5.5 kipsto determine the maximum absolute values of shear and bending moment-

Q: An open cylindrical tank 1.6m in diameter and 2 m high is full of water. When rotated about its…

A: Diameter of the tank =1.6 mRadius of the tank = 0.8 mHeight of the tank= 2 mAngular velocity =…

Q: 9-10 The beam shown in Fig. P9-10 is made of 4000-psi concrete and supports dead and live loads of 1…

Concept explainers

Methods to Determine Vertical Stress

The load applied to the soil is transferred to the underground. The presence of water at soil pores and solid grains above the soil are the primary components that are responsible for the effective load transfer. Due to the load acting, the internal component of the soil or the underground formations undergoes deformations or a tectonic shift. The amount of deformation depends upon the amount of load acting on the soil surface, which indeed, depends on the weight of everything present above the soil. Due to this, the underground soil element develops internal stresses which try to resist the tectonic changes.

Question

Name:
Determine the vertical shear stress components at point q.
Report your answer rounded to the nearest psi.
120 in
10 lbs/in
60 in
1500 lbs
60 in
I
cross
section:
t = 0.75"
z
7=2.875"
6"
9
6.75"
1.25"

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introducing given data

VIEW

Step 2: Calculate shear force at point q

VIEW

Step 3: Calculate moment of inertia

VIEW

Step 4: Calculate vertical shear stress

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

30. 15 15 30 20 Ratio of major principal stress to minor principal stress up to two decimal places only
An 8 m simple beam is loaded with a 228 kN point load at the first third of its length. The cross section of the beam is shown below. If the allowable stress is 200 MPa the thickness of the cross section is constantly t - 18 mm C t Y ▼ 2 Find the dimension c of the cross section such that it will satisfy the allowable stress. Select the correct response: 318.329 mm 290.593 mm 355.903 mm 263.312 mm
Angle 1 Tyx Txy x-direction stress 60OMPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: Using a Mohr circle determine the stresses on the plane of the indicated angle 1. (50°). Show al calculations. Draw the orientation of the stress block for this scenario.
Estimate the shear strain yxy at point D with respect to the xx and yy directions. A rectangle ABCD has width 400 mm (in the x-direction) and height 300 mm (in the y-direction). It deforms into the shape in the dashed lines. Point A (lowe right corner) moves to the right by 3 mm and upward by 2 mm, point B (upper right corner) moves to the right by 5 mm and upward by 4 mm, point C (upper left corner) moves to the right by 2 mm and upward by 2 mm.
Q.3) The original and deformed geometries of a Plastic block subjected to axial and shear stresses is shown below. Determine the average normal strains along diagonals AB and CD. Also find shear strain Yxy at each of its corners A, B, C and D. y D' 107 mm A D 91.5° 100 mm 5 mm B' B 100 mm C' 12 mm
Problem 7: The rectangular plate is deformed into the shape shown by the dashed lines. Determine the average normal strain along diagonal AC, and the average shear strain at corner A relative to the x, y axes. (8 pts) 6 mm -400 mm 2 mm mm fom 300 mm 2 mm A B 400 mm -3 mm
4.15 The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. La 15 mm 40 mm 20 mm 粗眼 d = 30 mm M R Fi
axial load= 119x10^3 kips.find compressive stress,the location of the resultant of the load.
(a) Determine the magnitudes of the stresses (report positive numbers here) at H caused by the forces and moments of Parts 1 and 2. Answers: OHaxial i ! МРа, OHbend = 123.615 MPa, THshear MPа, THtorque MPa. 50.499
The cross section of the CD part of the crane boom in the picture is a standard 50x150mm2. Determine the normal stress at the center of the part. Use exact values in the calculation, just round the answers!
0.200 mm S R 250 mm 0.380 mm P 500 mm A thin rectangular plate is uniformly deformed as shown. Determine the in-plane shearing strain at point P rad 0.00156 rad 0.00076 rad 0.00080 rad 0.00257 rad 0.00128
PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 5Ở KN are applied at both plates in opposite directions as shown in Figure 3. Compute the following: A. Axial stress of each plate. B. Shear stress of each bolt. Assume that each bolt resists the applied force equally. %3D +F 150 mm 中 F 50 mm 340 mm Figure 3: Bolted Plates