Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when = 35° and P = 196 N. Given: μs = 0.20 and μk = 0.15. 800 N 25° The block is not in equilibrium. True The magnitude and direction of the friction force is N (K

Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when = 35° and P = 196 N. Given: μs = 0.20 and μk = 0.15. 800 N 25° The block is not in equilibrium. True The magnitude and direction of the friction force is N (K

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Determine whether the block shown is in equilibrium and find the magnitude and direction of the friction force when P = 100lb. 50 lb H, = 0.40 Hi = 0.30 40° 30° O Block is in Equilibrium, F-43.032 Ib, 30 deg. with the Harizantal Axis O Block is in Equilibrium, F-32.274 b, 40 deg. with the Harizontal Axis O Block is not in Equilibrium, F-32.274 lb, 30 deg. with the Horizontal Axis O Block is in Equilibrium, F-32.274 b, 30 deg. with the Horizontal Avis O Block is not in Equilibrium, F-43.032 lb, 30 deg, with the Horizontal Axis
6. Determine whether the block shown is in eguilibrium and find the magnitude and direction of the friction force when P = 150 N. 500 N µ, = 0.30 Hk = 0.25 20°{
PROBLEM 2.78 A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid supports as shown. For the type and grade of rubber used r =1.54 MPa and G=12.6 MPa. Knowing that a centric vertical force of magnitude P=13 kN must cause a 2.5-mm vertical deflection of the plate AB, determine the smallest allowable dimensions a and b of the block. 75 mm bnin = 56.3 mm = 20.5 mm a min
A 40m steel tape is suspended in the air between a theodolite and vertical rod, which is placed exactly at the 40m mark, under a pull of 12.5kg. The slope of the measured line is 2-degree 40minutes. The tape weighs 1kg, standard pull of 8.5kg, cross-sectional area of 0.039cm^2 and E= 2x106 kg/cm^2. Determine the correction for sag of the tape in meter. Determine the horizontal distance between the theodolite and rod in meters. (Apply 5-decimal places - for letter B only) What additional pull must be applied to eliminate the effect of sag?
Line AB was determined to be 2395.25m when measured with a 30m-steel tape supported throughout its length under a pull of 4kg and at a mean temperature of 35°C. The cross- sectional area of the tape is 0.03 cm^2, coefficient of thermal expansion is 0.0000116/°C and modulus of elasticity of steel is 2.0x10^6 kg/cm^2. Determine а. Correction for the measured length due to temperature if the tape used is of standard length at a temperature of 20°C. Is the tape too long or too short? b. Correction for the measured length due to tension if the tape used is of standard length at a pull of 5 kg. Is the tape too long or too short? C. Correction for the measured length due to sag if it weighs 0.04kg/m d. the corrected length of line AB considering corrections from (a), (b) and (c)
2. The velocity distribution of a viscous liquid flowing over a fixed plate is given as V= 0.68 y - y? for 0sy<0.34 m. "y" is the distance from the plate in meters and the unit of the velocity is m/s. Calculate the shear stress at the plate surface (y=0) and 0.34 m away from the plate (0.9 Ns/m2). Draw the velocity and shear stress profiles. Fixed plate flow
Take o, = 580 kPa (Figure 1) Express your answer to three significant figures and include the appropriate units. HÀ ? o, = Value Units Submit Request Answer Figure Part B Determine the shear stress acting on the inclined plane AB. Express your answer to three significant figures and include the appropriate units. В HA ? 30° Value Units A
A line is recorded as 472.90 m long. It is measured with a 0.65 kg tape which is 30.005 m long at 20 °C under a 50 N pull supported at both ends. During measurement, the temperature is 5 °C and the tape is suspended under a 75 N pull. The line is measured on 3% grade. E = 200 GPa, cross-sectional area of the tape is 3 mm2 and the coefficient of linear expansion is 0.0000116 m/°C. a. Compute the actual length of tape during measurement. b. Compute the total error to be corrected for the inclined distance. c. What is the true horizontal distance?
A circular Beam with roller joint R L y y oo = 298.6055 Pa Ro = 2.0649 m L = 61 m Material Data E[ GPA] Oyp [MPa] p [kg/m^3 V 200 0.3 700 7800 Find: Displacement in X, Y, Z direction, von misses stress, tresca stress, and triaxial stress at x = L, at x = L/2 and x = 0. Please show all work
What does the M=10 Kn.m represents? how do you call it? why on the Ma - 10 - (6.... why it is not Ma + 10. Please be specific I have doubts on this last steps of solution.
A hollow circular tube is subjected to a tension force of 30 KN, a tensile stress of 20 MPa was recorded.lf the outer diameter of the tube is 100 mm, the inner diameter will be eqaual to. a. 93.95 mm O b. 89.95 mm C. 85.95 mm o d. 91.95 mm
A 40m steel tape is suspended in the air between a theodolite and vertical rod, which is placed exactly at the 40m mark, under a pull of 12.5kg. The slope of the measured line is 2-degree 40minutes. The tape weighs 1kg, standard pull of 8.5kg, cross-sectional area of 0.039cm^2 and E= 2x10^6 kg/cm^2. a. Determine the correction for sag of the tape in meter.b. Determine the horizontal distance between the theodolite and rod in meters. (Apply 5-decimal places - for letter B only)c. What additional pull must be applied to eliminate the effect of sag?