Droblem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with diameter d=10 mm. Determine the axial stress o in the truss member (1) and the axial stress o6 in the truss member (6). 2 kN 3 kN 2 m 2 m (1) (3) (6) (4) 1.5 m D 1.5 m (5) B.

Droblem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with diameter d=10 mm. Determine the axial stress o in the truss member (1) and the axial stress o6 in the truss member (6). 2 kN 3 kN 2 m 2 m (1) (3) (6) (4) 1.5 m D 1.5 m (5) B.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter7: Analysis Of Stress And Strain

Section: Chapter Questions

Problem 7.4.21P: -18 through 7.4-25 An clement in plane stress is subjected to stresses a,, ay., and axy. (see...

See similar textbooks

Related questions

Q: -2 Andrei is flying an SR-71 horizontally at 1,000m/s at an altitude of 20,000m where the speed of s...

Q: A pipe carrying steam at 3.0 MPa has an outside diameter of 450 mm and a wall thickness of 10 mm. A ...

Q: 3- A particle of mass m moves along a frictionless, horizontal plane with speed given by v(x)=k/x, w...

A: Given Data

Q: The shaft of a 7 HP lawnmower is 25mm in diameter and rotates at 1200 rpm. Calculate the shear stres...

Q: A particle at t=0 has the positive xo, the velocity v. is being acted on it by sinusoidal force F=Fo...

Q: A particular gyroscope is made by taking two long, skinny, solid cylinders affixed along their long ...

A: Solution: Given Data: m1=5 g=0.005 kgm2=350 g = 0.35 kgr2=5 cm=0.05 mr1=3 mm=0.003 m

Q: (a) (b) (2) (8) (3) (15) k(4,6) ji(4,6) k(-1,3)- j(8,2) i(6,2) i(1,1 (c) (d)

A: (a) here ,N1=L-XL =6-X6 ⇒N2=XL =X6

Q: and bottom flanges and is fastened by two rows of 20 mm rivets span of 6m and carries a uniformly di...

Q: In a nozzle, steam enters at T = 673.15 K and P = 800,000 Pa while u = 10 m/s. It exits at T = 400,0...

A: What is the ratio of the inlet and outlet diameters (D1/D2)?

Q: Construct the shear force and bending moment diagrams for the beam shown by the area method. Neglect...

A: Given Beam on load To find Shear force and bending moment

Q: F13-4. The 2-Mg car is being towed by a winch. If the winch exerts a force of T = (100s) N on the ca...

A: Given Data m=2 Mg T=(100s) N

Q: 1) The throttle-control sector pivots freely at O. If an internal torsional spring exerts a return m...

Q: A 3.5-hp pump delivers 1140 lbf of ethylene glycol at 20°C in 12 seconds, against a head of 17 ft. C...

A: Calculate the efficiency of the pump in %.

Q: (a) Calculate the tangential and longitudinal stresses in the steel. (b) To what value may the inter...

Q: A dam is proposed on a remote stream that measures approximately 25-cm deep by 350-cm wide with an a...

A: Handwriting.jpg

Q: Problem 2. For the mechanism in the configuration shown in the Figure, ro28 = 4.0 cm, rDB = 10.0 cm,...

Q: A container having pressurized gas in its upper part and water in its lower part. Pressure of the ga...

A: GivenP1=4MPam=1kgm=1kgV2=n×103Pa=1MPag=10

Q: For the beam and loading shown. a. Determine the distance x for which the maximum absolute value of ...

Q: Economics in power transmission system means ,is how we can select the power transmission system. Gi...

Q: From the codes below, how many seconds does the tool dwell at the bottom of the operation? (Two deci...

A: For the given drilling cycle G82= drilling cycle X,Y= hole position Z= depth R= Retract position in ...

Q: In the truss shown, find the value of 21 in degrees.

Q: Determine the crosssectional areas of members AG, BC, and CE fo

A: GIven: TO determine: Area of the member AG, BC, CE

Q: A golf ball is launched with the initial conditions shown in the figure. Determine the radius of cur...

Q: 22. True or False? With 3 + 1 milling, the additional axis is commonly referred to as the C axis. 23...

A: Milling Machine which different axes

Q: From the following Ni-Cu alloy phase dagram, predict phases present, phase composition, and phase am...

A: Solution: Given Data: CL=32%Co=34%Cα=43%

Q: A cylindrical sample of a biological product (10. mm in diameter and 18 mm in height) was exposed to...

A: Calculate the change in force in the time when it decreases to 36% of the initial value. Ft=F0-36100...

Q: duty of the heater in kW?

A: To find Duty of heater

Q: Q1/. A fan draws in air freely and discharges through a test duct of cross - section 0.07 m? in whic...

A: Write the formula for the efficiency of the fan. η=PoutPin Here, Pin is the input power, Pout is the...

Q: forecast sales for feburary 2022

A: Given; Exponential smoothing constant for a product is; α=0.2Actual sales for january 2021 is; Xs...

Q: 2. The A water tube boiler operates at 1800 psia has the following characteristic No. of riser 110 R...

A: Given DataP=1800psiaL=110ftd=6ft {tower diameter taken}Lc=90ft

Q: 1) if its angular velocity w as a function of angular position 0 is w=0.2-0², where O is in radian, ...

Q: required punch diameter ?

A: Given; A metal disc of,Diameter,d=40 mmIt is to be punched from a sheet of; Thickness,t= 4 mmThe pu...

Q: 6/9 A uniform slender rod rests on a car seat as shown. Determine the deceleration a for which the r...

Q: A reversible heat engine absorbs 3000 kJ from a reservoir at 1000 K and rejects 2500 kJ at 500 K. Fi...

Q: A fan is to be selected to cool a computer case whose d see the figure). Half of the volume in the c...

A: To given that,A fan is to be selected to cool a computer case whose dimension =12cm×40cm×40cmnow, ca...

Q: B 30° 3 m 2 m - 10 m

Q: The gearing arrangement suitable for this application is?

A: Given; A motor is connected to a stirrer and is running at; Nstirrer=36 rev/minPower of motor is=1...

Q: flat plate 30 cm by 50 cm slides on oil (μ = 0.8 N⋅s/m2) over a large plane surface. What force is r...

Q: Steam at a temperature of 250°C has a specific volume of 0.15436 m3/kg. What are the pressure, speci...

Q: What is the temperature of wet steam with 90% quality at 22 kPa?

Q: Q5. Choose the correct answer for each of the following: 1- Which of the following is not an interna...

A: This question is based on the concept of combustion engine.

Q: Mechanical System Design Home Work 2 PISTON DESIGN Q2: Design a cast iron trunk type piston for a si...

Q: Clearance volume of a reciprocating compressor is 300ml, and the volume of the cylinder at bottom de...

A: The clearance ratio of the compressor is 3/17.

Q: Еxample 2 During a high Reynolds number experiment, the total drag force acting on a spherical body ...

A: The friction drag coefficient of the sphere is CD,friction = 0.0115.

Q: Three linear elastic springs with constants kA, kB, and kC are connected to a rigid bar of length 2a...

Q: circular pitch and diametral pitch

A: Given; In spur gear having involute teeth,The product of circular pitch and diametrical pitch is ?

Q: Suppose that F1 = 19 kN. a) Determine the x and y components of reaction at pin A using scalar nota...

Q: clearance ratio of the compressor.

A: Given; Volume of the cylinder at bottom dead centre is; Vs=2 ltrClearance volume of a reciprocatin...

Q: A condenser takes in steam with enthalpy of 2450 kJ/kg and mass flowrate of 2 kg/s. It also discharg...

A: in condenser process is constant pressure.

Q: IDENTIFY THE NUMBER OF ATOMS (CL, C, H, and F) in the Refrigerant R40

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

Problem 6.4: Each member of the truss in Figure (6.21) is a solid circular rod with
fameter d=10 mm. Determine the axial stress o, in the truss member (1) and the axial
06
in the truss member (6).
stress
2 kN
3 kN
2 m
2 m
(1)
(3)
A
(6)
(4)
1.5 m
1.5 m
(5)
E.
B.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
A simply supported beam is subjected to point load P at mid-span. The normal stress on an element at mid-span is known to be ??x= 1.5 ksi. Determine the element stresses lilt is rotated through angle ? = 450• Show these stresses on a sketch of an element oriented at that angle.
, An arm A BC lying in a horizontal plane and supported at A (see figure) is made of two identical solid steel bars AB and BC welded together at a right angle. Each bar is 22 in. long. (a) Knowing that the maximum tensile stress (principal stress) at the top of the bar at support A due solely to the weights of the bars is 1025 psi, determine the diameter d of the bars. (b) If the allowable tensile stress is 1475 psi and each bar has a diameter d = 2.0 in,, what is the maximum downward load P that can be applied at C(in addition to self-weight
Solve the preceding problem if F =90 mm, F = 42 kN, and t = 40°MPa
-18 through 7.4-25 An clement in plane stress is subjected to stresses ax,ay., and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-18 sx= 2900 kPa, sy= 9100 kPar,txy=-3750kPa
-18 through 7.4-25 An clement in plane stress is subjected to stresses sx,??y, and r. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements. 7.4-23 ??x= 2050 psi, sy= 6100 psi, txy= 2750 psi
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
-26 A rectangular plate of dimensions 125 mm × 75 mm is subjected to tensile stress sy= 67 kPa and compressive stress a. If it is known that the normal stress along the diagonal t—t is ??t= -6.57 kPa, find stress ??y on element A. a
A sign is supported by a pipe (see figure) having an outer diameter 110 mm and inner diameter 90 mm. The dimensions of the sign are 2.0 m X 1.0 m, and its lower edge is 3.0 m above the base. Note that the center of gravity of the sign is 1.05 m from the axis of the pipe. The wind pressure against the sign is 1.5 kPa. Determine the maximum in-plane shear stresses due to the wind pressure on the sign at points /I, B, and C, located on the outer surface at the base of the pipe.
A cube of cast iron with sides of length a = 4.0 in. (see figure) is tested in a laboratory under triaxialsire.ss. Gages mounted on the testing machine show that the compressive strains in the material arc a = -225 X l06and,ay = 37.5 X l0_. Determine the following quantities: (a) the norm al stresses i. r,.. and acting on the x, y, and z faces of the cube; (b) the maximum shear stress r in the material; (C) the change ..W in the volume of the cube: (d) the strain energy U stored in the cube; (e) the maximum value of s when the change in volume must be limited to O.O28%; and (f) the required value of when the strain energy must be 38 in.-lb. (Assume £ = 14,000 ksi and v = 0.25.)
A fire extinguisher tank is designed for an internal pressure of 825 psi. The tank has an outer diameter of 4.5 in. and thickness of O.OS in. Calculate the longitudinal stress, the circumferential stress, and the maximum shear stresses (out-of-plane and in-plane) at the outer surface of the tank.
through 7.4-25 An clement in plane stress is subjected to stresses sx,??y,and txy. (see figure). Using Mohr’s circle, determine (a) the principal stresses and (b) the maximum shear stresses and associated normal stresses. Show all results on sketches of properly oriented elements.