Example :- Calculate the power in W/m required for mixing an oil of relative density 0.93 and viscosity 18 N.s/m² in a tank of 15 Cm diameter and 20 Cm height filled to three-fourths of its volume with oil, if the speed of the agitator is 500 rpm. Calculate the speed of agitator if the same mixing is carried out at the same Reynolds number in a doubled volume tank.

Example :- Calculate the power in W/m required for mixing an oil of relative density 0.93 and viscosity 18 N.s/m² in a tank of 15 Cm diameter and 20 Cm height filled to three-fourths of its volume with oil, if the speed of the agitator is 500 rpm. Calculate the speed of agitator if the same mixing is carried out at the same Reynolds number in a doubled volume tank.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

In a given setup, distilled water flows towards the inside and goes outside of the vessel as shown in the figure. What is the rate of change of the water's mass (dm/dt) in the vessel? 3 in. Q = 0.3 ft3/sec V = 30 ft/sec Device m = 0.3 slug/sec %3D
A 10 cm diameter solid cylinder of height 10 cm weighing 0.40 kg is immersed in a liquid (800 kg/cm^3) contained in a tall metal cylinder having a diameter of 13 cm. Before immersion, the liquid was 8 cm deep. At what level from the bottom will the solid cylinder float? W. = 0.40kg %3D 10cmo tank New L.S. Original L.S. F.
Crude oil (with specific weight γoil = 55 lb/ft3 ) is pumped at a rate of 400 gallons per minute from a test separator at A to the stock tank shown using a pipe that has a diameter of 4 inches. The pressure at A (to the left of the pump or prior to the pump) is 4 psi and the stock tank is open to the atmosphere. The friction head loss along the entire length of the pipe from A to B is 45 inches. Note that 1ft3 = 7.48 gallons. (a) Determine the velocity in the pipe. (b) Determine the head gain, ℎ??, delivered by the pump to the flow. (c) Determine the power required to run the pump if it is 90% efficient.
Several liquids are layered inside a tank with pressur- ized air at the top. If the air pressure is 3.2 kPa, calcu- late the pressure at the bottom of the tank if the lay- ers include 20 cm of SAE 10 oil, 10 cm of water, 15 cm of glycerin, and 18 cm of carbon tetrachloride.
Problem 7 - 69 Gasoline at 20°C (sp. gr. 0.719, u = 0.000292 Pa-s) flows at the rate of 2 L/s through a pipe having an inside diameter of 60 mm Determine the Reynolds number Ans: 104.400
As shown in the accompanying Carbon Tetra Chloride (Sp. Gr. 1.594) figure, pipe M contains carbon tetrachloride of specific gravity 1.594 under a pressure of 1.05 kg(f)/cm² and pipe N contains oil of specific gravity 0.8. If the pressure in the pipe Nis 1.75 kg(f)/cm? and the manometric fluid is mercury, Oil 2.5 m (Sp. Ģr. 0.8) N find the difference x between the levels of mercury. 1.5 m Mercury
A centrifuge bowl with internal diameter of 150mm is turning at 8000r/min is used to separate chlorobenzene, with a density of 1109 kgm3, from an aqueous wash liquid having a density of 1020 kgm3. The free liquid surface inside the bowl is 40mm from the axis of rotation. If the centrifugal bowl is to contain equal volumes of the two liquids, what should be the radial distance from the rotational axis to the top of the overflow dam for heavy liquid
Given the following pump data: 10 ft-positive suction head, 198 ft - discharge head, 16 ft- friction loss, 421 gpm - flow, Motor eff. Is 80% and Pump eff. Is 90%. What is the bhp? O23.10 bhp O 25.47 bhp O 26.53 bhp O24.16 bhp
An oil pump operating at steady state delivers oil at a rate of 10 lb/s through a 1-in.-diameter exit pipe. The oil, which can be modeled as incompressible, has a density of 70 lb/ft3 and experiences a pressure rise from inlet to exit of 40 lb/in². There is no significant elevation difference between inlet and exit, and the inlet kinetic energy is negligible. Heat transfer between the pump and its surroundings is negligible, and there is no significant change in temperature as the oil passes through the pump. Determine the velocity of the oil at the exit of the pump, in ft/s, and the power required for the pump, in hp.
When the accumulated liquid along the bottom of the pipe or in a well reaches a certain level and "plugs" the pipe, the higher velocity gas gets blocked. Select one: O True O False
A flocculator tank has a volume of 2800 m³. The temperature of water in the tank is 15°C, and the average velocity gradient maintained in the tank is 100/s. The temperature of water is reduced to 5°C, but all other operating conditions including the power input are maintained as the same. The decrease in the average velocity gradient (in %) due to the reduction in water temperature is (round off to nearest integer). [Consider dynamic viscosity of water at 15°C and 5°C as 1.139 × 10-³ N-s/m² and 1.518 x10-3 N-s/m², respectively]
Problem 13.84 The converging nozzle has an exit diameter of 0.25 m. The fuel-oxidizer mixture within the large tank has an absolute pressure of 4 MPa and temperature of 2100 K. The mixture has k = 1.38 and R = 296 J/[kg-K]. (Figure 1) Figure 0.25 m 1 of 1 Part A Determine the mass flow from the nozzle when the backpressure is a vacuum. Express your answer using three significant figures. IVE ΑΣΦ m = Submit Provide Feedback Request Answer vec ? kg/s