fe Water at 40°F (p = 62.42 lbm/ft³ and μ = 3.74 lbm/ft. h) is flowing through a 0.12-in (= 0.01 ft) diameter 30-ft long horizontal pipe steadily at an average velocity of 3 ft/s (Fig. 14-18). Determine (a) the head loss, (b) pressure drop, and (c) the pumping power requirement to overcome this pressure drop. -3 ft/s 0.12 in -30 ft-

fe Water at 40°F (p = 62.42 lbm/ft³ and μ = 3.74 lbm/ft. h) is flowing through a 0.12-in (= 0.01 ft) diameter 30-ft long horizontal pipe steadily at an average velocity of 3 ft/s (Fig. 14-18). Determine (a) the head loss, (b) pressure drop, and (c) the pumping power requirement to overcome this pressure drop. -3 ft/s 0.12 in -30 ft-

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Determine (a) the head loss, (b) the pressure drop, and (c) the pumping power for water flowing steadily at 40°F (ρ=62.42 lbm/ft3 and μ=1.038x10-3 lbm/ft-s) through a 0.15-in diameter, 45-ft-long horizontal pipe at an average velocity of 2.5 ft/s. Round off your answers to three (3) decimal places.
QUESTION 1 Water at 15°C (p = 999.1 kg/m³ and μ = 1.138 × 10-³ kg/m-s) is flowing steadily in a 30 m long and 6 cm diameter horizontal pipe made of stainless steel at a rate of 10 L/s. Determine: 1.1 the pressure drop, 1.2 the head loss, and 1.3 the pumping power requirement to overcome this pressure drop. דרס 30 m Figure 1 a 6 cm
Flow in Pipes and Frictional Losses Water at 158°C (r = 999.1 kg/m3 and u = 1.138 x 10-3 kg/ms) is flowing steadily in a 30-m-long and 5-cm-diameter horizontal pipe made of stainless steel at a rate of 9 L/s. Determine (a) the pressure drop, (b) the head loss, and (c) the pumping power requirement to overcome this pressure drop. 9 L/s - 30 m 5 cm
Example 2 Water at 10 °C (p = 999.7 kg/m³ and µu = 1.307 x 10-3 kg/m.s) is flowing steadily in a 0.2 cm diameter, 15 m long pipe at an average velocity of 1.2 m/s. Determine (a)The pressure drop (b)The head loss (c)The pumping power requirement to overcome this pressure drop
In a water Transfer installation, from the storage tank to the consumption tank, a pump is to be installed to circulate a flow rate of 60 lt/s. The 380 meter long Pipe is Made of cast iron of 150 mm diameter and consist of a check valve, a gate valve and 3 commercial elbows of medium Radius.The consumir tank is pressurized to 3.5 Kgf/cm2 gauge pressure.Determine the driving power of the KW pump if it's efficiency is 73%. Additional data, head loss factors: - check valve 1,7 - Open gate valve Kv= 0,19 -commercial elbow of average Radius Kc= 0,75, per elbow. - storage pond outlet sharp angles Ks = 0,5 - inlet to consumption pond Le = 1 - Pipe friction factor f = 0,029
Water at 15°C (p = 999.1 kg/m³ and u kg/m · s) is flowing steadily in a 30-m-long and 4-cm-diameter horizontal pipe made of stainless steel at a rate of 8 L/s. Deter- mine (a) the pressure drop, (b) the head loss, and (c) the pump- ing power requirement to overcome this pressure drop. 1.138 × 10–3 8 L/s 4 cm 30 m O
The valve in a piping system causes a 3.1 m head loss. If the velocity of the flow is 4 m/s, the loss coefficient of this valve is (a) 1.7 (b) 2.2 (c) 2.9 (d) 3.3 (e) 3.8
Water flows in a 15-cm-diameter pipe at a velocity of 1.8 m/s. If the head loss along the pipe is estimated to be 16 m, the required pumping power to overcome this head loss is (a) 3.22 kW (b) 3.77 kW (c) 4.45 kW (d) 4.99 kW (e) 5.54 kW
Water at 20°C is to be pumped from one tank (ZA=5 m) to another tank at a higher elevation (ZB=13 m) through two 36 m long pipes connected in parallel, as shown in the figure. . The pipes are made of commercial steel, and the diameters of the two pipes are 4 and 8 cm. Water will be pumped via a 70 percent efficient motor-pump coupling that extracts 8 kW of electrical power during operation. Minor losses and head loss in the pipes connecting the pipe joints parallel to the two tanks are considered negligible. Determine the total flow rate between the reservoirs and the flow rate through each of the parallel pipes. Hypothesis: 1.The flow is stationary and incompressible. 2. The input elects are negligible and therefore the flow is fully developed. 3. The elevation of deposits remains constant. 4. Minor losses and head loss in pipes other than parallel pipes are said to be negligible. 5. The flows through both pipes are turbulent (to be verified).
Water at 10°C (ρ = 999.7 kg/m3 and μ = 1.307 × 10−3 kg/m·s) is flowing steadily in a 5 -cmdiameter, 20-m-long circular stainless steel pipe. Determine(b) for an average velocity of 0.5 m/s, calculate the pressure drop, the head loss, the pumping powerrequired to overcome this pressure drop.
Water in a partially filled large tank is to be supplied to the rooftop, which is 8 m above the water level inthe tank, through a 2.5 cm internal diameter pipe by maintaining a constant air pressure of 300 kPa (gauge) inthe tank. If the head loss in the piping system is 2 m of water, determine the discharge rate of the supply ofwater to the rooftop in L/s. Show complete solution
Engine oil at 40°C (ρ = 876 kg/m3, μ = 0.2177 kg/m⋅s) flows in a 20-cm-diameter pipe at a velocity of 1.6 m/s. The head loss of oil for a pipe length of 130 m is (a) 0.86 m (b) 1.30 m (c) 2.27 m (d) 3.65 m (e) 4.22 m