Figure Q2 shows 8 cylinders Radial engine with their connecting rods are coupled to a single crank. The stroke is 180 mm and the length of each connecting rod is 270 mm. The mass of the reciprocating parts per cylinder is 1.2 kg. Determine the Primary and Secondary unbalanced forces and couple (if any) acting on the frame when the engine is running at 1,800 rpm. Explain briefly why the couple inertia does not exist in radial engine. 8 7 HOE wwwwwwwww 6 5 Figure Q2 2 3

Figure Q2 shows 8 cylinders Radial engine with their connecting rods are coupled to a single crank. The stroke is 180 mm and the length of each connecting rod is 270 mm. The mass of the reciprocating parts per cylinder is 1.2 kg. Determine the Primary and Secondary unbalanced forces and couple (if any) acting on the frame when the engine is running at 1,800 rpm. Explain briefly why the couple inertia does not exist in radial engine. 8 7 HOE wwwwwwwww 6 5 Figure Q2 2 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 200 kg at the crank pin, and the reciprocating masses per cylinder to 300 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the value of variation in tractive effort at 300 rpm. Select one: A. ±58476 N B. ±69780 N C. ±79654 N D. ±12475 N
A three cylinder radial engine driven by a common crank has the cylinders spaced at120°. The stroke is 138 mm, length of the connecting rod is 252 mm andthe mass of the reciprocating parts per cylinder is 2.2 kg. Calculate the primary and thesecondary forces at crank shaft speed of 1500 rpm.
The equation of the turning moment diagram for the three crank engine is given by:where θ radians is the crank angle from inner dead cen?tre. The moment of inertia of the flywheel is 400 kg-m2 and the mean engine speed is 300 r.p.m. Calculate the power of the engine and the total percentage fluctuation of speed of the flywheel, if 1. The resisting torque is constant, and 2. The resisting torque is (25 000 + 3600 sin θ ) N-m.
The ABCD structure illustrated on the left is used to stop the rotational movement of an inertia wheel attached in O while having a cusion B in contact with the wheel. The static friction coefficient is 0,4 and the cinetic friction coefficient is 0,3. The couple M applied on the inertia wheel is 300N*m. The lineic weight of the ABC membrane is 200N/m. The effort of compression in the hydraulic cylinder CD is 3,50 kN and its weight is negligible. Determine: 0.6 m a) if the inertia wheel turns or not b) the efforts on the ABC part 1 m 30° B 60 mm A M 0.3 m
Q2/ The six cylinder of a single- acting, two-stroke cycle Diesel engine are pitched 1 m apart 300 mm and the ratio of and the cranks are spaced at 60° intervals. The crank length connecting rod to crank is 4.5. The reciprocating mass per line is 1.35 Mg. The speed is 200 rev/min. Show with regard to primary and secondary balance, that the firing order 1-5-3-6-2-4 gives unbalance in primary moment only, and the order 1-4-5-2-3-6 gives secondary moment unbalance only. Compare the maximum values of these moments, evaluating with respect to the central plane of the engine.
Q6:- The firing order in a 6-cylinder, 4-stroke, in-line engine is 142635. The piston stroke is 100 mm and the length of each connecting rod is 200 mm. The pitch distances between cylinder center lines are 100 mm, 100 mm, 150 mm, 100 mm and 100 mm respectively. The reciprocating mass per cylinder is 1 kg and the engine runs at 3000 rpm. Determine the out o balance, primary and secondary forces and couples on this engine.
Q/A circular disc of mass m and radius r is Qil 'connected to two springs. If it is free to roll onarough horizoutal surface without_slipping, use energy methad to calculat the System natural Trequency.
B r P F A UBC Engineering Your team is prototyping a simple braking system for your model car. The 3.4 kg wheel with a radius of r = rad 0.15 m is rotating at w = 18 - .A servo motor can apply a variable force F, which in its first two seconds of operation is equal to F = 10t N and afterwards is equivalent to a constant force of F = 20 N . If the coefficient of kinetic friction between the braking arm and the wheel is μ= 0.2, determine the time needed for the wheel to come to a full stop. The point of contact P between the wheel and the arm is a distance r = -0.2 + 0.26 ĵ m from point A. The force of the servo motor is applied at exactly half of the horizontal distance to A from the point of contact. Assume the wheel can be treated as a disk and that the braking arm is massless. t =
A shaft has three eccentrics of mass 1kg each. The central plane of the eccentrics is 50 mm apart. The distances of the centers from the axis of rotation are 20 mm, 30 mm, and 20 mm and their angular positions are 120 degree apart. Find the amount of out-of-balance force and couple at 600 rpm. If the shaft is balances by adding two masses at a radius of 70 mm and at a distance of 100 mm from the central plane of the middle eccentrics, find the amount of masses and their angular positions. (Use graphical method for solution)
A flywheel weight = 50 kN with radius of gyration= 1 m losses its speed from 400 rpm to 280 rpm in 5 minutes. Find change in angular momentum.
B The shaft shown in the figure rotates at a constant speed of 1500/π rpm. Three masses rotating with the shaft are connected to the shaft as shown in the figure and cause instability. dynamic balance Determine the positions and values (kg.mm) of the masses that must be added to the DI and DII planes to ensure
Flywheels are used to smooth out fluctuating torques such as produced on the crank of piston engines. The diagram shows a torque - angle diagram for a certain machine. The speed of the shaft must be maintained between 490 and 510 rev/min. Calculate the moment of inertia of a suitable flywheel. Calculate the mass required if the radius of gyration is to be 0.3 m.