Figure Q5 shows the cross-section of the typical layout of two tracks (A and B) on a printed circuit board with a ground plane C. The tracks are terminated as shown in the figure, with track A carrying digital signals. You can assume that the lines are electrically short. Draw the equivalent circuit that models the crosstalk and write down a relation between the voltage applied to track A and the voltage coupled on to track B at low frequencies, VNE- (a) (b) If the total mutual inductance between the two tracks L =9 nH, and the total mutual capacitance between the two tracks is C = 2 pF, calculate: alitud

Figure Q5 shows the cross-section of the typical layout of two tracks (A and B) on a printed circuit board with a ground plane C. The tracks are terminated as shown in the figure, with track A carrying digital signals. You can assume that the lines are electrically short. Draw the equivalent circuit that models the crosstalk and write down a relation between the voltage applied to track A and the voltage coupled on to track B at low frequencies, VNE- (a) (b) If the total mutual inductance between the two tracks L =9 nH, and the total mutual capacitance between the two tracks is C = 2 pF, calculate: alitud

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter7: Symmetrical Faults

Section: Chapter Questions

Problem 7.21MCQ

See similar textbooks

Similar questions

A final year project student, Raphael, learns in EEE307 that an oscillator circuit with a differential output can be built using single-ended tuned amplifiers like the one shown below: VDD C₁=R4₁ - Vout VinM₁ Fig. 3.1 Single-ended tuned amplifier schematic (image adapted from B. Razavi ©2012)
What is load curve
Briefly describe the trade-offs between ripple adders and adders with carry look-ahead.
What is the ripple factor and what causes it? Discuss and explain how this factor can be used as a metric to improve the quality of the designed AC to DC converting system
does line current need Vrms or the given peak voltage to be solved?
Write an 8051 ASM program to load the timer 1 in order to generate 2000 Hz square wave as given in Figure. The square wave should be generated on pin 2 of port 3. Assume the crystal frequency is 16 MHz. ON 4* Delay Delay
An ac LVDT has the following data; input 6.3V, output 5.2V, range ±0.50 cm. Determine: a) Plot of output voltage versus core position for a core movement going from +0.45cm to -0.03cm? b) The output voltage when the core is -0.35cm from the center? c) The core movement from center when the output voltage is -3V? d) The plot of core position versus output voltages varying from +4V to -2.5V.
The value of critical clearing angle can be directly determined by using step by step method.Select one:True fals
Circuit breaker usually operate under A) after D. C. component has ceased B) transient state of short-circuit current C) sub-transient state of short-circuit current D) steady state of short-circuit current
In a communication system the signal sent from point a to point b arrives by two paths in parallel. For path 1, the signal passes through two repeaters ( in series ). Each repeater has probability of failing ( becoming an open circuit ) of 0.1. For path 2, the signal passes through one repeater with a probability of failing of 0.08. All repeaters fail independently of each other. Find the probability that the signal will not arrive at point b. O 0.0152 O 0.016 0.008 0.09
What advantages could the Network Laws have over the simple Series andParallel Circuits?
Q2:- By using IC 74151 Construct the following Function: F(A,B,C)= Eodd no.-1