Answered: Find the force P which is applied on…

Name: Find the force P which is applied onpoint B of the triangle ABC, as*
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Find the force P which is applied onpoint B of the triangle ABC, as* :shown in the figure belowP=? -BT = 600 N5 mC/609D-2.5m-P=216.7N OP=226.7NP=206.7N O

Engineering

Mechanical Engineering

Find the force P which is applied on point B of the triangle ABC, as :shown in the figure below P=? B y T = 600 N 5 m, L. C/60 -2.5m- P=216.7N O P=226.7N O D-206 ZN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the force P which is applied on point B of the triangle ABC, as :shown in the figure below P=? B T = 600 N 5 m Aa CA60 -2.5m- P=216.7N P=226.7N P=206.7N
with the following modifications: Add an additional force P = 20kN acting downwards at point B
A tower of 20 m, height is supported by three ropes shown in figure below. If the force of AB Is 50 N, find the force of AC and AD so that the resultant force should be vertical. A (0, 20, 0) Fa 20 m D(-8.0. 0) 50 N C (8,0, -10) B (8. 0, 5)
QS: The forces F1-6 kN, F2= 5 kN, and F3- 8 kN as shown in the Figure below, all of which act on point A of the bracket, are specified in three different ways. Determine the x and y scalar components of cach of the three forces. F500 N 35 4. 02m- F 800 N
Calculate forces (moments if applicable) for all points shown and write them down in a table. 1200N 100cm B- 100cm to OD- 100cm 100cm E O -2.4m-
9 - In the cage system connection in the figure; Rod forcesS1 = 100 kN,S2 = 40 kN,S3 = - 60 kN,S4 = 50 kN,If S5 = 80 kN, Calculate the resultant force acting on joint D.If the vector representation of the resultant force is R = Rx i + Ry j, Ry =? Note: The (-) sign of the bar force S3 indicates that the force is pressure. A) 12.93B) 3.64C) -36.36D) 27,07E) -12.93
92: The screw eye in figure below subjected to two forces F, and F,. Determine the magnitude and diredion f the resultant force using the Cosine law . Law• F=150 N Fi 100 N 15 "
4. Forces F =F-20N and the third force F3 25N act on a cube with the side of a=2m. a. Find the screw driver (wrench) that is created by these forces i.e pitch, Mparallel, Mpapendicular b. Find the point of intersection of the axis of the wrench with the x-y plane. How do you check your answer is correct? G F D A B.
(٢٦+ * Find the two forces Fbc & Fac as :shown in the figure below Fab=30 N 110 30/Fbc (Fbc=45.18 N and Fac= 58.8 N) O (Fbc=38.56 N and Fac= 56.38N) O (Fbc=75.18 N and Fac= 78.8 N) O ! Fac
2. The center diagonal of the truss in the figure shown can support tension only. Compute the force of DG and BE. A 20 200 B BD 200 BE COLORED СЕР TR1 D R18 DF F 250 www C000 20 E 15 EG M DG 600 20 G 15 600 300 H R3 R2
НОМE WORK 3 Determine the resultant force at A. for the figure below Hint : 1- Find the position of all points A,B.C (x, y., z) 2. Find Fas und FAC 3. Find Tanl and Iracl 4. Find FAg = F UA and Fac = F UAC 5- Finally find R and a, B.y 3m Fc= 500N FB= 500N 3m 5m 3m B 2m 4m 5m
What would be the resultant force F of the triangular distributed load and its location d measured from point A. 150 lb/ft -3 ft < 5 ft 2 ft Select.one: a F-375 Ib and d = 1.67 ft b.F=300 lb and d = 2.5 ft OcF=37S Ib and d = 3.67 ft id F=750 lb and d = 3.67 ft