fo = 39.69 Hz 5. Calculate the resonance frequency fo of the circuit when the resistance R1 is connected in series with inductance Ll. NOTE: Show the complete solution and attach to the file. IL- 7. Still at resonant state based on item 5, measure the currents IL, IC, component ILsin®, and the total current I of the cireuit. Also determine the value of impedance Z by taking the ratio of V and I in item 7. IC ILsin® A A

fo = 39.69 Hz 5. Calculate the resonance frequency fo of the circuit when the resistance R1 is connected in series with inductance Ll. NOTE: Show the complete solution and attach to the file. IL- 7. Still at resonant state based on item 5, measure the currents IL, IC, component ILsin®, and the total current I of the cireuit. Also determine the value of impedance Z by taking the ratio of V and I in item 7. IC ILsin® A A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

FAIRCHILD Discrete POWER & Signal Technologies SEMICONDUCTOR ru 1N4001 - 1N4007 Features • Low torward voltage drop. 10 a14 * High aurge eurrent cepablity. 0.160 4.06) DO 41 COLOR BAND DGNOTEs CAT-Cos 1.0 Ampere General Purpose Rectifiers Absolute Maximum Ratings T-26*Cuness atnerwioe rated Symbol Parameter Value Units Average Recttied Current 1.0 375" lead length a TA - 75°C Tsargei Peak Forward Surge Current 8.3 ms single halr-sine-wave Superimposed on rated load JEDEC method) 30 A Pa Total Device Dissipetion 2.5 20 Derste above 25°C Ra Tag Thermal Resistence, Junction to Amblent 5D Storage Temperature Range 55 to +175 -55 to +150 Operating Junetion Temperature PC "These rarings are imithg valuee above whien the serviceatity or any semiconductor device may te impaired. Electrical Characteristics T-20'Cunieas ofherwise roted Parameter Device Units 4001 4002 4003 4004 4005 4006 4007 Peak Repetitive Reverse Vellage Maximum RME votage DC Reverse Voltage Maximum Reverse Current @ rated VR…
4. An RC filter stage (R = 33 0, C = 120 HF) is used to filter a signal of 24 V dc with 2 V rms operating from a full wave rectifier. Calculate the percentage ripple at the output of the RC Section for a 100-mA load. Also calculate the ripple of the filtered signal applied to the RC stage. *****END*****
Date 03175996 28) A battery of emif 4V and grternal. xesistance 2n s joined to a desistor of 8 2 calculate the terminal potential difference. What additional xesistance in sedies with 8-2 sesistor Would produce a texminal pd of 3.6V? Taacher's Signalure
Repeat example 35 for FWD and firing angle Fa) 60°. 215 l65 D1985 Example 35: A full wave rectifier used 220V, with firing angle 10° ,total resistance load 5 KQ, inductance 2.34 H,and frequency 60HZ, Draw and calculate: (a) VD.c and Ipc (b) VD.C(Max) (c) Vn (d) Vorms-
For the circuit in the figurea) Determine the time constant.b) Write the mathematical expression for IL, VL and VR, after the switch is closed.c) Determine IL, VL for one, three and five time constants.d) Draw the waveforms of IL, VL and VR.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
GIVE DETAIL EXPLAIN PLEASE! with cicruit drawing.. Ans : Rth = 28 ohm Vth = 92 V.
R2=1kiloOhm, Voltage Source=10Vpk at 1kHz frequency, R3=1kiloOhm and zener diode has 5V breakdown potential R1 www 1k0 D1 Vo V1 5V 10Vpk 1kHz R2 1k0 a.) Plot the Output Waveform Vo. b.) Explain the output waveform at + input cycle. c.) Explain the output waveform at - input cycle.
3. Graphical Representation of the signal 1) Write the type of the voltage from simulation results: 2) Write the value of the voltage from simulation result: L....... -2 DDU 12ns SónG Trace Color Trace Name X Values CURSOR 1,2 V(R1:1,0) Y1 Y2 Y1 - Y2 5.0373m 0.000 5.0373m 249.983 0.000 249.983 Y1(Cursor1) - Y2(Cursor2) Y1-Y1(Cursor1) Y2 - Y2(Cursor2) Max Y Min Y Avg Y 249.983 0.000 0.000 249.983 0.000 124.991
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
a full-wave rectifier with a capacitor-input filter provides a dc output voltage of 35V to a 3.3k ohms load. Determine the minimum value of filter capacitor if the maximum peak-to-peak ripple voltage is to be 0.5V.
LTE .!!: 0:00 docs.google.com a What will be the out put of the D'Arsonval meters, if an average responding a.c meter of half-wave rectifier read (2.36 v), and true form factor of input waveform is (1.414). 3 volt 1.5 volt 1 volt 2.36 volt If the value of waveform does not remain constant with time, the signal is referred to as direct (d.c) signal * True False •.. 6 +