For a LEHI material, the principal plane stresses and associated strains in a plane at a point are o,=36 ksi, 02=16 ksi, ɛ1=1.02 x 103, and E2=0.18 x 103. Determine the Young's modulus and Poisson ratio of the material. Hint: use the equations for principal stress for 2D plane stress for LEHI, and consider 02/01.

For a LEHI material, the principal plane stresses and associated strains in a plane at a point are o,=36 ksi, 02=16 ksi, ɛ1=1.02 x 103, and E2=0.18 x 103. Determine the Young's modulus and Poisson ratio of the material. Hint: use the equations for principal stress for 2D plane stress for LEHI, and consider 02/01.

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

An axial load Pis applied to the rectangular bar shown. The cross-sectional area of the bar is 216 mm?. Determine the normal stress perpendicular to plane AB and the shear stress parallel to plane AB if the bar is subjected to an axial load of P = 77 kN. Assume a = 61°. B Answers: The normal stress o = i MPа. The shear stresS T = MPa.
Problem 11: Suppose a vertebra is subjected to a shearing force of 540 N.Randomized Variablesf = 540 Nh = 2.9 cmd = 4.3 cm Find the shear deformation in m, taking the vertebra to be a cylinder 2.9 cm high and 4.3 cm in diameter. The shear modulus for bone is 80 • 109 N/m2.
A 8-mm-thick rectangular alloy bar is subjected to a tensile load P by pins at A and B, as shown in the figure. The width of the bar is w = 35 mm. Strain gages bonded to the specimen measure the following strains in the longitudinal (x) and transverse (y) directions: & = 740 με and ε,- -270 με. (a) Determine Poisson's ratio for this specimen. (b) If the measured strains were produced by an axial load of P = 16 kN, what is the modulus of elasticity for this specimen? P B Answers: (a) v= i (b) Е- i GPa
A fishing rope of length (74+ 50) m has the diameter (74 + 5) mm. When a weight of (74 +200) N is hung on the rope, the extension is (74 + 50) mm. Calculate,i. cross-sectional area of the fishing ropeii. strain
PROBLEM 2. The light rigid bar ABCD shown in Fig. P-252 is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the load P = 41. 29 KN is applied. Hint: convert the distance of each member into mm, area of steel and aluminum into mm^2, & E into MPa.. Steel L-3 ft A- 0.5 in E- 29 x 10° psi 4 ft Aluminum L-4ft A- 0.75 in E - 10 x 10 psi + 2 ft Figure P-252
A copper (shear modulus 4.2 x 1010 N/m²) cube, 0.442 m on a side, is subjected to two shearing forces, each of magnitude F = 3.70 x 10°N (see the drawing). Find the angle (in degrees), which is one measure of how the shape of the block has been altered by shear deformation. r Number Units O
The elastic portion of the tension stress- strain diagram for an aluminum alloy is shown in the figure. The specimen used for the test has a gauge length of 50 mm and a diameter of 12.5 mm. The shear modulus is Gal = 28 GPaGPa. (Figure 1) If the applied load is 49 kN, determine the new diameter of the specimen. Express your answer to THREE DECIMAL PLACES σ (MPa) 500 0.00614 € (mm/mm)
The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Using Mohr’s circle, determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle θp, the principal strain deformations, and the maximum in-plane shear strain distortion in a sketch.εx = 0 με, εy = 350 με, γxy = 210 μrad. Enter the angle such that -45° ≤ θp ≤ +45°.
The bonded single lap joint shown below has a width, w = 97 mm and an overlap length, I = 28 mm. It has an applied tensile load, F. of 4385 N and a layer of adhesive h = 1.1 mm thick between the two members. The shear modulus of the adhesive is G = 3.7 GPa. W x-direction (a) What is the shear strain in the adhesive? Give your answer in radians, to 2 s.f. Shear strain: rad (b) Assuming that there is no deformation in the wooden sheets, what is the displacement of the upper plate in the x-direction? Give your answer in millimetres, to 2 s.f Displacement: mm
The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Determine the principal strains, the maximum in-plane shear strain, and the absolute maximum shear strain at the point. Show the angle θp, the principal strain deformations, and the maximum in-plane shear strain distortion on a sketch. εx = -750 με, εy = -345 με, and γxy = 1250 μrad. Enter the angle such that -45°≤θp≤ +45°.
i In. V:Y homewo... > Homework Ql: A specimen made from Titanium with diameter 4 mm subjected to force of 2500 N. The specimen extended by 0.422 mm. If the young modulus is 107 GPa. Find the gauge length of specimen. Q2: A road of stainless steel subjected to a tensile test, and the following result were obtained. Yield load = 175 KN and extension = 0.33 mm Max, Joad = 315 KN and max. extension 7.4 mm Original dia. = 16 mm and breaking dia. = 12.4 mm Original length = 80 mm Find: 1-Max. tensile strength 2-Young modulus 3-Percentage of elongation 4- Percentage of reduction in area II >
If the volume of liquid decreases by 0.5% for an increase of pressure from 9751987 N/m² to 251000 kN/m², calculate the bulk modulus of elasticity of the liquid. Please answer in SI unit (even temperature) with no decimals.