For your final design project, you use a keyway to hold your gear on the shaft. The radius of the shaft (r) is 3/16 inch and the torque transmitted is 1.78 lbf in. If your key is 0.0625 inches long (L, distance into page in left image), what must the width (w) be so that the acrylic key with yield strength of 5000 psi does not yield under the conditions above? Shear plane Torque Shear plane Center point O

For your final design project, you use a keyway to hold your gear on the shaft. The radius of the shaft (r) is 3/16 inch and the torque transmitted is 1.78 lbf in. If your key is 0.0625 inches long (L, distance into page in left image), what must the width (w) be so that the acrylic key with yield strength of 5000 psi does not yield under the conditions above? Shear plane Torque Shear plane Center point O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A pair of iron cast gears connecting two shafts at the Angle of the elbow. The diameter of the pinion pitch and the gear is 80 mm and 100 mm. The shape of the gear gear was 14 restriction form. The static voltage allowed for both gear is 55 mpa. If the door transports to 2.95 kw power at the turn of 1200 RPM, identify the module and the number of teeth on each gear from the Angle of power and check the design from the Angle of the tear. Take the surface durability limit is 630 mpa and the modulus elasticity to iron cast is 84 kn /mm2.
Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The pressure angle is 20° with a module = 2 mm. Determine the following: a. Draw the free body diagram for the gear set. b. Pitch diameters of each gear. 50T of m b. 3 30T - 20T C. Transmitted load on gear 2. d. Torque on gear 2 shaft a. e. Tangential and radial force from gear 2 shaft. f. Tangential and radial forces on gear 4. g. Torque on gear 4 shaft c.
A Design of Single Reduction Spur Gearbox An input shaft connected to the motor rotates at 1200 rpm, while the output speed must be 570 rpm. The contact force between the gears is transmitted through the pressure angle of 20°. The radial force is 321,90 kN. The material for both gear and pinion is 817M40. 1.1) select the suitable gear and pinion (make use of the Lewis formula). Then, do one set of calculations for single reduction gearbox
A power of 25 KW is transmitted by a pair of spur gears. Pressure angle= 20, radial force generated is 220 daN, the first gear speed is 600 rpm and the number of teeth is 33, the rotation ratio is 3 and the pitch diameter of the second gear how much?
A 63.5 mm shaft having a yield point of 50 ksi with a ¾ inch width key. Compute the length of key in order to transmit the torque on the shaft. The shearing stress of key is 22 ksi and use factor of safety of 2. (Ans: 3.72 in)
DRAW A GEAR NOMENCLATURE Given: Module of the Gear is 30mm. Number of Teeth is 20. Thickness of the Gear is 80mm. Find the Following: a. Root Diameter, Reference DIameter, TIp Diameter b. Addendum, Dedendum c. Pressure Angle, Base Diameter d. Tooth Thickness, Tooth Depth Draw a complete and detailed sketch Show complete solution Write eligible
You have been asked by your engineering company to design a complete gear and shaft system shaft that is made of steel. The solid shaft is linked with gear A, B. C and D with gear A., B and C produces torque of 15 kNm (clockwise), 30 kNm (clockwise) and 75kNm (anticlockwise). respectively each. If AB = 0.70m, BC= 0.80 m and CD=0.90 m with the shafts consist of solid circular shafts with a diameter of 150 mm having the shear modulus of G = 80 GPa, b) The shafts are now to be redesigned by drilling only through shaft BC with a diameter hole, cz to produce a hollow shaft BC. It is also known that the allowable shear stress, Tall in the shaft must not exceed 85 MPa. i) Determine the minimum wall thickness of the shaft BC, tBc
Hello, I hope you can help me. I'm trying to create a device that has a spinning axle and I need to change the rotational force to be perpendicular to the axle. I know there are gears that can fit together have teeth, like the attached picture. I know there are other types of mechanisms, and some are more creative. But I also need for the solution to be low friction. What are 2 low friction methods of changing the directional rotation of a power axle 90 degrees? The entire creation is small, probably 12" x 12" Thanks for your help.
Objective: Dimensional comparison between straight tooth gears and helical cylindrical gears. Calculate and compare the following gears: 1- Cylindrical Straight Teeth Gear: Z=18 m=3 2 - Helical Gear: Z=18 m=3 Propeller Angle: 20 degrees 3 - Helical Gear: Z=18 m=3 Propeller Angle: 30 degrees *Compare Outer Diameter and Primitive Diameter.
7. A typical drive train for a 'geared' bicycle meant to be used on paved road (see a representative image) has 48 teeth on front sprocket (Crank side), the diameter of front sprocket being 10.5 inches. The rear wheel has a cassette with a cluster of 6 sprockets, with number of teeth on Sprocket #1 (lowest gear) to Sprocket # 6 (highest gear) being 30, 26, 23, 20, 16 and 12, respectively. (Ignore wind resistance and friction between machine elements) (a) If the rider is pedaling at a constant 105 rpm with an effective force of 28 lb acting on periphery of front Sprocket (at 5.25 inch radius length, the force location indicated by red arrow), and is engaged in Sprocket #5, what would be the torque acting on Sprocket # 5, and the RPM at which the rear wheel is spinning? (b) For the condition as described in (a), If the diameter of wheels is 26 inches, what is the speed of the bicycle? &
In a single-stage gear wheel system with an evolvent profile, the rotating (driveThe number of teeth of the gear is Z1=10, the number of teeth of the rotated gear is Z2=20 and the modulus is m=5 mm; The rotating gear rotates clockwise.a) By calculating gear sizes; Draw in 1:1 scale.
A helical gear of 10 inches pitch diameter has a helix angle of 25 degree, and there are 35 teeth. The gear transmits 40 hp and rotates at 450 rpm with a normal pressure angle of 20 degrees. Find the Radial force.