Gate AB is subject to fluids on both sides as shown. Determine the following parameters considering a unit width (1 m) of the gate. For the water side: (a) A (m²), (b) (m), (C) F (KN), For the glycerin side: (d) A (m²), water Glycerin (SG = 1.26) (e) (m), (f) F (kN), and (g) What is the magnitude net hydrostatic force Ft (KN) on the gate? 1.8 m 1.2 m 2.0 m 2.0 m 1.0 m gate

Gate AB is subject to fluids on both sides as shown. Determine the following parameters considering a unit width (1 m) of the gate. For the water side: (a) A (m²), (b) (m), (C) F (KN), For the glycerin side: (d) A (m²), water Glycerin (SG = 1.26) (e) (m), (f) F (kN), and (g) What is the magnitude net hydrostatic force Ft (KN) on the gate? 1.8 m 1.2 m 2.0 m 2.0 m 1.0 m gate

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A and B are cross-sections of two pipes with water flowing. These pipes look like To measure the pressure difference between A and B by connecting a U manometer is requested. The heights in the U manometer are given in inches (1 inch=25.4mm). Since Moil=850 kg/m3 and 'mercury=13600 kg/m3 A- Find the pressure difference B. B Oil 8 -H20 10 H20 4 3 Hareketli plaka -Hg-
Q1/ A piston pushes down on a volume of hydraulic oil ISO 68, trapped in a cylinder, its bore is 10cm, and the height of the unstressed column of oil is 50cm. The oil has a bulk modulus B=2.2 *105 psi. When a force of 2500N is applied to the piston. How much does the piston displace? Note : (The ISO 68 has a density of 54.9 Ib/ft(880 kg/m³)
Select the correct value of H: ( The density of liquid =990 kgim, gravity g = 9.81 mis and L= 90 cm, Pressure P1= 52.369 Kpa) Air Pt Liquid (2)
For the manometer shown in the image, all fluids are at 20°C. If PB- PA = 90 kPa, determine the height H in centimeters. The specific weight of water is 9790 N/m³ and the specific weight of mercury is 133100 N/m³. Meriam red oil, SG = 0.827 Water 18 cm H 35 cm Numeric Response B Mercury
The sketch shows an oil manometer that is connected between two pipes which transport water. The density of water can be taken as 998kg/m3, the specific gravity of glycerol is 0.76 and atmospheric pressure is 100 kPa. The respective dimensions (as shown on the sketch) are given below: h1 = 0.17 m h2 = 350 mm h3 =15cm. From the given data, calculate the pressure difference between the two pipes.
Here are these questions if I could get help with themIf a spherical storage tank holds 40,000 gallons (120,000 liters) of water,what diameter must it have?If a cylindrical storage tank has a 40-foot (12 m) diameter circular 05::=how high must it be to hold 1 million gallons (3 million liters)?If water is moving at a rate of 3.2 ft3/sec (90,000 cc/sec), how manygallons (liters) per minute is this?If the specific gravity of gold is 19.0. what is the weight of a cubic inch(cubic centimeter) of gold? A cubic foot (cubic meter)?
1.The density p Determine how the density varies with pressure along the depth h. The density at the surface of the fluid is of a fluid varies with depth h, although its bulk modulus K can be assumed constant. Po. 2.A circular disc of diameter (D) is slowly rotated with angular velocity of ( wi) in a liquid of large viscosity (u) at a small distance (h) from another moving disc at counter clockwise rotation of (w2), as shown in figure (2). Derive an expression of torque (T) necessary to this case. D Figure (2)
You are being asked to determine the heights in tubes B and C (relative to z=0) given the following information: The specific weight of Air is Pair = 11.9N/m3 The specific weight of glycerine is Paiye = 12355N/m3 The specific weight of gasoline is Pgas = 6677N/m3 The gauge pressure at A is Pa = 1.6kPa The height of the tank of air is a = 1.7m The height of the tank of gasoline is y = 1.6m The height of the tank of glyercin is k = 0.95m A в с xm Air y m Gasoline k m Glycerin z = 0 As a HINT, you do not need to know the specific elevations of the tubes B and C entering their respective fluids, but you do need to account for this. Input the height the fluid rises in B to 2 decimal places here: (in metres) Input the height the fluid rises in C to 2 decimal places here: (in metres)
Estimate the capillary depression in mm for mercury in a glass capillary tube 2 mm in diameter. Use o = 0.514 N/m and e = 140° Choose the correct answer below O -5.9 mm O -6.2 mm -3.5 mm O -7.0 mm
A tank is filled with fluid under prcssurc anti the prcssurc gauge fixcd at the top indicatcs a prcssurc of 21 kPa. The curved surfacc of the top is quarter of a circular part of radius 2.6 m. calculate the magnitude (N) and direction (degree) of the resultant force on the cun'ed surface. (p=950kg./m³for fluid)
Round off at the final answer only! As illustrated, the semicircular gate AB is utilized to store kerosene. In meters, how far is the center of pressure from A? Kerosene SG= 0.82 5 m 3 m A B -P Gate: Side view
Fluid mechanics, I need solutions in 15 minutes please. MCQ/Determine the horizontal and vertical components of the liquid pressure acting on the semicylindrical gate ABC, as shown in the figure. The width into the paper is 1 m. A-Fx = 257.430 kN and Fy = 59.801 kN B-Fx = 164.018 KN and Fy = 37.229 KN C-Fx = 269.894 kN and Fy = 65.526 KN D-Fx = 98.182 kN and Fy = 20.002 KN E-Fx = 234.789 kN and Fy = 52.418 kN F-Fx = 187.005 kN and Fy = 42.182 KN G-Fx = 119.956 kN and Fy = 25.550 KN H-Fx = 141.327 kN and Fy = 31.171 KN I-Fx = 288.147 kN and Fy = 69.098 KN J-Fx = 213.112 kN and Fy = 47.903 KN