Give other methods of determining the horizontal distance between two points.

Q: Please provide your solutions and corresponding illustrations 1. Determine the angle in between two…

A: Bearing is the angle made by line either from north and south. Azimuth is taken either totally from…

Q: On a map of scale 1:75,000 the map distance measured between points A and B is 5.0 cm. If a sketch…

A: Find scale for sketch of same area

Q: If I want to draw a line in the direction 7:30 (local time) will give an angle -135 degrees 270…

A: A multiple choice questions is asked, please refer step 2 for detailed solution and explanation.

Q: Construct a diagonal scale of RF =1/2500 to show meter and long enough to measure upto 500 meter.…

A: Diagonal Scale: The diagonal scale is used to represent three units. The three units are the main…

Q: 51 35 88 73 53 15 20 25 „16 64 _15 38 75

A: Given isometric figure is,

Q: Map distance=5 cm Ground distance%3D2 km Determine scale

A: Given data : The value of map distance=5 cm The value of ground distance=2 Km   To find: Scale of…

Q: Write the units used by English systems to specify small areas?

A: Solution: In the English system, areas are basically given in square feet or square yards. For…

Q: What is the Global Coordinate System (GCS)? Why was the Viewing Coordinate System created?

A: Global Coordinate system is a coordinate system in which we are enabled to make a location details…

Q: Give a brief description: a. Measurement of Horizontal Distances b. Omitted Measurements c.…

A: Any plane which contains horizontal line and perpendicular  to the vertical direction is called as…

Q: write this question clearly plz

A: To find out the balanced moment capacity and area of steel Required.

Q: 3)The accompanying tabulation gives elevations of points over the area 20m by 20m city lot.The…

A: Contour: The imaginary line joining points of equal elevations on the ground surface is known as…

Q: List the different meridians are used to specify directions?

A: The direction of a survey line can be defined in two ways: Relative to each other  Relative to some…

Q: What are Bar Charts?

A: A bar chart is a method to summarize a collection of categorical data (by auto-binning continuous…

Q: Section lines are spaced from /16" to /8" or more apart. O True O False Section lines are normally…

A: Question 1 Solution: Section lines are usually drawn in order to understand the plane where the…

Q: FIND THE LENGTH OF THE DIVIDING LINE DP. THANK YOU. (THIS SUBJECT IS SURVEYING)

A:

Q: Discuss the procedure for performing 2D conformal coordinate transformations?

A: Solution: There are basically 3 steps that are used in the procedure of 2D conformal coordinate…

Q: Tell, how many AutoCAD objects are in a polygon? One object. Two objects.

A:

Q: A map is drawn to a scale of 1 : 500. What distance does 145 mm on the plan represent on the ground…

A:

Q: Give the vector in cartesian coordinates that extends from B(4, 20degrees, 10degrees) to W(7,…

A: The given data is shown below: B=4,20 degrees, 10 degreesW=7,120 degrees, 75 degrees

Q: 14.The polar coordinate of a point is (10, 60degrees). Convert to Cartesian coordinates.

A:

Q: What is National Spatial Reference System?

A: National Spatial Reference System  (NSRS) A consistent coordinate system that defines latitude,…

Q: How many divisions are on the vernier scale?

A: A vernier scale is a visual representation that uses mechanical approximations to obtain an exact…

Q: 3)The accompanying tabulation gives elevations of points over the area 20m by 20m city lot. The…

A: Contour: An imaginary line that connects the points of equal elevations on the ground surface is…

Q: determine back the missing data on blank lines

A:

Q: What is meant by a 2D conformal coordinate transformation?

A: 2-D Conformal transformations include two parameters for amendment in origin (or translation), one…

Q: Define Relative precision.

A: Relative precision:

Q: What is Planimeter?

A: Planimeter is defined as:

Q: Practical part: Q5) Draw the profile with horizontal scale 1:1000 and vertical scale 1:20, stations…

A: Given : Stations and their Elevations in metres. Horizontal scale = 1:1000 Vertical scale = 1:20…

Q: Draw or interpret the characteristics of Contours.

A:

Q: What are velocity charts?

A: The Velocity Chart displays the value amount delivered in each sprint so as to forecast the work…

Q: The Global Coordinate System (GCS) is an acronym for Global Coordinate System. What motivated the…

A: Global Coordinate System is an absolute reference system which is used to define locations of nodes…

Q: Figure 1 shows an orthographic projection of a block. Draw the object in isometric projection. Show…

A:

Q: Explain 1st and 3rd angle of projection

A: First angle projection and Third angle projection are two different methods of creating a 2D drawing…

Q: Practical part: Q5) Draw the profile with horizontal scale 1:1000 and vertical scale 1:20, stations…

A: Solution: Given: Station ,m Converted scale valuestation1000 Elevation, m Converted scale value…

Q: Tell, how many AutoCAD objects are in a polygon? One object. Two objects. Three objects. All the…

A:

Q: A line CD starting at any point, C, is 8 m long bears N 35° W, and slopes downward from C to D at…

A:

Q: Give 3 Civil Engineering problems using curve fitting and interpolation

A: It is asked problems using curve Fitting and Interpolation:   Curve fitting is to find a curve…

Q: Find the shortest distance from point B to line AC

A: x0OB=7j-3kx1OC=7j+5kx2OA=12i Shortest distance

Q: What is a geodetic coordinate system?

A: There are two coordinate systems for geographic data:- a) Geodetic coordinate system:- They are…

Q: 40 15 60 90 10 45 07 30

A: The Top view is:

Q: * aut cad To draw a horizontal line from right to left what direction would it be? 45 270 O 100 O…

A: AUTOCAD To draw a horizontal line from right to left what direction would it be?

Q: Give your OWN definition for Level Line, Horizontal Line, and Mean Sea Level(on leveling).

A: LEVEL LINE- Level surface is the continuous                              surface parallel to the…

Q: What is surveying

A: Surveying is the branch of civil engineering which deals with finding out and analysing various…

Q: Draw the plan and components of the given line diagram figure. Assume suitable data? W W. D. SITTING…

A: