Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 9 ohms R2 = 5 ohms C1 = 0.454 Farad C2 = 0.992 Farad Vs = 10,246 Volts Frequency = 70 Hz What is the Amplitude of the voltage across C1?

Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 9 ohms R2 = 5 ohms C1 = 0.454 Farad C2 = 0.992 Farad Vs = 10,246 Volts Frequency = 70 Hz What is the Amplitude of the voltage across C1?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 6RQ: A 15-F AC capacitor is connected in series with a 50 resistor. The capacitor has a voltage rating...

See similar textbooks

Related questions

Q: A multilayer coil of 2000 turns of fine wire is 20 mm long and has a thickness 5 mm of winding. If…

A: The EM wave is formed when electric field is in contact with magnetic field. Magnetic field exert…

Q: Q5: For the coupled circuit shown in Figure 3, find the voltage across the capacitor of -j102…

A: Taking KCL at VxVx-V15+j5+j2+Vx-V25+j5+j2+Vx-j10=0⇒Vx-105+j7+Vx-10∠905+j7-jVx10=0⇒2Vx-10-10j10 -…

Q: a) Some capacitors are marked 45micro farad save working voltage 25V. On a circuit diagram show how…

A: Given, Capacitor, C=45 μFIt is safe working with a voltage.Voltage, V=25 V

Q: O If the capacitor of Figure (2) has the value df on the circuit? Determine the time constant. Volt…

Q: A coil of resistance 82 and inductance 0.5 H is connected to 110 V d.c. supply. Find (i) rate change…

A: We have an coil of resistance and inductance with, Resistance (R) = 8 Ω Inductance (L) = 0.5 H…

Q: An uncharge capacitor in series with a 120 volt voltmeter of 10,000 ohms resistance is suddenly…

Q: Q2) Find the voltage and current for the capacitor ci figure 1 Q3) Find the voltage of L1 using mesh…

A: As per our guidelines we are supposed to do the 1st question only. Kindly repost the remaining…

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: a 9.0 V 50 Ω 2.0 μ |

A: Since, the capacitor doesn't allow the sudden change of voltage. Hence the voltage across the…

Q: A capacitor of value 100uF is connected across a 200 V, 50 Hz supply. Calculate : (i)reactance of…

A: We have an capacitor with, C = 100 μF = 100 * 10-6 F Voltage (V) = 200 V Frequency (f) = 50 Hz…

Q: The 0.5-nF capacitor of figure (1) has the waveform of current shown across it. Calculate and plot…

A: Current waveform is applied to the capacitance. Find the voltages waveform and power waveform.

Q: A8-cm long wire carying a uniformly distributed 12µc charge is bent into a semicircle. What is the…

A: Given that, length of wire=8 cm,Q=12μC when it is bent into semicircle, for cemi-circle having…

Q: An inductor of L = 500 mH and R = 100 ohms passes a current of i = 4sin(500t) A. What is the voltage…

Q: If you have circuit with two capacitors C1=400 uF, C2= 200uF and voltage 120 V. Calculate

A: The solution can be achieved as follows.

Q: Consider that four capacitors are connected in the combination of series-parallel with the power…

A: In this question, We need to determine the voltage across the each Capacitance? We know Charge…

Q: For the circuit in shown in figure 5, find the value for unknown capacitor C2

A: Given: Battery voltage E=333 V. Capacitor C1=12.5 μF, V1=8 V. Capacitor C2: Q=0.00113 C, V2 Volt.

Q: C1 1 µF R1 2 kΩ R3 2 kQ + VR3 + Vci + VRI I VR2 R2 1.5 k2 + L Vs 13520° 10 H V rms VL C2 1.5 µF 60…

Q: What is the inductive reactance of the following voltage source 200 sin(500t +30) V in series with a…

A: Given: Voltage source with voltage, vt=200 sin500t+30 V Series connected inductance value, L=10 mH

Q: ix 13 V mat drives Capacitor

A: Thevenin's theorem states that if a circuit containing an RLC components, independent voltage…

Q: 21. A current of 2.5 A flows through a series circuit consisting of a 100 N resistor and an unknown…

A: We need to find out capacitive reactance for given circuit

Q: The 0.5-nF capacitor of figure (1) has the waveform of current shown across it. Calculate and plot…

A: The current and voltage relation for a capacitor is given by i=CdVdt Hence, V=1C∫0ti(t) dt The…

Q: 2. A series combination of a resistor and capacitor absorbs 100 Wand -42 vars at 60 Hz. If R = 100…

Q: Three capacitors A, B and C are charged as follows: A = 10 µF at 100 V; B = 15 µF at 150 V; and C =…

Q: A 5-ohm resistor is connected in series with a 25 micro-farad capacitor. A source voltage of 158…

Q: QUESTION 2 Initially, the capacitors in the circuit in Figure 2 are uncharged. After the switch is…

Q: What is the Total Reactance in ohms?

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: Q2) Find the voltage and current for the capacitor C1 figure 1 22 mH 3 k Ohm 160 SIN(160t+55) 1 k…

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

A: Brief description: Capacitor is an electrical element which is used to store the charges. The charge…

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: Given the following Resistances and Capacitors in Series and Voltage Source: R1 = 6.946 ohms R2 = 9…

Q: Given the following Resistances and Capacitors in Series and Voltage Source: R1 - 7 ohms R2 = 4 ohms…

A: According to the question we have to find the value of the amplitude of the voltage across C1.

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: b) For the circuit as shown in figure 2, calculate the equivalent capacitance between a an 25 μF 25…

Q: 1. What is the equivalent capacitance of this combination? 2. What is the total charge in the…

A: The given circuit is,

Q: c) Some capacitors are marked 45micro farad save working voltage 25V. On a circuit diagram show how…

Q: A 40 micro-farad capacitor, 100 mH inductance and a 40 ohm resistor are connected in series. The…

Q: Mutual inductance between an infinite current filament placed along y -axis and rectangular coil of…

A: Find the mutual inductance between an infinite current filament placed.

Q: 2.2 μF capacitor to charge when connected in series with a 820 ohm resistor

A: Time constant is the time taken by the response to reach 63.2% of its final value while charging.…

Q: If a circuit has a resistance of 3002 and a series inductance of 5002, what is the relationship…

A: The solution is given below

Q: Three capacitors are connected in parallel and have the following voltage ratings: C1 = 32 uF with…

Q: A 50 and 100 microfarad capacitors are connected in series and across 100sin(w+30) voltage. Write…

Q: A capacitor of 20.0 µF and a resistor of 100 2 are quickly connected in series to a battery of 6.00…

A: The solution is given below.

Q: A 25 microfarad capacitor in series with the resistor R at a frequency of 60 Hz. The resulting…

Q: (A) 0.25 uF 10V 2uF 4uF (B) Figure 3: 3. In Figure 3 the capacitors were discharged before being…

A: NOTE: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question…

Q: A 10uF connected in series with a 200 ohms resistor is charged by a 12 V source. How long will it…

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

Given the following Resistances and Capacitors in Series and Voltage Source:
R1 = 9 ohms
R2 = 5 ohms
C1 = 0.454 Farad
C2 = 0.992 Farad
Vs = 10,246 Volts
Frequency = 70 Hz
What is the Amplitude of the voltage across C1?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.
An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a voltage drop of 65 volts. What is the capacitance of the capacitor?
With V1, voltage peak to peak is 10 volts, R1=200 Ohm, R2=1000 Ohm and C1= 300 nF. Find Vx, voltage across the the capacitor, C1 and R2 when the frequency is 1000 Hz and 10000 Hz
4) Determine the value of branch current, I1 and I25) Determine the value of voltage across resistor, R1, R2 and R36) Determine the value of voltage across capacitor, C1 and C27) Determine the value of voltage across inductor, L.
An LM317 is connected between two decoupling capacitors. There is a 220ohm resistor between the output pin and the adjust pin. Note the voltage drop between the output and adjust pins is 1.25V. Find the resistor needed between the Adjust pin and ground to ensure 5 V is dropped across the load. Enter your answer in ohms: _ohms
1. 1-5 K 30v a. what is tue T CTime constant) ? b. How long will it take for the capacutor TO rtach s0% op charge? C. What is tne voltage of capa citor apter 1 seconds? d. How many tíme constants will it take for the soltage to reach 23 v? C. Gweng that the capacitor is fully changed, how will it take por it to be 20% ? long 120v + BF what is the. T ? b. what is the voltage capacitor apter 10 sec? a. C. How many time constants will it take for Tue Vo Itage to reach 80 v.? d. Given that the capaator is Fully charged, how time constants will it be to reau many GOV!
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
this is electric circuit questin ...plz solve it early .plz solve early
What voltage is boosted at the output of a multiplier.Choices: average, rms, peak, or instantaneous Which assumption is not used in the analysis of multipliers?Choices: a capacitor will not discharge, start with the cycle of the source that will forward bias the nearest diode, the output will always be multiplied, or a single diode is forward biased at a time A voltage multiplierChoices: multiplies the output voltage, has very high voltage and low current ,can employ inductors, or may not have equal numbers of diodes and capacitors A voltage regulator maintains constant voltage at the load regardless of variations atChoices: the input and output, the load, source, or in the environment Between a lower percent regulation and a higher one, which is better?Choices: lower or higher
Calibri (Body) -11 by AaBbCcDx AaBbCcD AaBbC AaBbCc AaB AaBbCc. mat Painter BIU 1Normal 1No Spaci. Heading 1 Heading 2 Title Subtitle Chang Styles d Font Paragraph Styles IMPEDANCE QUIZ # 2 1. What capacitance when connected in series with a 500Q resistor will limit the current drawn from a 48-mV 465-kHz source to 20µA? * a. 144pF b. 145pF c. 146pF d. 147pF MY ANSWER: c.146pF 2. What is the total impedance at 20kHz of a series circuit consisting of a 1.5mH inductance, a 100Q resistance, and a 0.08uF capacitance? * a. 1340 41.7 b. 1930 L-37.2" C. 920 290 d. 530 2-12.6°
the shunt capacitance is a capacitor O a. Between a phase and the ground O b. between phases and a phase to ground c. none of the answers O d. Between phases