he bar clamp is being used to clamp two boards together while the glue between them cures. What torque M must be applied to the andle of the screw in order to produce a 68-lb compression between the boards? The 0.375-in.-diameter single-thread screw as 18 square threads per inch, and the effective coefficient of friction is 0.27. Neglect any friction in the pivot contact at C. What orque M' is required to loosen the clamp? M

he bar clamp is being used to clamp two boards together while the glue between them cures. What torque M must be applied to the andle of the screw in order to produce a 68-lb compression between the boards? The 0.375-in.-diameter single-thread screw as 18 square threads per inch, and the effective coefficient of friction is 0.27. Neglect any friction in the pivot contact at C. What orque M' is required to loosen the clamp? M

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

H.W A Solid Steel bar of dlameter 6omm and length 350 mm is Placed inside an aluminum cylinder öf Inside diameter Femm and out side d lameter Ilomm, a comPressive load of looo lais applied on the assembly, find the stresses in the bar and the cylinder ? take Est = 200GPa and EAl = F0GPan %3D Cover Plate 0.25mm d- do 35omm A lum. cylinder Steel bar
Student A B D H Number 201780130 2 1 7 8 1 3 Evaluate the following variables and use them as given in the following problems. 200 if I is even, 250 if I is odd (D + G)*10 (H + I/2, if in case the result is zero, use 3 (A +C + E)*2 (P + M)*20 H + 5 M Q %3D 50(E + G + 1) II II || || || |||| ZNPORX
One plate of size 100 mm x 12 mm is lap joined to another plate of size 200 mm x 12 mm by fillet weld of size 10 mm. Lap length is 100 mm. Fillet weld is provided on all the three sides of the smaller plate. Determine the maximum axial tension the joint could carry. Assume the plates are of mild steel of grade 250 N/mm?.
The two steel plates are bolted to the wooden beam shown by 30-mm-diameter bolts spaced at 200 mm. Knowing that beam is subjected to V 5000 N, and that the moduli of elasticity for steel and wood are 200 and 40 GPa, respectively. Determine: (a) Shearing stress in each bolt; and (b) shearing stress at the mid- height of the upper steel plate. 150 mm 12 mm 250 mm 12 mm Solution:-
A 22.2 mm diameter bolt having a diameter at the root of the threads of 18.6 mm is used to fasten two timbers as shown. The nut is tightened to cause a tensile load in the bolt of 34 kN. (a) Determine the shearing stress in the head of the bolt. (DRAW THE FREE BODY DIAGRAM) (b) Determine the shearing stress in the threads. (c) Determine the outside diameter of the washers if their inside diameter is 28 mm and the bearing stress is limited to 6 MPa. (DRAW THE FREE BODY DIAGRAM)
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesNOTE: Draw FBD(a) If we increase the diameter of each bar to 20 mm, determine the maximum load Pthat can be applied to the lap joint.(b) Using the value computed for maximum load P from (a) compute for the over-allfactor of safety given that the actual P= 20kN.
Connections Example: Calculate the strength of the single lap joint. The plates are made of 1"x4" wooden blocks with a 2" overlap. The glue can carry 125 psi in shear. The wood can carry an axial stress of 1000 psi. How much force P can the joint carry? Sketch and FBD P b a P
A 100 x 100 x 10 mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu = 483.33 MPa. Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. Determine the length of side fillet weld required at the heel. Determine the length of side fillet weld required at the toe.
Determine the shear Load that act on the fillet weld that joining two plates together if the working stress is 11300 Ib/in? Throat
Problem No 2 A flanged-bolt coupling consisting of six 4 inch diameter steel bolts evenly spaced around a bolt circle 12 inches in diameter and four inch diameter aluminum bolts on a concentric circle 8 inches in diameter. What stresses are developed on each bolt of the two bolt-circles when a torque T=75 Kip-in is applied. Use Gs=12 x 10° psi and GA = 4 x10° psi.
Solve for the EI A using conjugate, beam method 3m 50 kN 2m EID @ pt. C 60KN die 2.5m å
A flanged bolt coupling consists of six 1/2-in. steel bolts evenly spaced around a bolt circle 12 in. in diameter, and four 3/4-in. aluminum bolts on a concentric bolt circle 8 in. in diameter. What torque can be applied without exceeding 9000 psi in the steel or 6000 psi in the aluminum? Assume Gst = 12 x 10^6 psi and Gal = 4 x 10^6 psi.