I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075. The shaft is 960 mm in length, 40 mm OD and 20 mm ID. The threaded end of the shaft is M30X3.5. What would be the recommended torque for the shaft, with the dissimilar metals. I’m expecting a range between 100-280 ft-lbs but can justify it.

I have a 52100 steel hollow shaft, that will be threaded into a 1 inch thick plate of aluminum 7075. The shaft is 960 mm in length, 40 mm OD and 20 mm ID. The threaded end of the shaft is M30X3.5. What would be the recommended torque for the shaft, with the dissimilar metals. I’m expecting a range between 100-280 ft-lbs but can justify it.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I have a hollow shaft that has an OD of 40 mm and an ID of 20mm. The length of the shaft is 900mm. One end has a M30X3.5 outside thread. The shaft is made of 52100 steel. It has a tensile strength of 325 KSI. What would be the recommended torque for the thread, in (in-lbs)?
Calculate the maximum allowable torque (in-lbs). A solid steel shaft is made from AISI 1045 steel, with a 9.0" diameter and length of 44". The maximum allowable shear stress on the material is 6200 psi. Based on the answer above, what is the required RPM if this shaft needs to transmit 4500 HP at the maximum allowable torque?
I have a hollow shaft that has an OD of 40 mm and an ID of 20mm. One end has a M30X3.5 thread. The shaft is made of 52100 steel. It has a tensile strength of 325 KSI. What would be the recommended torque for thread, in in-lbs?
Please give proper solution.other wise skip to other expert I want to learn. shaft transmits 75 kW power at 300 r.p.m. The distance between the two bearing is 3000 mm. It is subjected to torsion only. Calculate the diameter of the shaft. (1) For steady loading.
Write legibly, provide manual step by step solution, and diagram for below given problem. A 1 in height x 6 in length flat keyed to a 5 inches diameter shaft. Determine the torque in the key if bearing stress allowable is 30 ksi. Ans. 225,000 in-lb
What would be the recommend torque and max torque for a hollow shaft made of 52100 bearing steel equivalent, that is M30x3.5-6H, threaded on one end. Length is 952 mm. Shaft diameter is 40 mm, inner diameter of 20 mm. Screwing into an aluminum 7075- t7351, plate that is 1 inch thick. The shaft would carry a load of 138 lbs, evenly distributed.
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 10 ft-kip 15 ft-kip 20 ft-kip CGGGG T 15 ft-kip
What would be the recommend torque and max torque for a hollow shaft made of 52100 bearing steel equivalent, that is M30x3.5-6H, threaded on one end. Length is 952 mm. Shaft diameter is 40 mm. Screwing into an aluminum 7075- t7351, plate that is 1 inch thick.
A circular shaft of 60 mm diameter is running at 150 r.p.m. What will be the torque transmitted by the shaft if (t = 80 MPa)?
For the steel shaft shown in Fig. Draw a torque diagram for the shaft. 17 ft kip 60 ft-kip 12 ft-kip 10 ft-kip 25 ft-kip
If the torque is 2270 Nm, what is the minimum diameter solid shaft (in mm) to keep the stress under 203 Mpa ? 42.05 mm O 15.73 mm 38.47 mm O 23.11 mm
A solid circular drive shaft connects a motor to gears B and C. The drive shaft is steel (G= 66 GPa) with a diameter of d=35 mm. 600 N-m A 200 N-m (1) (2) 100 mm C. 300 mm