If LM = 00, the next state of the flip-flop is 1. If LM = 01, the next state of the flip-flop is the same as the present state. If LM = 10, the next state of the flip-flop is the complement of the present state. If LM = 11, the next state of the flip-flop is 0. A sequential circuit contains a register of four flip-flops. Initially, a binary num- ber N (0000 < N < 1111) is stored in the flip-flops. After a single clock pulse is applied to the circuit, the register should contain the result of the expression (N – 5) mod 16. Design the circuit using the aforementioned LM flip-flops.

If LM = 00, the next state of the flip-flop is 1. If LM = 01, the next state of the flip-flop is the same as the present state. If LM = 10, the next state of the flip-flop is the complement of the present state. If LM = 11, the next state of the flip-flop is 0. A sequential circuit contains a register of four flip-flops. Initially, a binary num- ber N (0000 < N < 1111) is stored in the flip-flops. After a single clock pulse is applied to the circuit, the register should contain the result of the expression (N – 5) mod 16. Design the circuit using the aforementioned LM flip-flops.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

5. A sequential circuit has two flip-flops A and B, one input X, and one output Y. The state diagram is shown in the following figure. Design the circuit with D flip-flops using a 1-hot state assignment. 00/1 01/0 11/0 10/0
4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
Flip-flops are basic memory element used in sequential circuits. Flip-flop has two stable states – logic 0 or logic 1. A flip-flop will either be in one of the two stable states after application of the input signals; it will remain to be in that state even if the inputs are removed. Flip-flops are also known as the latch or toggle.(a) (i) What is the difference between D flip-flop and JK flip-flop. (ii) How will you convert a D flip-flop to J K flip-flop? (b) Realize the following function of three variables with 8:1 MUX. F (A,B,C) = ∑(0.1,3,4,7) (c) (i)kindly demonstrate, the difference between the output waveform of the output Q of D flip-flop and the Q of clocked R S flip-flop. AP(4marks)3(ii) How will you modify an asynchronous R S flip-flop so that when both the inputs R and S are 1, the flip-flop is set?
b) A sequential circuit is constructed with one T flip-flop A, one D flip-flop B and one input X, when X-0, the state of the circuit remains the same. When X-1, the circuit goes through the transitions from 00 to 01 to 11 to 10 back to 00, repeat. (i) Draw the state transition diagram (i) Construct the state Table (ii) Draw the circuit.
Design a sequential circuit with two D flip-flops and two input x and y. When x=0, the state remains the same. If x=1 and y=0, the circuit goes through the state transitions 00 to 01 to 10 to 11 then back to 00. When x=1 and y=1, the circuit goes through the state transitions 00 to 11 to 10 to 01 then back to 00. Include state table, state diagram, equation/s from the K-map (flip-flop input equation), and circuit diagram.
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K. 2-t0-1 MUX Y B' CLK
Question: The flip-flops in the drawing below are positive edge triggered D flip-flops. Let Q2, Q1, QO = 0,0,0 initially. a) Plot the clock, Q2, Q1 and QO until the outputs begin to repeat. b) Show the circuits acts as a counter 00 1000 Hz/50%
Design a sequential circuit with two flip-flops A and B, and one input x_in. When x_in = 0, the circuit goes through the state transitions from 00 to 10, to 01, to 11, back to 00, and repeats. When x_in = 1, the circuit will reverse the given sequence. a. Using D Flip-Flop. b. Using JK Flip-flop. Provide the state diagram, state table, state equations, and the circuit diagram.
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K B 2-t0-1 MUX B' K CLK
Design a 2-bit counter using D-Flip flops with one input. When the input is 0, the ww m wwww w w m w i ww ww wwww www counter counts down, with the repeated sequence (11-10-01-00). When the input is 1, the counter counts repeated random sequence (00-01-11-10). a) Derive the state table for the sequential circuit. wwwww b) Derive the simplified flip flops input equations. www w w ww www m www ww c)Draw the logic circuit diagram of a 2-bit counter.
DO NOT COPY ANSERWS IT'S INCORRECT A very detailed solution and if you can use a program to design after the work please do.Problem : Design a circuit that takes a 3-bit number and increments it by two using a minimum number of 4x1 Mux's and a minimum number of logic gates the output is 4 bits. Show your work and label all inputs/outputs appropriately.
1. Design a sequential circuit with two D flip flops, and two inputs, E and x. If E =0, the circuit remains in the same state regardless of the value of x. When E = 1 and x = 1, the circuit goes through the state transitions from 00 to 01 to 10 back to 00, and repeats. When E =1 and x = 0, the circuit goes through the state transitions from 00 to 10 to 01 back to 00, and repeats. The circuit is to be designed by treating the unused state(s) as don't care condition(s).