(ii) The block on the left incline is 6kg. Find the mass of the block on the right incline so that the system is in equilibrium (no acceleration). All surfaces are frictionless. (ii) Determine the tension in the string if the coefficient of static friction is 0.4. 6 kg 60° m = ? 25° balsts zi qor A od l.gd of 30

(ii) The block on the left incline is 6kg. Find the mass of the block on the right incline so that the system is in equilibrium (no acceleration). All surfaces are frictionless. (ii) Determine the tension in the string if the coefficient of static friction is 0.4. 6 kg 60° m = ? 25° balsts zi qor A od l.gd of 30

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.49P

See similar textbooks

Similar questions

The block of weight W is pulled by the force P inclined at the angle to the horizontal. Find the smallest force P and the corresponding angle that would cause impending sliding of the block. The angle of static friction between the block and the ground is s.
The 40-lb spool is suspended from the hanger GA and rests against a vertical wall. The center of gravity of the spool is at G and the weight of the hanger is negligible. The wire wound around the hub of the spool is extracted by pulling its end with the force P. If the coefficient of static friction between the spool and the wall is 0.25, determine the smallest P that will extract the wire.
Find the largest value of b/h at which the folding table is in equilibrium. The coefficients of static friction are 0.5 at A and 0.3 at C. Neglect the weight of the table.
The coeffient of static friction between the uniform bar AB of weight W and the ground is 0.45. Find the smallest angle and the corresponding force P that would initiate simultaneous tipping and sliding of the bar.
The single-threaded screw of the floor jack has a pitch of 0.5 in. and a mean radius of 1.75 in. The angle of static friction is 8.5. (a) Determine the couple C that must be applied to the screw to start lifting a weight of 4000 lb. (b) What is the couple required to start lowering the weight?
The 600-lb cable spool is placed on a frictionless spindle that has been driven into the ground. If the force required to start the spool rotating is F = 160 lb, determine the coefficient of friction between the ground and the spool. Neglect the diameter of the spindle compared to the diameter of the spool.
The brake pads at C and D are pressed against the cylinder by the spring BF. The coefficient of static friction between each pad and the cylinder is 0.15. Find the smallest tension in the spring that would prevent the cylinder from rotating when the clockwise couple M=2200lbin. is applied. Neglect the weights of the members.
Two identical chairs, each weighing 14 lb, are stacked as shown. The center of gravity of each chair is denoted by G. The coefficient of static friction is 0.2 at B (the contact point between the chairs) and 0.35 at A, C, and D. Determine the smallest force P that would cause sliding.
If the input force to the compound lever is P = 30 lb, calculate the output force Q.
the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is 35 kN . The coefficient of friction between A and surface is 0.2 and between two block A and B is 0.15. Answer :the following P=40KN The coefficient of friction between * block B and surface is 0.24 O 0.63 0.56 O 0.37
the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is 35 kN . The coefficient of friction between A and surface is 0.2 and between two block A and B is 0.15. Answer :the following P=40KN Lë 5 The value of friction force between two * blocks is 5.6 kN 6.4 kN 4.8 kN Non above-mentioned
the system blocks shown below is in equilibrium, the weight of block A is 10 kN and for block B is 35 kN . The coefficient of friction between A and surface is 0.2 and between two block A and B is 0.15. Answer :the following P=40KN The value of friction force between * block A and its surface is 4.0 kN 5.5 kN 6.2 kN O Non above-mentioned