I need help specifically with step 3. In step 3 it says use that formula to find the concentration. Attached I have a table that shows what each beaker has. Can you help me calculate the concentration for all five beakers? ExperimentCu²+lons1: Measure Absorbance versus Concentration forRecord your data in Table 44.11. Take five clean 50 mL volumetric flasks from the Containersshelf and place them on the workbench.1. Fill the flasks with the following amounts of 0.060 Mcopper(II) sulfate and 1 M nitric acid found in Table 44.1.2. Obtain 5 cuvettes from the Containers shelf. Transfer 3 mLfrom the first flask into the first cuvette, from the second flaskinto the second cuvette, and so on until all five cuvettes arefilled.3. Use the dilution formula, M₁ V₁ = M₂V/₂, to calculate theconcentration of Cu²+ ions in all 5 cuvettes. Record theseconcentrations. Note: there is 1 mole of Cu²+ in 1 mole ofCuSO4 so [Cu²+] =[CuSO4].4. Obtain another cuvette from the Containers shelf and place iton the workbench. Add 3 mL water. This is the blank cuvette.5. Take a Spectrophotometer and place it on the workbench.Place the blank cuvette into the spectrophotometer. Check tomake sure the spectrophotometer output is still absorbance(A). Set the wavelength to 700 nm. This is the Amax for copperions. Press the Zero button.6. Table 44.1 Flask volumes and concentration.Volume of 0.06 MCuSO4 (mL)Volume of 1 MHNO3 (ML)Flask 1Flask 2Flask 3Flask 4Flask 5102030405040302010Total Volume (mL) Concentration ofCu²+ (M)5050505050abs: 0.103trans: 78.8abs: 0.207trans:62.1abs: 0.310trans: 48.9abs: 0.414trans: 48.6abs: 0.517trans: 30.4

Note the following in the given dilution formula and solve for M2. M1V1 =M2V2M1 = Concentration of…

Answered: In step 3 it says use that formula to…

In step 3 it says use that formula to find the concentration. Attached I have a table that shows what each beaker has. Can you help me calculate the concentration for all five beakers?

Appl Of Ms Excel In Analytical Chemistry

2nd Edition

ISBN:9781285686691

Author:Crouch

Publisher:Crouch

Chapter4: Least-squares And Calibration Methods

Section: Chapter Questions

Problem 9P

See similar textbooks

Similar questions

Give the advantages and disadvantages of sequential injection analyzers compared to traditional flow Injection analyzers.
Based on the data, calculate the concentration of analyte in the ORIGINAL sample in ppm. Report to 1 decimal place Sample: A 10.00 mL aliquot of the unknown was placed in a 100.0 mL volumetric flask and made up to the mark will distilled water. The absorbance of this solution is 0.185. Sample + Spike: A 10.00 mL aliquot of the unknown and a 13.00 mL aliquot of the 46.00 ppm stock were both placed in the same 100.0 mL volumetric flask and diluted to the mark with water. The absorbance of this solution is 0.326. ( Please type answer note write by hend)
Tube #: 2 3 4 mL 0.0120 M Pb(NO,), 5.00 5.00 5.00 5.00 2.00 3.00 4.00 5.00 mL 0.0300 M KI mL 0.20 M KNO, 3.00 2.00 1.00 0.00 Total vol. (mL) 10.00 10.00 10.00 10.00 Absorbance of soln. 0.381 0.420 0.470 0.542 [I] at equilibrium (M)
M (2022-23) Unit 1: Mole Concept, Unit 4 (FR) (Version 2) Assessment: Chemical Reactions 0.90 0.80- 0.70- 3 0.60 0.50- 0.40- 0.30- Absorbance 2. To spectrophotometrically determine the mass percent of cobalt in an ore containing cobalt and some inert materials, solutions with known [Co²+] are prepared and the absorbance of each of the solutions is measured at the wavelength of optimum absorbance. The data are used to create a calibration plot, shown below. 0.20 0.10- 0.00+ ㅏ 0.005 0.010 34 0.015 Concentration (M) .04 co₂ 100- pertoc A 0.630 g sample of the ore is completely dissolved in concentrated HNO3(aq). The mixture is diluted with water to a final volume of 50.00 mL. Assume that all the cobalt in the ore sample is converted to Co²+ (aq). (a) What is the [Co²+] in the solution if the absorbance of a sample of the solution is 0.74 ? (b) Calculate the number of moles of Co²+ (aq) in the 50.00 mL solution. (c) Calculate the mass percent of Co in the 0.630 g sample of the ore. Answer…
0.200 M 0.00200 M Test Tube No. [FESCN2*1std (M) Absorbance Fe(NO3)3 (mL) KSCN (mL) 17.98 1.97 0.815 5 (Standard) Edit Edit Edit NG 1 Info
The absorbance values at 250nm of 5 standard solutions, and sample solution of a drug are given below: Conc. (ug/ml) A 250 nm10 0.16820. 0.32930 0.50840. 0.66050 0.846Sample. 0.661Calculate the concentration of the sample
3. 4. Experiment 4 Page 2 CHEM 125L The standard solutions are prepared according to Table 1. Final volume is 25.0 ml for each standard. The solvent is 0.1 M nitric acid. Do not use water to bring the volume to 25.0 mL. Plot the data of [FESCN2+] vs. Absorbance. Find the equation of the line. You will need this for Part B. Table 1 Vol. of 0.20 M Fe(NOs)s (mL) Standard Solution Absorbance at 447 Vol. of 0.001 M NaSCN (mL) [FESCN2*] Blank 10.0 10.0 0.076 1.0 1. 10.0 2.0 0-172 2. 10.0 3.0 0.340 10.0 10.0 5.
Table 1.0 of data showing calibration standards prepared by dilution and the absorbance Concentration CuSO4 (M) Volume of 0.5M (ml) Volume of D/Water (ml) Absorbance 0.00 0.10 0.20 0.30 0.40 0.50 II. 0.00 1.00 2.00 3.00 4.00 5.00 5.00 4.00 3.00 2.00 1.00 0.00 1. Construct a graph of concentration against absorbance, clearly show a best fit line. Find regression of your graph. Show how 0.000 0.406 0.638 0.854 1.202 1.276
3. The lead in a swab sample, lead standards, together with a blank were made up in 5.00 mL volumetric flasks using 0.2 % HNO3. 20 μL aliquots of these solutions were injected into the spectrophotometer and the absorbance measured at 217 nm. The following results were obtained. lead / ppb Absorbance 0 0.0591 10.00 0.0858 50.00 0.1926 100.0 0.3260 150.0 0.4594 200.0 0.5929 Swab sample 0.3700 (a) Determine the amount of lead in the swab sample in μg.
100 MASS SPECTRUM 80 60 40 20 0.0 10 20 30 40 50 60 m/z NIST Chemistry WebBook (https://webbook.nist.gov/chemistry) 1. What is the M'? 2. What is the m/z of the base peak? 3. Does it contain chlorine? Explain your answer. Rel. Intensity
> > A UVMisible spectrophotometer was zeroed with distilled water at 510 nm, using a 1.5 cm quertravel The absorbances of four standard Co() solutions were then measured at the sam table below indicates the data. Calculate the moler absorptivity (e) by considering ALL the date points in your calculation 0 OLD [Co] mol dim 0 1.06-03 2.06-03 4.0E-03 8.06-03 Absorbansie / Absorbance 0.00 020 097 26 H DO D OFW0 L Peal 1 ORD
50 Percentage Red No. 40 Soln 100% 80% 60% 40% Table 4.1: Dilutions of Red No. 40 & Absorbance Volume of Red No. 40 Soln (mL) 10me 8mL опи 4mL Percentage Red No. 40 Soln 100% 80% 60% 40% 20% Volume of DI Water (mL) OML 2mL LIML M UML 8ML Table 4.2: Dilutions of Red No. 40 & Absorbance Concentration Red No. 40 2. Report the wavelength with the maximum absorbance of Red No. 40 dye. Absorbance 20% 2ML Part A: Making a Calibration Curve for Beer's Law 1. Calculate the concentrations of each of your diluted Red No. 40 solutions and add these to Table 4.2. Show at least one sample calculation in the space below. 0.251 0.192 Total Volume 0.181 0·119 0.060 (mL) 10 mL 10 mL 10 mL 10 mL 10 mL