Wheatstone Bridge Experiment:In the circuit shown if the wire AB has a length ofone meter, the galvanometer G reads zero at pointC. along the wire, the value of unknown resistorRx (ohm) is:2020a) 6b) 4c) 1.5d) 2e) None.AHa3 voltسالRx-60 cmmmmmRs=90B

Given value--- the galvanometer G read zero at point C. RS = 9 ohm. We have to find--- Rx ?

In the circuit shown if the wire AB has a length of one meter, the galvanometer G reads zero at poin C. along the wire, the value of unknown resistor Rx (ohm) is: HE 2020 a) 6 b) 4 c) 1.5 d) 2 e) None. A 3 volt til+ mm Rx 60 cm Inn Rs 90 B

In the circuit shown if the wire AB has a length of one meter, the galvanometer G reads zero at poin C. along the wire, the value of unknown resistor Rx (ohm) is: HE 2020 a) 6 b) 4 c) 1.5 d) 2 e) None. A 3 volt til+ mm Rx 60 cm Inn Rs 90 B

College Physics

10th Edition

ISBN:9781285737027

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter17: Current And Resistance

Section: Chapter Questions

Problem 66AP: When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T ...

See similar textbooks

Similar questions

In Figure 21.41. does the graph indicate the time constant is shorter for discharging than for charging? Would you expect ionized gas to have low resistance? How would you adjust R to get a longer time between flashes? Would adjusting R affect the discharge time?
Currents of approximately 0.06 A can be potentially fatal. Currents in that range can make the heart fibrillate (beat in an uncontrolled manner). The resistance of a dry human body can be approximately 100 k . (a) What voltage can cause 0.06 A through a dry human body? (b) When a human body is wet, the resistance can fall to 100 . What voltage can cause harm to a wet body?
Integrated Concepts A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. (a) What is the battery’s internal resistance? (b) What power is dissipated inside the battery? (c) At what rate (in °C/min ) will its temperature increase if its mass is 20.0 kg and it has a specific heat of 0.300 kcal/kg. °C, assuming no heat escapes?
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
A 20.00-V battery is used to supply current to a 10-k resistor. Assume the voltage drop across any wires used for connections is negligible, (a) What is the current through the resistor? (b) What is the power dissipated by the resistor? (c) What is the power input from the battery; assuming all the electrical power is dissipated by the resistor? (d) What happens to the energy dissipated by the resistor?
Residential building codes typically require the use of 12-gauge copper wire (diameter 0.205 cm) for wiring receptacles. Such circuits carry currents as large as 20.0 A. If a wire of smaller diameter (with a higher gauge number) carried that much current, the wire could rise to a high temperature and cause a fire. (a) Calculate the rate at which internal energy is produced in 1.00 m of 12-gauge copper wire carrying 20.0 A. (b) Repeat the calculation for a 12-gauge aluminum wire. (c) Explain whether a 12-gauge aluminum wire would be as safe as a copper wire.
A homemade capacitor is constructed of 2 sheets of aluminum foil with an area of 2.00 square meters, separated by paper, 0.05 mm thick, of the same area and a dielectric constant of 3.7. The homemade capacitor is connected in series with a 100,00- resistor, a switch, and a 6.00-V voltage source, (a) What is the RC time constant of the circuit? (b) What is the initial current through the circuit, when the switch is closed? (c) How long does it take the current to reach one third of its initial value?
Three identical 60.0-W, 120-V lightbulbs are connected across a 120-V power source as shown in Figure P28.72. Assuming the resistance of each lightbulb is constant (even though in reality the resistance might increase markedly with current), find (a) the total power supplied by the power source and (b) the potential difference across each lightbulb.
When a straight wire is heated, its resistance changes according to the equation R = R0 [1 + (T T0)] (Eq. 17.7), where is the temperature coefficient of resistivity. (a) Show that a more precise result, which includes the length and area of a wire change when it is heated, is R=R0[1+(TT0)][1+(TT0)][1+2(TT0)] where is the coefficient of linear expansion. (See Topic 10.) (b) Compare the two results for a 2.00-m-long copper wire of radius 0.100 mm, starting at 20.0C and heated to 100.0C.
(Indicates a review question, which means it requires only a basic understanding of the material to answer. Questions without this designation typically require integrating or extending the concepts presented thus far.) . Six resistors, all having the same temperatures and compositions, are each attached to a battery with voltage V to form a simple circuit. The resistors have different lengths, l, but the same diameters. Rank the circuits according to the current that flows through the resistor from smallest to greatest. If two (or more) circuits have the same current flowing, give them the same ranking. Explain the rationale you used to establish your rankings. Circuit 1: l = 2 cm; V = 3 V Circuit 2: l = 2 cm; V = 6 V Circuit 3: l = 1 cm; V = 3 V Circuit 4: l = 1 cm; V = 6 V Circuit 5: l = 3cm; V = 2 V Circuit 6: l = 3cm; V = 6 V
mam/sir how do u draw an electrical circuit, with a voltometer and a anmeter.
Iks) The circuit shown: 9.00 V battery and a 3.50 W light bulb. a) Find the internal resistance of the battery, r, if the electric current that leaves the battery is 0.400 A. P= 3.50 W :-E = 9,00 Vi I =0.400 A b) The light bulb is now replaced by a lower resistance light bulb. The terminal voltage will now be (Explain) : less than before, the same as before, greater than before.