In the Gram Stain, safranin is the dye used to stain gram negative bacteria. This solution is 0.5%wtivoln safranin. How many milligrams of safranin are in a 120 mL safranin solution? Report your answer to two decimal places. Perform all calculations in a single step using Excel to avoid accruing rounding error.

In the Gram Stain, safranin is the dye used to stain gram negative bacteria. This solution is 0.5%wtivoln safranin. How many milligrams of safranin are in a 120 mL safranin solution? Report your answer to two decimal places. Perform all calculations in a single step using Excel to avoid accruing rounding error.

Principles of Modern Chemistry

8th Edition

ISBN:9781305079113

Author:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Publisher:David W. Oxtoby, H. Pat Gillis, Laurie J. Butler

Chapter11: Solutions

Section: Chapter Questions

Problem 10P

See similar textbooks

Similar questions

What is the difference between (a) mass and density? (b) an extensive and an intensive property? (c) a solvent and a solution?
I need help calculating the moles of acid and basebised and also the molarity of the base solution oles RECORD ALL DATA IN INK using the correct number of significant figures and correct units. SHOW COMPLETE "SET-UPS" (and the rounding off) for all calculations for Part 3 on the bottom of this page or on a separate sheet. 3. Standardization of the NaOH Solution: Titration No. Acid buret, Final reading Initial reading Volume of acid used Moles of acid used Base buret, Final reading Initial reading Volume of base used Moles of base used Molarity of base solution Set-ups: 1 2 3 24ml 36. 24ml 12- 12 m 12ml Average Molarity of the NaOH solution Average Deviation 13 25.5 13 13 12.5ml 12 mil. 31.5 4 5 6
A chemist mixes 34.9 g of diethyl ether with 52.1 g of 2-ethyltoluene and 9.03 g of butanoic acid. Calculate the percent by mass of each component of this solution. Be sure each of your answer entries has the correct number of significant digits. component mass percent diethyl ether 2-ethyltoluene 0% 0% butanoic acid
When performing the gram stain, the Crystal Violet solution is composed of 20 mL of 95% ethanol in a final volume of 100 mL. If only 70% ethanol is available, how many mL of ethanol should be added to achieve a final volume of 1,000? Report your answer to 2 decimal places. Perform all calculations in a single step using Excel to avoid accumulated rounding error.
$ F4 An aqueous solution of 2.87 M hydrochloric acid, HCl, has a density of 1.05 g/mL. The percent by mass of HCl in the solution is %. Submit Answer % 5 T G F5 Retry Entire Group 9 more group attempts remaining 6 Cengage Learning | Cengage Technical Support Y H [Review Topics] [References] Use the References to access important values if needed for this question. MacBook Air F6 & 7 gilinent-take F7 8 00 1 DII FB K ( 9 F9 0 L ) O A F10 P Chapter Previous + 11 X Next ☐ Save and Exit OWLY S deles
A student prepares a 1.1 mM aqueous solution of 4-chlorobutanoic acid (C3H6CICO₂H). Calculate the fraction of 4-chlorobutanoic acid that is in the dissociated form in his solution. Express your answer as a percentage. You will probably find some useful data in the ALEKS Data resource. Round your answer to 2 significant digits. % x10
Imagine you collected a master batch (undiluted) wastewater sample as shown in the illustration below. The total mass of lead (Pb) found in 300 mL of a two-fold diluted master sample was 1.65 µg Calculate the amount of Pb in the master batch sample of the wastewater in ppb. Enter numerical values rounded to one significant figure without units. O Volume of solution: 1 L Mass of solution: 1.1 kg
An aqueous sodium nitrate (NANO3) solution must be created for an experiment. If 50.00 mL of a 0.150 M solution is needed, what amount of sodium nitrate (in grams) must be weighed out? Only input numbers. Your answers must be expressed to the thousandths place. Any values less than one must have a zero in front of the decimal (e.g. 0.01 not .01).
Complete the table by entering the molarity of B2- for each standard solution. Show an illustrative calculation for tube ‘A’. Use the dilution formula and express each result to one more digit than allowed by applying the rules of significant figures. Standard Volume of stock B2- solution taken, mL Molarity of dilute B2 Construct a graph of Absorbance vs. molarity of B2- in Excel using the data in the preceding table. Make certain to title the graph and include axes labels with proper units. Absorbance is dimensionless (has no unit). Add a linear trendline to the graph but do not set the y-intercept to zero Solid M2B is added to 25 mL of water, the resulting mixture is continually stirred for 1 hour. At this point, it is assumed that equilibrium (eqn 3) has been established. The mixture is transferred to a test tube, and the test tube is centrifuged to assure that any residual solid M2B is fully settled out. A portion of the supernatant in the test tube is carefully…
An aqueous sucrose (C12H22O11) solution must be created for an experiment. If 100.00 mL of 0.200 M solution is needed, what amount of sucrose (in grams) must be weighed out? Only input numbers. Your answers must be expressed to the hundredth place. Any values less than one must have a zero in front of the decimal (e.g. 0.01 not .01).
A student prepares a a1.0mM aqueous solution of 4-chlorobutanoic acid C3H6ClCO2H. Calculate the fraction of 4-chlorobutanoic acid that is in the dissociated form in his solution. Express your answer as a percentage. You will probably find some useful data in the ALEKS Data resource. Round your answer to 2 significant digits.
Four standard sucrose solutions (10 mL each) are made by adding the masses in the table. Determine the concentration in molarity. (Use sucrose FW: 342.3 g/mol) Sucrose Concentration (M) mass (g) 0.503 0.984 1.443 1.922 The significant figures of the volume (10 mL) has been intentionally left ambiguous. What experimental / procedural choice will determine the number significant figures?