In the power system below, where would you expect to see a step-down transformer?0 0 0 0I.APower Plant12III. CGenerationII. A and BIV. B and CAStationHigh-Voltage Power LinesTransmissionBSubstationCDistribution Power LinesIndustrial ConsumerCommercial ConsumerResidential ConsumerDistribution

In power system transformers changes the voltage levels , so that transmission losses is reduced .…

In the power system below, where would you expect to see a step-down transformer? Power Plant Generation I.A II.A and B III. C IV. B and C A Station High-Voltage Power Lines Ly Transmission B Substation C Distribution Power Lines ( .0000 Industrial Consumer Commercial Consumer Residential Consumer Distribution

In the power system below, where would you expect to see a step-down transformer? Power Plant Generation I.A II.A and B III. C IV. B and C A Station High-Voltage Power Lines Ly Transmission B Substation C Distribution Power Lines ( .0000 Industrial Consumer Commercial Consumer Residential Consumer Distribution

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.26P: A bank of three single-phase transformers, each rated 30MVA,38.1/3.81kV, are connected in Y- with a...

See similar textbooks

Similar questions

A bank of three single-phase transformers, each rated 30MVA,38.1/3.81kV, are connected in Y- with a balanced load of three 1, Y-connected resistors. Choosing a base of 90MVA,66kV for the high-voltage side of the three-phase transformer. spify the base for the low-voltage side. Compute the per-unit resistance of the load on the base for the low-voltage side. Also, determine the load resistance in ohms referred to the high-voltage side and the per-unit value on the chosen base.
In order to avoid difficulties with third-harmonic exciting current, which three-phase transformer connection is seldom used for step-up transformers between a generator and a transmission line in power systems. (a) Y- (b) -Y (c) Y-Y
Three single-phase two-winding transformers, each rated 25MVA,54.2/5.42kV, are connected to form a three-phase Y- bank with a balanced Y-connected resistive load of 0.6 per phase on the low-voltage side. By choosing a base of 75 MVA (three phase) and 94 kV (line-to-line) for the high-voltage side of the transformer bank, specify the base quantities for the low-voltage side. Determine the per-unit resistance of the load on the base for the low-voltage side. Then determine the load resistance RL in ohms referred to the high-voltage side and the per-unit value of this load resistance on the chosen base.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
The p.u. impedance value of an alternator corresponding to base values of 13.2 kV and 30 MVA is 0.2 p.u. Then the p.u. impedance value of an alternator for the new base values of 13.8 kV and 50 MVA is......
Derive physically the reason of the phase shift in three phase transformer and show the phase shift for Dy11 between primary & secondary voltages theoretically using a connection diagram and phasor diagram.
Write the short notes on Reactive Power compensation for test transformer. (Submit Through Turnitin via Moodle)
The line-to-ground voltages on the high voltage side of a step-up transformer are 100 KVZ0° , 33 kVZ-100° and 38 kVZ176.5° on phases a, b and c respectively. Determine the symmetrical components of voltage of phase a and phase b. Draw the negative sequence phasor diagram.
A 10 MVA three phase load is to be served by a three phase transformer at aline voltage of 13.8 kV. The supply side voltage(line-line) is 138 kV. Varioussingle phase transformers are available in the warehouse but all havewindings with voltage ratings under 100 kV and current ratings under 250 A.Is it possible to serve the load using only three single phase transformers? Ifso, specify the three phase connections and the low and high voltage ratingsof the single phase transformers.
A 50 Hz, Scott connected transformer supplies an unbalanced two phase load at ( 400 V) per phase. For the leading phase the load has a resistance of (13.3 ohm) and capacitor of (318) micro farad in series. For the other phase the load consists of resistance (10) ohm and an inductance of (42.3) mH. Calculate both mathematically and graphically the lines currents on 3- phase side. The main transformer primary to secondary turns ratio is (12/1).
Three zones of a single-phase circuit are identified in Figure. The zones are connected bytransformers T1 and T2, whose ratings are also shown.Using base values of 30 kVA and 240 volts in zone 1:a. draw the per-unit circuit and determine the per-unit impedances and the per-unitsource voltage.b. calculate the load current both in per-unit and in amperes. Transformer windingresistances and shunt admittance branches are neglected.