installing
Q: Explain this diagram for dummy
A: The given circuit is as shown below,
Q: Take a look at the wire supplying your house, another residential house, commercial and industrial…
A: Wires selection is an important decision while designing the electrical connections for the…
Q: . Identify and explain the safety procedures and precautions that should be followed for fire…
A: There is always a danger when installing some form of wire or wiring system. If the wires are not…
Q: The grounded circuit (system) conductor is generally not permitted to be used to ground equipment on…
A: Given, The grounded circuit (system) conductor is generally not permitted to be used to ground…
Q: A bolted line to line short circuit is used to determine the thermal withstand rating of the cables…
A: The power system has to transmit power from the generation side to the load side. For this purpose,…
Q: 8. Where the nameplate of an air-conditioning unit specifies the minimum ampacity required for the…
A:
Q: 4.a. The installation of motor controllers and combination load equipment is not permitted if the…
A: A motor controller is a device or combination of devices, that can control how an electric motor…
Q: Describe what the following conductor designation means when it is printed on the insulation;…
A:
Q: 17. In an air compressor system, the distribution piping can be bonded using the A. equipment…
A: Dear student as per our guidelines we are supposed to solve only one question.kindly repost other…
Q: Explain the diagram
A: The above diagram shows the connection to drive a unipolar stepper motor using ULN2803A Array with a…
Q: When testing the twisted pair cable through cable tester, if the LED lights are jumping back and…
A: Cable Tester- Cable tester is a device which is used to test a cable. Cable tester detects the…
Q: 9. How is equipment containing ungrounded electrical systems required to be marked? A. With green…
A: An ungrounded system is a system that is not grounded intentionally. The neutral wire of an…
Q: homeowner wants to add 12 general-purpose receptacle outlets to the electrical drawings before the…
A: Please refer the attached images for the complete answer..
Q: 11. What are at least two instances where a splice is allowed to be made in underground consumer's…
A: The power system has to transmit power from the generation side to the load side. For this purpose,…
Q: Identify and explain the safety procedures and precautions when working with tools and equipment's…
A: Electrical cables are used for transferring the signals and are also used for long distance…
Q: The frames of ranges, wall-mounted ovens, counter-mounted cooking units, and clothes dryers under…
A: Materials that allow current to flow through them are called conductors. The materials that do not…
Q: 10. Which of the following statements about ground faults is true? A. They usually occur between any…
A: Ground faults: It happens when an energized conductor develops an accidental contact with the…
Q: Refer to the National Electrical Code or the working drawings when necessary. Where applicable,…
A: We are authorized to answer one question at a time, since you have not mentioned question you are…
Q: Which of the following would help avoid the choke effect in grounding electrode conductors? A.…
A: The correct option is B that us using an appropriate PVC(POLY VINY CHLORIDE) CONDUIT WILL AVOID…
Q: 5. How many system bonding jumpers normally are there for a separately derived system that's…
A: We are authorized to answer only 1 question at a time since you have not mentioned which question…
Q: When the nameplate of HVAC equipment is marked “Maximum Size Fuse—50 Amperes,” is it permitted to…
A: The device that have the maximum size are generally air conditioner and the refrigerator have the…
Q: The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension is…
A: True, The equipment grounding conductor of a grounding-type receptacle or a branch-circuit extension…
Q: Which of the following statements about equipment grounding conductors is true? A. Unacceptable…
A: Correct option is B that is ELECTRIC GROUND CONDUCTORS must be capable of withstanding the higher…
Q: Which of the following must be notified prior to equipment shutdown for repair? a. Director of…
A: In this question we will write Which must be notified prior to equipment shutdown for repair..
Q: List the methods by which an equipment grounding conductor is connected to a device box
A:
Q: Two persons are standing near a HV equipment and working on it, when an arc flash occurred. Person A…
A: According to the given information, person A was standing directly in front of the high voltage (HV)…
Q: What type of bonding jumper connects the grounded circuit conductor and the equipment grounding…
A: In a power system , Main bonding jumper connects the grounded circuit conductor and the equipment…
Q: How many conductor volume allowances should be applied for the equipment grounding conductors in the…
A: We need to answer how many conductor volume allowances should be applied for the equipment grounding…
Q: Lockout is required: During servicing and maintenance where unexpected ener- gization or start-up of…
A: Bartleby has policy to solve only first question and if it has subparts then solve only first 3…
Q: Explain how electricty power is generated and tramnsimitted to customer unit. Show The single line…
A: The electrical power is generated and transmitted to the consumer : The electrical power is…
Q: NO. 3 In your own words and from your own understanding, avoid plagiarism or copying from the Course…
A: We have to describe the OIL CIRCUIT BREAKER with proper schematic diagram. First we can discuss…
Q: 21.Which of the following wiring methods may be used inside the duct used for vapor removal and…
A: 21. As per the NEC guidelines, no wiring system should be installed in any duct used for vapor…
Q: Determine the minimum number of cubic inches required for two 10 AWG conductors passing through a…
A: AWG or American Wire Gauge is the US standard measure for the diameter of electrical conductors. The…
Q: Provided the bus-bar arrangement below, provide the following: a. Name the bus-bar arrangement; b.…
A: An electrical bus bar is a conductor or a group of conductor used for collecting electric power…
Q: A ____shall be used to connect the equipment grounding conductors, the service equipment enclosures,…
A: Given, 3 multiple choice questions related to national electrical code.(NEC). Please find the below…
Q: In the conduit diagram shown in attached picture, determine how many wires are in each conduit…
A: The circuit is shown below: Between the three-phase line and the disconnect switch. The switch is…
Q: of p o How many conductors enter the ceiling fan/light wall box? Switch ond out let boxes s tirst…
A: We are authorized to answer one question at a time since you have not mentioned which question you…
Q: List the equipment in detail with rating for substation and swictchgear installation.
A: It is asked to list out the equipment required for substation and switchgear installation with the…
Q: When installing a surge arrester at the service of less than 1000 volts, the grounding conductor…
A: Equipment Grounding Conductor (EGC) – A conductive path that 's a component of a decent ground-fault…
Q: 3. How is the insulation arrangement done for different parts in switchgear?
A: Different types of insulation are used in the constructions of switchgear.
Q: All answers should be written in complete sentences. Calculations should be shown in detail, and…
A: Givensupply voltage=230 vname plate full lod current=185 Apower=75 hppower factor=80%
Q: 11.a. Which of the following is a point where a grounding electrode conductor connection must be…
A: Answer 11 (a) : According to national electrical code 250-(96), Grounding electrode conductor…
Q: A? Conductor is defined in NEC 240.2 as a conductor, other than a service conductor, having…
A: The article 240.2 determine the current limiting of the over current protective device is used to…
Q: A line has a rated current of 1,000 A. Assume that a relay (with a rated current of 5A) is connected…
A: In this question we need to find secondary pickup current in per unit .
Q: The copper line with a total length of 20 meters operates in the 220 volt city network. If three…
A:
Q: 18. How many electric meters are provided for this residence?
A: As per the bartleby rule you can ask only one question at a time so please ask other question…
Q: What size equipment grounding conductor is used with # 8 AWG nonmetallic-sheathed cable
A: The minimum size equipment grounding conductor is selected on the basis of the current rating…
Q: Please provide Handwritten answer Question: NEC Reference Answer __________ __________ _____ is…
A: Although, Patient equipment grounding point is used ,to the eliminate the electromagnetic…
11.a. You're installing an isolated power system in a hospital that'll serve a group of patient care areas. Which
of the following colors must be used for the wire that connects to the terminal at each receptacle that's
usually reserved for the neutral conductor?
A. Green with a white stripe
B. Orange with a distinct stripe
C. White with an orange stripe
D. Red with a black stripe
11.b. The _______ is typically where the service main bonding jumper is installed or where the system
bonding jumper is installed for a separately derived system.
A. equipotential plane
B. site-isolating device
C. point of grounding
D. isolated power system
Trending now
This is a popular solution!
Step by step
Solved in 3 steps with 1 images
- Equipment Grounding 10. Which of the following statements about ground faults is true?A. They usually occur between any grounded circuit conductor and the equipment grounding conductor. B. They're often normal and typically intentional.C. They can't result from human error.D. They can happen if a conductive tool is dropped in an energized equipment's electrical enclosure.of p o How many conductors enter the ceiling fan/light wall box? Switch ond out let boxes s tirst 10. What type and size of box may be used for the ceiling fan/light wall box?. 11. What type of covers are used with 4 in. square outlet boxes? 12. a. Does the circuit for the Master Bedroom have a grounded circuit conductor? b. Does it have an equipment grounding conductor? c. Explain the difference between a "grounded" conductor and an "equipment grounding" conductor. 13. Approximately how many feet (meters) of 2-wire cable and 3-wire cable are needed to ft complete the circuit supplying the Master Bedroom? Two-wire cable: ft (- m). m). Three-wire cable: 14. If the cable is laid in notches in the corner studs, what protection for the cable must be provided? 15. How high are the receptacles mounted above the finished floor in this bedroom? 16. Approximately how far from the bedroom door is the first receptacle mounted? (See the plans.) 17. What is the distance from the finished floor to…12. Which of the following statements about ground faults is true?A. They can happen if a conductive tool is dropped in an energized equipment's electrical enclosure.B. They usually occur between any grounded circuit conductor and the equipment grounding conductor.C. They can't result from human error.D. They're often normal and typically intentional.
- 11. Which of the following statements about the use of structural steel as an equipment grounding conductor (EGC) in an AC system is correct? A. Structural steel can be used as an EGC when it's bonded at both ends.B. Structural steel isn't allowed for use as an EGC.C. Structural steel must have an EGC bonding jumper every three feet of structure. D. Structural steel can be used as an EGC bonding jumper between panelboards. 12. Which of the following statements about equipment grounding conductors is true? A. They increase voltages above ground potential on conductors and equipment enclosures during normal operation. B. Unacceptable equipment grounding conductors include conduit, tubing, and cable armor. C. They must be capable of withstanding the higher level of ground-fault current to perform their safety function. D. When they're far from their associated circuit conductors, impedance values are kept as low as possible during ground-fault conditions. 13. Imagine that…8.a. A _______ conductor does not carry current during normal operation.A. neutralB. groundingC. phaseD. grounded8.b. "The complete path of an electric current" describes an electric(al)A. fault.B. circuit.C. source.D. component.When connecting a multiwire (3-wire) circuit to a single phase panel, one ungrounded conductor must be connected to the ____ phase and the other ungrounded conductor must be connected to the ____ phase. Select one: a. A, A b. B, B c. A, B d. doesn’t matter
- 5. How many system bonding jumpers normally are there for a separately derived system that's grounded? A. ThreeB. TwoC. One D. Zero 6. How many grounded neutral conductors are in a 208Y/120 volt, 3-phase, 4-wire system? A. ThreeB. TwoC. One D. Four 7. Which of the following are sometimes installed as an emergency system, legally required standby system, or optional standby power system for a building or structure? A. GeneratorsB. Surge protection devices C. Surge arrestersD. Transformers 8. If the system bonding jumper in a DC system is a screw, what color must the screw be? A. WhiteB. RedC. Orange D. Green 9. If overcurrent protection is provided in the transformer of a separately derived system, which of the following statements is correct? A. An equipment grounding conductor must be run with the conductors between the transformer and the building's disconnect. B. There's no need for service equipment or a panelboard in the separate building.C. A ground electrode must…7.B. The size of a grounding electrode conductor for a service or separately derived system is generally basedon the size of the largestA. ungrounded supply conductor.B. equipment grounding conductor.C. grounded electrode.D. bonding jumper.7.C. Which of the following statements about bonding is true?A. The joint or termination must offer opposition in the circuit for effective electrical connections.B. Effective bonding keeps impedance high if a fault should occur.C. The entire electrical safety circuit is only as good as its strongest bonded link.D. Bonding connections must endure high levels of fault current until overcurrent protective devices can operate.- Loads, Service, and Overcurrent Protection 6.a. The general lighting load is based on a _______ per square foot basis.A. kilowattB. number of circuitsC. volt-ampereD. general illumination6.b. What's the primary disadvantage of using copper conductors?A. AvailabilityB. WeightC. CostD. Durability
- 10.A. Which of the following is required in each separate service disconnecting means?A. Grounding electrodeB. Service conductorC. Main bonding jumperD. Equipment grounding conductor10.B. When sizing an equipment bonding jumper on the load side of an overcurrent protective device, thesize of the conductor jumper is based on theA. current rating of the protective device.B. size of the feeder's equipment grounding conductor.C. size of the grounding electrode conductor.D. size of the conductors feeding the protective device.10.C. Grounding clamps are typically suitable for connecting how many conductors?A. OneB. ThreeC. FourD. Two1. _______ is not considered an effective ground-fault current path. a) Ground b) Equipment grounding conductors c) Equipment bonding jumpers d) Grounded conductors 2.Which of the following is not a conductor in the grounding and bonding scheme for an ungrounded system? a) Grounding electrode conductor for grounding equipment enclosures and conductive parts b) Equipment grounding conductor c) Bonding conductors or jumper d) System grounded conductor____ current occurs when the system neutral is grounded improperly downstream from the service equipment. Select one: A. PHASED B. OBJECTIONABLE C. POSITIVE D. NEGATIVE