Instructions: In the RLC circuit shown below, the switch has been in position 1 for along time before moving to position 2 at t = 0. Calculate the following:a) The initial inductor current I, and initial capacitor voltage V,a) The value of a and wob) The form of the response of the circuit (underdamped, critically damped,overdamped)c) The expression for i, (t) for t≥ 075 mA (†12150 Ω10 ΩiL380 mHEST

Answered: Image /qna-images/answer/0a257997-d472-4592-a4f2-dbd254961724.jpg

Answered: Instructions: In the RLC circuit shown…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Write a small essay about transient in RC Circuits then : For the circuit shown below, The switch has been in position a for along time. At t=0 it moves to position b.. Find Vc for t>0
Problen the following: A. The voltage across the capacitor at the t = 0. B. The voltage across the capacitor for t > 0. C. The voltage across the 32K resistor for t > 0. Given RC circuit with a switch that moves from position A to B at time t =0 obtain
Natural Response of RLC Circuita. charge in capacitor at steady state b. di/dt (in A/s) at t=0+(The previous answer which were 0.001 and -31.25 were incorrect. I do not know what were the miscalculations, please do NOT provide those as answers anymore. Thanks)
In the following circuit, which behavior is correct for the interval t>0? However, the capacitor is initially discharged. 1. as R increases, the capacitor charges more slowly. 2.The voltage across the current source is vc(t). 3. The slope of the vc(t) waveform is I/C. 4. vc(t) is eventually limited to a constant voltage. Please give me a detailed explanation and explain the formula.
Assume the capacitor is in steady state before the switching operation and determine: A. Time constant of this circuit for t > 0 B. Initial voltage of capacitor v(0-) C. Final voltage of the capacitor for t >> 0 (same as v(∞)) D.Voltage v(t) across the capacitor as a function of time for t > 0
Consider the circuit shown, the initial current in the inductor is it (0-) = -0.2A. The switch, has been close for a long time prior to t=0. It opens at t=0. Find expressions for it (t) and v(t) for t≥ 0. Sketch i(t) and v(t) versus time. Write down your detailed calculations step by step and use your words to explain your approach. 0.3A t=0 охо + V(t) 10 mH 2 ΚΩ i₁(t)
Circuit analysis In the circuit below, when the switch is in A position for a long time, it is in position B at t = 0. are brought. For t> 0, the time constant is the value of ? and the voltage across the capacitor. Find the function of change with respect to time. Draw the graph.
The switch in the circuit in the figure has been open for a long time before closing at t=0. Determine Vc (0+ ) and iL (0+ ), the values of the capacitor voltage and current across the inductor immediately after the switch is closed. Let vc (infinity) and iL (infinity) denote the values of the voltage across the capacitor and the current across the inductor after a long time that the switch has closed.Determine Vc (infinity) and iL (infinity) Answer: vc(0 +) = 12V, iL(0 +) = 0, vc(infinity) = 4V, and iL(infinity) = 1mA
7) What is the damping ratio of the closed loop system shown in the figure? a) 0 R(s) b) 1 5 (s+1)(s+3) C(s)
The' Transfer Fcn'block can be extracted from 'Commonly Used Blocks' library. If the dumping ratio is between 0 and 1, the system poles are complex conjugates. A step input can be described as a change in the input from zero to a infinite value at time t = 0. If the damping factor is zero, the unit-step response is a Purely sinusoidal. Manual control
In the following circuit, the switch has been in position a for a long time and then moves to position b at t = 0s. Determine the following: a. The value of the current through the inductor for t < 0s. b. The expressions for il (t) and vI(t) for t > 0s. c. The time it takes for the inductor to return to steady state. d. The values of R3 and R4 that are needed for the inductor to return to steady state in 4 s.
The switches in the figure below have been closed (left switch) and open (right switch) for a long time. Att = 0 the switches change as indicated in the figure. a) Find the initial voltage drop across the capacitor.b) Find the initial energy stored by the capacitor. c) Find the time constant of this circuit for t > 0. d)Write the expression for the capacitor voltage v(t) for t ≥ 0.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS