It is required to design a chaindrive to connect 5 kW, 1400 pmn electrie motorto a drilling machine. The speed reduction is3 : 1. The centre distance should he approximately500 mm.() Select a proper roller chain for the drive.(i) Determine the number of chain links.(iii) Specify the correct centre distance betweenthe axes of sprockets.

Given Power of the electric motor = 5 kW N = 1400 rpm Speed reduction = 3:1 To find Proper roller…

It is required to design a chain drive to connect 5 kW, 1400 rpm electrie motor to a drilling machine. The speed reduction is 3: 1. The centre distance should be approximately 500 mm. (i) Select a proper roller chain for the drive. (i) Determine the number of chain links. (iii) Specify the correct centre distance between the axes of sprockets.

It is required to design a chain drive to connect 5 kW, 1400 rpm electrie motor to a drilling machine. The speed reduction is 3: 1. The centre distance should be approximately 500 mm. (i) Select a proper roller chain for the drive. (i) Determine the number of chain links. (iii) Specify the correct centre distance between the axes of sprockets.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q 16- Find the length of a belt necessary to drive a pulley of 80 cm diameter running parallel at a distance of 12 m from the driving pulley of 480 cm diameter ?
A single-strand roller chain drive connects a 50-hp engine to a lawn waste chipper/shredder, as shown below. As the engine operates at 1000 rpm, the shredding teeth should rotate at 250 rpm. The driven sprocket has 60 teeth. Determine the chain speed.
A chain drive is desired to couple a gearmotor with a bucket elevator. The 40 hp. gearmotor will operate at 350 rpm and the elevator drive shaft must operate as close to 60 rpm as possible. Select an appropriate chain size, commercially available sprockets, and number of links for a chain. Also calculate the actual chain speed and the center distance.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys.
A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys. Note: Sketch the belt drive system for both parts and label the given data on it.
Two shafts 30 in. apart, each carrying a four-step pulley, are to be connected by a cross belt. The driving shaft is to turn 180 rpm while the driven shaft is to turn 50, 150, 250, and 600 rpm. The smallest step of the driver is 10 in. in diameter. Find (a) the diameters of all the steps, (b) angle of contact for each pair of pulleys, and (c) belt length.
2. A blower is driven by an electric motor though a belt drive. The motor runs at 750 r.p.m. For this power transmission, a flat belt of 8 mm thickness and 250 mm width is used. The diameter of the motor pulley is 350 mm and that of the blower pulley 1350 mm. The center distance between these pulleys is 1350 mm and an open belt configuration is adopted. The pulleys are made out of cast iron. The frictional coefficient between the belt and pulley is 0.35 and the permissible stress for the belt material can be taken as 2.5 N/mm2 with sufficient factor of safety. The mass of a belt is 2 kg per meter length. Find the maximum power transmitted without belt slipping in any one of the pulleys. [Ans. 35.9 kW]
A1. A flat belt drive for speed reduction has pulley diameters of 200 mm and 380 mm. Themaximum belt tension is not to exceed 620 N and it is required to transmit 1·8 kW at anoutput speed of 360 rev/min. Determine:(a) The input torque. (b) The belt speed. (c) The limiting slack side tension. (d) The initial tension at which the belt should be set.
The width of the belt used if its thickness is 6 mm. Ans. 261 mm 8. A nylon-core flat belt has an elastomer envelop; is 200 mm wide, and transmits 60 KW at a belt speed of 25 m/s. The belt has a mass of 2 kg/m of the belt length. The belt is used in a crossed configuration to connect a 300 mm diameter driving pulley to a 900 mm diameter driven pulley at a shaft spacing of 6 m. A. Calculate the belt length and the angles of wrap. Ans. 13.95 m, 3.34 rad or 191.4° B. Compute the belt tensions based on a coefficient of friction of 0.33. Ans. 1.76 KN, 1.96 KN
A belt conveyor transports 18 tonnes per hr at 20°. Determine the unit weight of belt material in kg/ply-cm width-m to lift the load vertically up sufficient to give 33.5 m horizontal center-to-center pulley distance. 1750-rpm motor, V-belt drive to helical gear speed reducer. Belt speed, 61 m/min. Discharge over tail pulley. No tripper.
The following drive system is used to raise a load at constant velocity. The motor rotational speed is 1000 rpm, and the rotational speed of the drum is 200 rpm. The efficiency of the gear box is 0.85. The efficiency of the drum is 0.95%. The moment of inertia of the motor (input shaft) is 0.5 kg.m², and the moment of inertia of the drum (output shaft) is 0.75 kg.m². Calculate: (1) The total (equivalent) moment of inertia of the drive system referred to the motor shaft. (2) The developed mechanical power on the motor Drum, 0.5 m diameter shaft. 1000 Kg Motor Gearbox
A V-Belt drive is designed so that it has the input sheave on the shaft of an electric motor (normal torque) rated at .55 hp at 1160 rpm full-load speed. The drive is to a bucket elevator that is to be used 12 hours daily at approximately 675 rpm. The center distance is about 19.5 in. Add the detailed steps of your design to your attached worksheet. Hints: 1) In your design choose an appropriate belt section, specify the small pulley diameter, the large pulley diameter and the length of the belt. Determine the Belt length in inches, in two significant figures. Please enter below a numerical value only, no units are needed. Answer: