can you please find the solution for question 6.31 problems. Unless otherwise stated, the pipe stres gInside diameterssystems andal hose underom the homeFluid Flow Ratesind seamlesss steel, alloykel alloys.6.29 Water at 10°C is flowing at 0.075 m'/s. Calculate theweight flow rate and the mass flow rate.6.30 Oil for a hydraulic system (sg 0.90) is flowing at2.35 x 10 m's. Calculate the weight flow rate andmass flow rate.miding piping.S. and metricof ABS, PVC,6.31 A liquid refrigerant (sg 1.08) is flowing at a weightflow rate of 28.3 N/h. Calculate the volume flow rate andthe mass flow rate.6.32 After the refrigerant from Problem 6.31 flashes into avapor, its specific weight is 12.50 N/m'. If the weight flowrate remains at 28.5 N/h, compute the volume flow rate.acludes tablesin US. Cu

First we have calculated the value of density of refrigerant, density of refrigerant is equal to…

Answered: mass flow rate. 6.31 A liquid…

mass flow rate. 6.31 A liquid refrigerant (sg 1.08) is flowing at a weight flow rate of 28 3 N/h. Calculate the volume flow rate and the mass flow rate. 11 dubes into

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As shown in the picture blew, a pump can deliver volume flow rate of of water through a vertical lift of . The inlet to the pump is just below the water surface and the discharge is to the atmosphere through a DN50 schedule 40 steel pipe. The energy loss . (2) Select the correct simplified general energy equation for point 1 and 2
PROBLEM Ħ 22.a. mass at a pressure the temperature of hot water is being 248.09 °F to 212.09 °F using a heat exchanger. = 2at m and flow rate = 1020 kg /min, decreased from oF using Reservvir waten s used as coolant with mass flow rate = 1800 kalmin and kg Imin inlet temperature = 50.09 oF. 2 The minimun allow able ft? surface are a= 270. 17 of heat ex changer all ow able overall heat = 206.05 btul The transfer coefficient of heat exchanger maximem do z7f4 The heat capací ty to be used must he the average value of inlet and out let temperatures. Hind the Number of Transfer units (NTU) using effective nes NTU Method if the heat exch anger being used is heat exchang er (specify which fluid is mixed or unmixed Cross flow
Compute the resulting pressure in kPa after a "real" diffuser in which the energy loss due to sudden enlargement is considered for the flow of water at 25°C from a 36 mm OD x 2.0 mm wall copper tube to an 85 mm OD x 2.5 mm wall copper tube, the pipes are the same elevation. The volume flow rate is 150 L/min and the pressure before the enlargement is 500.062 kPa. NB: OD = Outside Diameter, Wall refers to the pipe’s thickness (t) Hints: Obtain the specific weight of water for the given temperature from Appendix A (Table A.1). Obtain the resistance coefficient (K) for sudden enlargement from Table 10.3B in chapter 10. Instructions: Only express the areas in scientific notation to three decimal places but round off to three decimal places in normal number format where necessary throughout your calculations leading to the final answer and including the final answer for all other computations excluding the area.
fluid flow sulphuric acid with 75% concentation of density 1650 kg/m³ and viscosity 8.6 m N/m². is to be pumped for 0.8 km along a 50mm internal dimeter pipe at the rate of 3 kg/s and the faised vertically 15m by the рит р driven and has If the pump is electrically efficiency an What the power will be required? take (E) as 0.046 m us of 50% what
The density of water is looe ty/m? and the e Plective bwlk modulus (klis 1.06 Gpa. in a 5omLony pipe Carries water at 1.86 nls. that calculate DP in Mpa. AP=pv pelton wheel the velocity of ) In the incident jet relative to the bucket the water jet velocity is is 6.28 m Is, 23.54 m/s and volumetric flov rate f the jet 109 m/s. Tn an ideal itnation (Cy, * and cos© are all eqnal to !) m/s. In an ideak 2it wat ion Hint V= V, -U = V, -wR DV = (V, -U) (1+k coso) mee W = 27N 60 raA /s
The water is pumped from a 40 sch pipe that has 750 ft lenght, 6 in. nominal diameters. Height difference between exit and entry planes is stated as 50 ft. The yield of waterpump, 80% the power of pump motor is 20 horsepowers. Friction losses are stated as 50ft-lbf/lbm. Please calculate the flow rate in pipe line.
Calculate the power supplied to the pump shown if its efficiency is 75%. Water is at 25 degrees Celsius is flowing at the rate of 50.0 m3/h. The suction linf is a standard DN 100 Schedule 40 steel pip, 15m long. The total length of DN 50 Schedule 40 steel pipe in the discharge line is 200m. The elbows are tight, the entrance to the pipe is flush and the globe valve is completely open. Draw the line of total and piezometric heights.
Compute points on the velocity profile from the tube wall to the centerline of a standard hydraulic steel tube, 50 mm OD x 1.5 mm wall, if the volume flow rate of SAE 30 oil (sg = 0.89) at 110°C is 25 L/min. Use increments of 4.0 mm and include the velocity at the centerline.|
Water at room temperature with a mass flow rate of 2 kg / s flows through a system of 2 pipes connected in series. The first piece of pipe is 10 m long 1 in. Sch. 40, the second piece of pipe is 15 m long 2 in. Sch 40 is made of commercial steel tubing. Piping system is horizontal. Calculate the pressure loss across both pipes and the pump power required to flow water through this piping system, ignoring the energy loss of the fitting. CREATE THE KNOWN AND UNKNOWN BY DRAWING THE SHAPE OF THE ORGANIZATION AND WRITE YOUR ASSUMPTIONS IN DETAIL
A piping system is to be installed at place where the pump will transfer the fluid from tank A to tank B. There are two suggested piping designs available to carry the fluid efficiently. Compute and determine which of the available piping arrangement will experience the less pumping powerwith given flow conditions. Discuss the results. Flow conditions are same for both type of designs and given as: Pipe material: stainless steel Volume flow rate: 40 L/sec Assume the working fluid is water at standard atmosphere temperature and both tanks areopen to atmosphere. Pipe inlet is sharp-edged and bends are sharped without vanes. Elevations are as ?? = ?? ? and ?? = ?? ?
Diagram (1) H(m) 40 36 32 28 24 20 16 12 4 200 400 600 800 1000 1200 1400 1600 1800 V(lit/min)
value of reynold number for fluid flow in pipe and flow is laminar?