Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports v If a simply supported beam Iis subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom . v The bending stress in a section can be reduced by using a F. Midspan at the top . v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA O. At the fibres furthest from the NA P. Fastener force

Match the answers in the columns. v Maximum Shear stress of a cross section. A. using an l-section instead of a rectangular section. v Maximum Bending stress of a cross section. B. Tension and bending force. C. 1m form the supports v If a simply supported beam Iis subjected to a distributed load, where are you most likely to find tension bending cracks. D. At Midspan v Ifa simply supported beam is subjected to a distributed load, where are you most likely to find shear cracks. E. Midspan at the bottom . v The bending stress in a section can be reduced by using a F. Midspan at the top . v Shear stress can be increased by the width of a section. G. At the supports. v The shear force in fasteners. H. Reducing the width of a section. v Moment couple on a section. 1. using a rectangular section instead of an l-section J. Shear flow K. Increasing the width of a section. L. Only at the section sides touching the NA M. In between the NA and the top/bottom fibres N. Usually at the NA O. At the fibres furthest from the NA P. Fastener force

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 1 Please choose the correct answer and also write down your solution. (1) The beam is subjected to the shown loading. What is the correct statement regarding the flexural stress at A and B? P P a. Both og and og are tensile stress. 0.5 m 0.5 m 0.5 m b. Both oa and og are compressive stress. Og is tensile stress and og is compressive stress. с. d. OA is compressive stress and og is tensile stress. A В (2) The cantilever beam is subjected to the load P and has cross section as shown. What is the ratio of the magnitudes of the maximum tensile and compressive flexural stresses over the a-a cross section? b. 3/7 a. 7/2 d. 2/10 е. 3/10 h. 10/3 c. 7/3 f. 10/2 i. 1/1 g. 2/7 250 mm 20 mm 60 mm 200 mm 2 m 1 m 15 mm 15 mm
P A B 1m E 1m 2m The simply supported beam shown has a solid rectangular cross section having beam width of 130mm and a height of 200mm. Assuming values of P = 25KN, w = 30 kN/m, and E = 5m, determine: 1) The max tensile bending stress in MPa (enter this value into D2L answer box, in MPa). Exactly where does this occur along the beam? (4 sigs) 2) The max shear stress in MPa. Exactly where does this occur along the beam? ( 4 sigs) Your Answer:
Q4: For the figure below, determine the principal stresses and show them on a sketch of a properly oriented element. Also, find the maximum shear stresses and show them on a sketch of a properly oriented element. (Consider only the in-plane stresses.) -30MPA 90 MPa -34MPA
For the truss shown, calculate the stress in area of each member BD. The cross-sectional member is 1200mm². 4m B 6m U 3m 4m E 3m 100KN 200KN F M FLSNI
1. The assembly is shown is attached to supports at A and D. Section BCD is a solid 2" diameter aluminum [E = 10,000 ksi] rod. Steel [E = 30,000 ksi] tube AB has an outer diameter of 3.50" and a wall thickness of 0.216 in. Determine (a) the stresses is sections AB, BC and CD, and (b) the deflections of joints B and C. [OAB = 3.40 ksi (C), Osc = 5.863 ksi (T) Oc, = 4.959 ksi (C), 8, = 0,0054"– , d. = 0,02975"→] %3D %3D %3D %3D 13 kips 17 kips A C 13 kips 17 kips 4 ft 5 ft 5 ft
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
The rigid beam is supported by the three suspended bars. Bars AD andCF is made of A-36 steel and BE is made of 2014-T6 aluminum alloyeach having a cross-sectional area of 450mm2. Determine the angle oftilt of the rigid beam DEF and the average normal stress in each bar ifthe rigid beam is subjected to the loadings shown. Take ESt = 200 GPa and EAl = 73.1 GPa.
A beam ABC with an overhang from B toC supports a uniform load of 200 lb/ft throughout itslength (see figure). The beam is a channel section withdimensions as shown in the figure. The moment of inertiaabout the z axis (the neutral axis) equals 8.13 in4.(a) Calculate the maximum tensile stress σt andmaximum compressive stress σc due to theuniform load.(b) Find the required span length a that results inthe ratio of larger to smaller compressive stressbeing equal to the ratio of larger to smaller tensilestress for the beam. Assume that the totallength L =a + b = 18 ft remains unchanged.
! Required information Consider the given state of stress. A 16 ksi 10 ksi Determine the normal and shearing stresses after the element shown has been rotated through 15° clockwise, using Mohr's circle. The normal stress Ox'is - |ksi and Oy'is ksi. The shearing stress Tx'y'is ksi.
Determine the maximum tensile and compressive bending stresses developed in the beam shown. The cross-section has the given properties. NA 1-35 x 10mm a. RA = b. RE= c. fb(c) = d. fb(T) = 80 mm 200 mm A 1.5m kN KN 5kN m MPa MPa B 1.5m SkN/m 2m 5KN n 2m 4
3. For the given structure and boundary conditions, what is the allowable load Pallow if the material strengths in shear and tension are T = 200 MPa and o=360 MPa, respectively? The pins carry shear and bars BC and DE carry axial load. Disregard the stress conditions of member ACD, which carries lateral load. All pins are in single-shear and have a diameter of 12mm. Use a factor of safety of 2.0. A ABC = 100mm2 B D C Pallow E ADE = 100mm² 240mm 150mm
Beams AB and BC are connected with a hinge at B. Select the lightest W-shape for each beam if the working stress in bending is 150 MPa. What are the maximum bending stresses in the selected beams? pls write legibly and show complete solution thank you