Before delivering the vehicle to the customer, it is important to check the vehicle for cleanliness. Technician A says that allthe trash from the repair process needs to be removed. Technician B says that we must ensure that all the windows areclean and free of hand prints. Who is correct?Select one:a. Technician Ab. Technician B1xc. Both A and Bd. Neither A nor B

Before delivering the vehicle to the customer,it is important to check the vehicle for cleanliness.…

Answered: O O O Before delivering the trash from…

O O O Before delivering the trash from the n clean and free of h- Select one: O a. Technicia O b. Technician c. Both A an O d. Neither A

Automotive Technology: A Systems Approach (MindTap Course List)

6th Edition

ISBN:9781133612315

Author:Jack Erjavec, Rob Thompson

Publisher:Jack Erjavec, Rob Thompson

Chapter21: Instrumentation And Information Displays

Section: Chapter Questions

Problem 1ASRQ: While discussing what the maintenance reminders base die time for the next service on: Technician A...

See similar textbooks

Similar questions

All of the following should be done post-repair EXCEPT: Select one: a. go back through the vehicle and look for tools. b. ensure that no damage to the vehicle has been sustained during repair. c. look for worn tires and wiper blades. d. check that all fingerprints have been removed. Next pa page O M
Technician A stresses the need to follow the manufacturer's recommendations for preventive maintenance to his customers. Technician B says that the proper PM service intervals depends on the customer's driving habits and typical driving conditions. Who is correct?
Which of the following would NOT be cause for rejection when checking the windshield and other glass? Any window is broken or has sharp or jagged edges. Any window other than the windshield is cracked, starred, scratched, or discolored so as to obstruct the driver’s view. The vehicle is not equipped with approved safety glass or is not equipped with a windshield. The windshield has a 2 inch diameter“star”.
Technician A says vehicle inspection pits allow access to the vehicle's underside without using a hoist or jack. Technician B says that vehicle inspection pits only need to be covered when a vehicle is over the top of them. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B ge Next page quiz/attempt.pftp?attempt-4403533&cmid%-D3426318&page=9#
Two techs are discussing oil coolers. Technician A says that when inspecting oil- to-water type coolers, look for mixing of the fluids: oil in the coolant, and coolant in the oil. Technician B says that when inspecting oil-to-air type coolers, look for oil in the coolant only. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B
While discussing working on hybrid vehicles: Technician A says to make sure that the high- voltage system is shut down and isolated from the vehicle before working near or with any high-voltage component. Technician B says that when working on or near the high-voltage system , even when it is de - powered , always use insulated tools. Who is correct ?
A technician is inspecting a vehicle and finds the upper radiator hose is collapsed, and the cooling system pulled into a vacuum when cold. Technician A states that a leak in the surge tank could be the cause. Technician B states that the radiator cap is most likely defective. Who is correct? Select one: a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B
Lockout locks: Can be used to lock tool boxes, storage sheds, etc. b. Can be used only for lockout purposes. Are provided by the equipment manufacturer. d. a. C. Must be bright orange in color. Authorized employees must be trained: To recognize hazardous energy sources, and to know the type and magnitude of the hazardous energy sources. b. a. To perform the lockout/tagout procedure. C. When an audit shows deficiencies with the procedure. d. All of the above. When authorized employees perform a shutdown they must: a. Notify all affected employees that they are starting a lockout procedure, b. Locate all energy sources that power the equipment. Follow the procedures to shut down each machine. d. All of the above. с. If several people are needed to work on a piece of equipment: a. The first worker to arrive to the job is the one who applies the locks. b. Their supervisor is the only one who needs to apply a lock. c. Each worker must apply his or her own lock. d. The person who will be the…
The CV joint boots on the left side of a vehicle appear to be squeezed together; the boots on the right side of the vehicle appear to be stretched apart. Technician A says that one or more of the engine/transaxle's mounts may be broken. Technician B says that one or more of the engine/transaxle's subframe mounts may be broken. Who is correct? O a. A only O b.B only C. Both A and B O d. Neither A nor B
Which of the following is not a true of group lockout or tagout? a. Each employee working on the equipment is an authorized employee b. A supervisor may attach a lock for an entire work crew. c. Each person working on the equipment must have a lock or tag d. A supervisor should be the first or last person to attach a lock or tag
Technician A says that if the oil pressure shows low on the vehicle's gauge, engine oil pressure should be verified using a manual test gauge. Technician B says that if a vehicle's oil pressure gauge reads too high, engine oil pressure should be verified using a manual test gauge. Who is correct? Select one: a. Technician A b. Technician B c. Both A and B d. Neither A nor B
Why is it important to know the conditions for running and setting DTC's when carrying out vehicle diagnosis and repair? Give examples. (70 - 100 Words)