If a 4-cylinder, 4-stroke-cycle internal-combustion engine has 1000 rpm and 108 psi mean effective pressure. The piston diameter and stroke is 4” and 5”.Calculate: Piston displacement Total piston displacement Clearance volume of a cylinder if the compression ratio is 16:1 Indicated horsepower Brake horsepower if the mechanical efficiency is 82%.

Given: D=4" L=5" no of cylinder=4 N=1000 P=108 psi To determine: Piston displacement Total…

Answered: Piston displacement Total piston…

Piston displacement Total piston displacement Clearance volume of a cylinder if the compression ratio is 16:1 Indicated horsepower

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. A 4.0 L six-cylinder engine is operating at 3000 rpm. The engine has a compression ratio of 10:1, and volumetric efficiency of 0.85. If the bore and stroke are equal, what is the stroke, the mean piston speed, cylinder clearance volume, and air mass flow rate into the engine? Assume standard inlet conditions (Patm=101kPa and T=25°C)
5. A 5.6 liter V10 compression-ignition truck engine operates on a four stroke cycle at 3600 rpm producing 162 kW of power in the shaft. The bore and stroke of the engine are related as S = 1.12 B. Calculate: (15 pts) a. Average piston speed (m/s) b. Torque (N-m) c. Brake mean effective pressure
8. What will be the total piston displacement in a two-cylinder 100 mm x 130 mm engine? 9. If each cylinder of the above engine has a clearance volume equal to one fifth of the total cylinder volume, then compute: a) the clearance volume; b) the compression ratio. 10. Sketch the operation of a four-stroke petrol engine, explaining the events at each stage. How will the events differ from those of a diesel engine?
In a 4 stroke single cylinder engine clearance volume (Vc) is 30 cm3 and displacement volume (Vd) is 290 cm3. The piston bore is 60 mm. Intake valve is opened at an angle of 25 ᵒ CA before Top Dead Center (TDC) and is closed at an angle of 20 ᵒ CA after the Bottom Dead Center (BDC). Calculate effective compression ratio.
3. An 8-cylinder, 450 mm x 600 mm, 4 stroke cycle diesel engine has an exhaust gas mass rate of 4.5 kg/kw-hr brake based on fuel having air-fuel ratio of 20 to 1 and heating value of 10,540 kcal/kg. Engine speed is 260 rpm with brake mean effective pressure of 9.25 kg/cm2 An estimated 22% energy loss is carried away by the jacket cooling water. Calculate the brake horsepower. B. 2011 BHP C. 2310 BHP D.2910 BHP
+. Page view 360° Exhaust 540° Intake 720° Compression 4. Why do multi-cylinder engines have smaller flywheels than single-cylinder engines? 5. What systems are commonly seen on an engine? What additional systems are needed to use an engine as a tractor? 6. Why does a cam shaft run at half the speed of the crankshaft? Illustrate. 7. How do you designate the size of an engine? 8. What will be the total piston displacement in a two-cylinder 100 mm x 130 mm engine? 9. If each cylinder of the above engine has a clearance volume equal to one fifth of the total cylinder volume, then compute: a) the clearance volume; b) the compression ratio. 10. Sketch the. operation of a four-stroke petrol engine, explaining the events at each stage. How will the events differ from those of a diesel engine? 11. Why is there a power stroke for every down stroke of piston'travel in a two-stroke engine? At what interval does the power stroke occur in a four-stroke engine? 12. Assuming a firing order of 1 3.- 4…
A construction vehicle has a diesel engine with 8 cylinders of 5.375in bore and 8in stroke, operating at four stroke cycle. It delivers 152-shaft horsepower at 1000rpm with a mechanical efficiency of 0.60. Calculate: (Show your complete solution) Total engine displacement (in3) Break mean effective pressure (psia) Torque at1000rpm (lbf-ft) Indicated horsepower Friction horsepower
2. Design a cast iron trunk type piston for a single acting four stroke engine developing 75 kW per cylinder when running at 600 r.p.m. The other avialable data is as follows: Maximum gas pressure = 4.8 N/mm2; Indicated mean effective pressure = 0.65 N/mm?; Mechanical efficiency = 95%; Radius of crank = 110 mm; Fuel consumption = 0.3 kg/BP/hr; Calorific value of fuel (higher) = 44 x 10°KJ/kg; Difference of temperatures at the centre and edges of the piston head = 200°C; Allowable stress for the material of the piston = 33.5 MPa; Allowable stress for the material of the piston rings and gudgeon pin = 80 MPa; Allowable bearing pressure on the piston barrel = 0.4 N/mm2 and allowable bearing pressure on the gudgeon pin = 17 N/mm2.
03/ A 4 cylinder has a following data Bore-15 cm; Piston speed 510 m/min; B.P= 60 kW; T0.80; Pa-5 bar; C.V=40000KJ/kg. Calculate i) whether this is 2 Stroke or 4 Stroke engine and why? 04/ Write a notes on heat balance sheet, draw that on the energy flow and enhance your answers with equations.
Compute the horsepower output of the following described engine operating at 2000 rpm, bore 3.5 in., stroke 4.0 in., 6 cylinders, and 140 psi bmep. 81.634 hp 29.70 hp 103.94 hp 40.817 hp Other:
7. How do you designate the size of an engine? 8. What will be the total piston displacement in a two-cylinder 100 mm x 130 mm engine? 9. If each cylinder of the above engine has a clearance volume equal to one fifth of the total cylinder volume, then compute: a) the clearance volume; b) the compression ratio. 10. Sketch the operation of a four-stroke petrol engine, explaining the events at each stage. How will the events differ from those of a diesel engine? 11. Why is there a power stroke for every down stroke of piston travel in a two-stroke engine? At what interval does the power stroke occur in a four-stroke engine? 12. Assuming a firing order of I four-cylinder engine, complete the events in the other cylinders if the events for cylinder l'are as shown in Table 2.3. 3 2 for a
Calculate the output power of a four cylinder, two stroke engine run at 2500 rpm. The specific fuel consumption is 0.005 Kg /KW minutes. The diameter of fuel orifice Is 0.8 mm and the specific gravity is 0.875 the fuel is injected ata pressure of 14000 KPa and the pressure in the combustion chamber is 3500 Kpa over a crank travel is 20 . Cofficient of velocity is 0.87. *