pls help ASAP absolute value of torential sheer stress of the hollow steel Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). Sm steel Iel tinler dhmpum Selid circalor D= 75 my D 80 mm G GA G-1S0 EP

pls help ASAP absolute value of torential sheer stress of the hollow steel Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). Sm steel Iel tinler dhmpum Selid circalor D= 75 my D 80 mm G GA G-1S0 EP

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two circular shafts are joined together between fixed supports to resist a torsional moment of 80 kN-m as shown. Determine the absolute value of the maximum torsional shear stress of the hollow steel shaft (in MPa). 20 IN-m Sm stcel hellw circalar duminum Selid circular D= 75 mny Do- IDO mn D> 80 mm G- D GPon 6- IS0 EPa
The light rigid bar ABCD shown Is pinned at C and connected to two vertical rods. The bar was initially horizontal, and the rods were stress-free before the load P = 20 KN is applied. E200 CPa E1m 2.0 m 0.6m 1.5 m VP-20 KN Aluminum E-70 GPa A=900mm2 L-1.5 m What is the axial stress at steel rod in MPa?
The assembly consists of two red brass C83400 copper rods AB and CD having a diameter of 30 mm, a 304 stainless steel rod EF having a diameter of 40 mm, and a rigid member G. If the supports at A, C, and F each have a stiffness of k= 200 MN/m determine the average normal stress developed in the rods when the load is applied. A C -300 mm- 30 mm 30 mm B D G E 450 mm 40 kN 40 kN 40 mm F
Maxinnun allowable stress for steel - 140 MPa Maxinnum allowable stress for ahuminum = 90 MPa Maxinnun allowable stress for brouze - 100 MPa Required: Maximun safe value of axial load P Aluminum A 400 mm Bronze A= 200 mm Steel A= 500 mm 2P 4P 2.5 m 2.0 m 1.5m
2m 2m 12₂ 2m y 2N/m ✓ 2N/m 2m $ بلا
For the rivet connection shown in figure 2-4, the allowable shearing stress in the 25mm rivets is 140 MPa. Assume the plates are adequate to transmit the load to the rivets. P= 60 KN. a) Determine the shearing stress in the most stressed rivet. b) Determine the maximum allowable value of P. c) If P=80 KN, determine the minimum diameter of rivets. USE NSCP 2015. Thanks.
ok Strength of Materials donO نورا حياتها مترجر شریه ✓t مقادم نلود Dr. Mohammed Hashim Mohammed Problems tan't yorada grutegraat km). E1.x² (1) A steel rod with cross-sectional area of 150mm² is stretched between two fixed points. The tensile load at 20°c is 5 kN. What will be the stress at -20°c? At what temperature the stress will be zero? bedre α = 11.7x10 6/2 and E = 200x10² N/m².
A plate with width of 300 millimeters and thickness of 20 milimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters by 25 millimeters diameter rivets. The rivets holes have a diameter 2 millimeters larger than the rivetdiameter. The plate is A36 with yield strength F, = 248MP.. Allowable tensile stress on net area is 0.6Fy and allowable bearing stress of 1.3Fy. The rivets are A502, Grade 2, hot-driven rivets with allowable shear stress of 150MPA. 1. Detemine the maximum load that can be applied to the connection with consideration to the yielding failure in the plates. 2. Detemine the maximum load that can be applied to the connection with consideration to the fracture failure in the plates. 3. Detemine the maximum load that can be applied to the connection without exceeding the allowable shearing stress in the rivets. 4. Detemine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between…
idity modulus doengro 17. A 12 mm thick plate is conected to two 8 mm thick plates, on either side through a 16 mm diameter power driven field rivet as shown in the figure below. Assuming permissible shear stress as 90 MPa and permissible bearing stress as 270 MPa in the rivet, the rivet value of the joint is as aeqml 19WOL to da odt ons aasmos m noienet ni mioj по djiw YIVO P/24 F 12mm ↑ P/2 00 8mm 8mm
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
1/2 Problem 1: Two solid cylindrical rods AB and BC are welded together at B and loaded as shown in. If the stress must not exceed 14OMPA in either rod, determine the smallest allowable value of the diameter of rod AB and ВС. 300mm B 40 kN 250mm - d2 30 kN
2) A solid rod with the given dimension shown in Fig. Axial loads are applied at the positions indicated. Find the f a) The max Compressive stress in the system P-60 kN Aluminum A=400 mm b) The max Tensile stress in the system P-60 kN Steel A = 500 mm² Bronze A-200 mm² 4P 2.5 m 1.5 m 2.0 m 2P