2. The bar shown weighs 20 lb and is pivoted about a point C that is 1 ft from end B. The other end is pressed against a verticalspring until the spring is compressed 2 in for the position shown. The rod is released from this position, and then comes to avertical position.For a spring constant between 800 and 2000 lb/in, plot the angular velocity of the rod at the vertical position vs the springа.constant. Use increments of 100 lb/in.b. When the rod passes through 30 degrees above the horizontal, find the tangential component of the reaction at O.6 ft1 ft +B

Use Energy Conservation: T1 + V1 = T2 + V2Vie = T2 + V2g12 k x12 = 12 m v62+ 12 I6 w2+ mg( 1.5)12…

Answered: pont pressed 2 in for the position veen…

Engineering

Mechanical Engineering

pont pressed 2 in for the position veen 800 and 2000 lb/in, pl of 100 lb/in. ugh 30 degrees above the h

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. The spring-toggle system is in the vertical plane and is held at rest with 45° when a moment of 12 N-m is applied at point C. In the initial position, the spring, with stiffness of 140 N/m, is stretched 150 mm. Bar AB has a mass of 3 kg, and bar BC has a mass of 6 kg. Find the angular velocity of BC at the moment when 8-0. Neglect friction effects. 250 mm 250 mm OB 250 mm
In the mechanism shown below, the wheel is pinned at the center. The radius from O to C is 0.2 m and link CB is 0.55 m long. CB makes an initial angle of 25° with the horizontal as shown. The hydraulic ram at B is moving left at 7 m/s. At the moment shown, what is the angular velocity of link BC and the wheel pivoted at 0? 0000 Ninbet tatis rad/s
A gear of mass m = 10 kg and radius R=0.25 m may rotate about its center of mass C, which is fixed. A rack of mass m = 10 kg is subjected to a constant force Fo = 20 N, as shown. The rack and gear are geared together (gear teeth not shown), so that the force Fo drives the rack to the right and rotates the gear. Find the angular ácceleration a of the gear and find the force f exerted by the rack on the gear. The gear is to be modeled as a uniform circular disc. Fixed Fo3 20 N Rack
The wheel shown below has a mass of 5 slugs and a radius of gyration for the z-axis through point Cof 0.7 ft. The spring is massless and has a modulus of 20 lb/ ft and a natural (unstretched) length of 4 ft. Use the acceleration due to gravity, g = 322 ft/sec. The wheel is released from rest, and it rolls without slipping on the plane. Find how far down the plane the mass center Cwill move. Cord wrapped ´around hub IT 1.3 ft 0.8 ftC 3 ft 3 4 0.5 ft
In a four bar mechanism the link AB rotates with angular velocity of 20rad/s and angular acceleration of 100 rad/s both in clockwise direction when it make an angle of 45° with link AD which is fixed .The length of various linkages are AB=CD=400 mm,BC=500mm and AD=750mm .Neglect the gravitational effect and friction.The mass of link is 5kg/m. Find the torque on output link E (2) (4) A (1) (1)
cylinder F. The follower has a velocity of 2 m/s to the right when angle e = 30°. Cam Question 3: The horizontal motion of the spring-loaded follower E, which is always in contact with the cam A is controlled by the air pressure in the horizontal pneumatics Follower 100 mm 200 mm Figure 2: Follower-cam mechanisms 3.1. Calculate the downwards velocity of the roller D in the vertical guide and the angular velocity of the link ABD for this position. 3.2. If the initial velocity of the follower E is zero when angle e = 30° and reaches the final velocity of 2 m/s after 0.5 seconds, calculate the acceleration of the roller D.
In the mechanism shown below, points E and B have the same vertical coordinate. Find the velocities of points B. C, and D of the double-slider mechanism shown in the figure if Crank 2 rotates at 42 rad/s CCW. And all forces acting. D 6. EA - 0.55" AB - 2.5" AC - 1.0" CB = 1.75" CD - 2.05" 0.75"- 4 3 60 A
The thin rectangular block is supported at its corners by small rollers resting on smooth horizontal surfaces. If b=0.5 m and h= = 0.3 m, calculate the magnitude of the angular acceleration of the block at the moment when the supporting surface at B is suddenly removed. Present your answer in rad/sec² using 3 significant figures. AC B
The spring-toggle system is in the vertical plane and is held at rest with = 45° when a moment of 12 N-m is applied at point C. In the initial position, the spring, with stiffness of 140 N/m, is stretched 150 mm. Bar AB has a mass of 3 kg, and bar BC has a mass of 6 kg. Find the angular velocity of BC at the moment when = 0. Neglect friction effects. Type here to search ThinkVision Tab Caps Lock Eve Q FI W S 3 F₂ E D 4 F3 R % 5 F4 T F G 6 Y H F$ 7 U F6 8 F7 ( 9 FB Fa F10 F11 F12 - Backspace Enter Print Screen Sya Ra Insert 250 mm Scroll LOCK 00 Delete Home End Pause Break Page Up Page Down A Num Lock 7 Home 250 mm OB 250 mm O 37°F Cloudy 2:12 PM ^4 11/16/2022 Lenovo Polp
The dimensions of the various links of a mechanism, as shown in Fig. 3, are as follows: OA = 0.3 m: AB = 1 m: CD = 0.8 m; and AC = CB. If the crank OA rotates at 100 rpm. in the anticlockwise direction, find, for the given configuration: 1. velocity and acceleration of B and D: 2. angular acceleration of the links AB and CD. 45 0.6 m- Eig 3
In the figure, the wheel rolls with no slippage at the angular velocity shown. Based on the IC of the system as shown, determine: a. The angular velocity of bar AB with respect to time b. The speed of the slider at B
At the moment shown in the figure, it is known that the rod in the vertical direction moves downward with a speed of v=0.8 m/s ederken and has an acceleration = 1.2 m/s2 upward. At this moment in question: a. The angular velocity of the AB rod, b. Bis the speed of the sliding bearing. c. The angular acceleration of the AB rod, d. Find the acceleration of B sliding bearing. Note: Take the R as 0.4m.