Problem 1: The truss shown below is made of fiberglass member section and an axial strength of 14 MPa, and is assembled with high strength nylon pins with a 20 mm diameter and a shear strength of 25 MPa. The ends of the members are reinforced. If the structure requires a minimum safety factor of 2.5, find the largest load P that can be safely applied at point A. E Ao

Problem 1: The truss shown below is made of fiberglass member section and an axial strength of 14 MPa, and is assembled with high strength nylon pins with a 20 mm diameter and a shear strength of 25 MPa. The ends of the members are reinforced. If the structure requires a minimum safety factor of 2.5, find the largest load P that can be safely applied at point A. E Ao

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

View Policies Current Attempt in Progress The pin-connected structure consists of a rigid bar ABCD and two axial members. Bar (1) is steel [E = 219 GPa, a = 11.2 x 10-6/°C] with a cross-sectional area of A1 = 470 mm?. Bar (2) is an aluminum alloy [E = 74 GPa, a = 22 x 10-6/°C] with a cross-sectional area of A2 = 280 mm?. The bars are unstressed when the structure is assembled. Assume L=790 mm, a= 310 mm, b=630 mm, c=790 mm, and P=44 kN. Aftera concentrated load of P = 44 kN is applied and the temperature is decreased by 71°C, determine: (a) the normal stresses o1, 0, in bars (1) and (2). (b) the vertical deflection vp of the rigid bar at D (positive if down, negative if up). A (1) (2) P Answers: (a) o1 = i MPa, o2 = i MPa. (b) VD = i mm.
It is a system that is composed of combination of interconnected structural elements and is used to support various loadings. Group of answer choices Statically determinate system Structural system Load analysis system Truss system
Compute its bending stresses if it is safe from wide beam shear
Dctcrminc the cxtcrnal forces acting on mcmber BG at points B, C, F and G of the composite structure shown below. 60 kN OF E 3 m od dgo o noleatm 1 m 1 m 4 m 1 m
Each of the members of the truss loaded as shown is an L 50 x 40 x 5 of A36 steel. For member BC, calculate the following: A. Stress in the member B. Strain in the member
Two T-shape sections are welded together to create a composite l-beam section as shown below. Determine the safely uniform load w (kN/m) that the beam can carry throughout its entire span. 270mm 30mm 20mm 160mm Welded Joint 130mm 30mm 135mm Beam Length = 4 m Consider the following stresses: fb(T) 3 125 МPа fb(C) = 130 MPa x at the welded joint = 20 MPa Find: 1. The Neutral Axis from the base 2. moment of inertia with respect to the horizontal centroidal axis 3. Q at the welded joint 4. Considering the maximum flexural stress in tension, WNAX is equal to KN/m. 5. Considering the maximum flexural stress in compression, WMAX, is equal to 6. Considering the stress at the welded joint, wMex is equal to kN/m.
It is a system that is composed af combination of interconnected structural elements and is used to support various loadings. O Floor systern O Lateral supporting system O Truss system Structural system • Previous Next
A flexural member is fabricated from two flange plates 1/2 x 16 and a web plate 1/4 x 20. The yield stress of the steel is 50 ksi.
Asiacell|Asiacel K/s Asiacell For simply supported beam with rectangular cross section shown, determine the values and location of the maximum tensile and compressive bending * stresses 1000 lb 400 lb/ft 6 in DV 8 in 10 ft RA Rp
A bronze bar is fastened between a steel bar and an aluminum bar as shown in Fig. p-211. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use Est = 200 GPa, Eal = 70 GPa, and Ebr = 83 GPa. Steel A = 480 mm² 1.0 m Bronze A = 650 mm² 3P 4P 2.0 m Figure P-211 Aluminum A = 320 mm² 1.5 m 2P
The double - riveted joint connects two plates which are each 3.0 mm thick, and the rivets have a diameter of 4 mm., if the failure strength of the rivets in shear is 370 N/mm2 and the ultimate tensile strength of the plate is 465 N/mm?, determine the necessary rivet pitch b (mm) if the joint is to be designed so that failure due to shear in the rivets and failure due to tension in the plate occur simultaneously. Calculate also the joint efficiency n (%). 3 mm 4 mm diameter
The pin-connected structure consists of a rigid beam ABCD and two supporting bars. Bar (1) is an aluminum alloy [E = 60 GPa] with a cross-sectional area of A1 = 870 mm?. Bar (2) is a bronze alloy [E = 92 GPa] with a cross-sectional area of Ay = 520 mm?. Assume L$=2.6 m, La=2.9 m, a=0.7 m, b= 1.3 m, and c= 1.1 m. All bars are unstressed before the load P is applied; however, there is a 3.9-mm clearance in the pin connection at A. If a load of P= 58 kN is applied at B, determine: (a) the normal stresses 01, 02, in both bars (1) and (2). (b) the normal strains € , E2, in bars (1) and (2). (c) determine the downward deflection vA of point A on the rigid bar.