PROBLEM 2 (35%). Determine the maximum force (tension or compression) at member IH of a two-side bridge truss due to a series of concentrated load shown. Assume the loads can travel in either direction along the center of the deck, so that half its load is transferred to each of the two trusses. /KKKN. U kN U kN TkN Y m M Ym V m W m Xm Xm

PROBLEM 2 (35%). Determine the maximum force (tension or compression) at member IH of a two-side bridge truss due to a series of concentrated load shown. Assume the loads can travel in either direction along the center of the deck, so that half its load is transferred to each of the two trusses. /KKKN. U kN U kN TkN Y m M Ym V m W m Xm Xm

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.9P

See similar textbooks

Similar questions

H.W. #4: A pin connected truss is loaded and supported as shown, determine: a) The normal stress in member DE if it has a cros ectional area of 750 mm². b) The minimum cross sectional area for member BC if the normal stress is limited to 30 MPa. -3m- 10 kN -3 m 15 kN 3m 3m
Each bar of the truss has a rectangular cross section, 30 mm by 60 mm. Determine the maximum vertical load P that can be applied at B if the working stresses are 100 MPa in tension and 80 MPa in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) B 8m Gm 10m
1. Zero Force Members B T АЯ Identify the Zero Force Members in the Truss Structure below. C D E F G P INA MA O M L H 500lbf Q K
Determine the force in member CE of the truss below. Indicate as positive if the member is in tension and negative (-) if the member is in compression. Provide the answer in kN G 3 m 1981 A E 1839 B -2 m- ce po C 5 kN -2 m- -2 m- 5 kN D 5 kN
SOLVE FOR THE FORCE IN ALL MEMBERS OF THE TRUSS. SHOW SOLUTIONS CLEARLY USING METHOD OF JOINTS AND WRITE WELL. 0.8m 2.4m A BD BD 3 KN MEMBER AB AC BC BE BF EF GE FG 2m Av(REACTION @ hinge) Gv(REACTION @ roller) C 1m 10KN B 1m 8KN 3.5m SUMMARY OF RESULTS FORCE E 8KN 1m F 2.4m 6KN G NATURE(T or C)
Link AC is made of a steel with a 450-MPa ultimate normal stress and has a 6 x 12-mm uniform rectangular cross section. It is connected to a support at A and to member BCD at C by 8-mm diameter pins, while member BCD is connected to its support at B by a 10-mm diameter pin. All the pins are made of steel with a 170-MPa ultimate shear stress and are in single shear. Kwing that a factoaety f32is desired. 12 mm 200 mm It is required to determine the largest load P that may be applied at D. Note that link AC is not reinforced around the pin holes. 150 mm 10
DETERMINE THE STRESS IN EACH MEMBER OF TRUSS LOADED AND SUPPORTED AS SHOWN. - 4m Am 104N D 10 KN 4m Epanels@4m = 20m E B 4m LL G 604N → 60 kN
Where is/are the location(s) of the maximum transverese shear stress? A simple I-beam is loaded as shown. 20 mm P KN PKN PKN Į Į -C B с D L/4 m L/4 m Midspan at point C Roller at E at the NA Section B at the top fiber Pin A at point C Midspan at point D Roller E at point D L/4 m L/4 m OE 20 mm 20 mm- 250 mm 150 mm 150 mm A
How many zero-force member on the structure as shown below. a.) F F F b.) 1 kip 0.5 kip 3 kips 2 kips H 2 kips 1.5 kip D M R
PROBLEM 2 Determine the internal force of the following members in the structure below. [ Select ] 1. DF [ Select] 2. DE [ Select ] 3. CE 20 N 40 N 40 N F 20 N D B 2 m C E G 10 m Ko OL No 4 m 4 m-- 2m -|- 2m 4 m
1.) Determine the force in each member (and identify whether it is compression or tension) of the truss supporting a floor deck as shown. The deck is simply supported on floor beams which, in turn, are connected to the joints of the truss. Thus, the uniformly distributed loading on the deck is transmitted by the floor beams as concentrated loads to the top joins of the truss. Floor beam Deck B 15 kN/m C ID F G H -2 m--2 m--2 m-+-2 m-+-2 m-+-2 m-+-2 m-+-2: m ET 2 m
Determine the force in member AB of the truss below. Indicate as positive if the member is in tension and negative (-) if the member is in compression. Provide the answer in kips t H 1.5 k F 2 k 2 k G B C . 8 ft 8 ft -8 ft 8 ft E D 4 ft Q Search securySearch 5 17 & 8