Problem 2. In a certain (hypothetical) communication system we find thereceived signal at the input to a signal detector isr = ±A+nwhere +A and -A occur with equal probability and the noise variable n hasprobability density functionp(n) = {n+1,1-n,1≤ n ≤ 0,0

a) To determine the smallest value of A that yields a probability of decision error less than or…

Answered: Problem 2. In a certain (hypothetical)…

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

B) A signal f(t) = 2e-atu(t) is applied to the input of system have frequency transfer function Determine the required relations between the constant a and b such that exactly |H(w) = %3D Vw² +b? 50% of the input energy on a 1 ohm basis, is transferred to the output.
A sinusoid signal v(n) = 5 sin( @₂ .n) with f=5 Hz and fs = 10 kHz has to be quantized @ (Vq(n) = Q[v(n)]) with a midtreat quantizer. The range of the signal is ±5 V and the word length of the quantizer 4 bits. The quantizer is at digital full scale. (a) How many quantization levels L does the quantizer have? What is the value of A? (b) Sketch the input-output characteristic of the quantizer. How different is a midtreat quantizer to a midrise quantizer. (c) For time index n = 1250 calculate the quantized value v₁ (n), the quantization error eq(n) and represent vą (n) using RZ code. (d) Calculate the power P of the quantization noise. (e) Determine the SNR in dB.
- at Hw. A signal FLE) = 2e ult) is applied to the input of System huve frequency transfer funehium IHlw)l = Determine the required relutionsibetween the Constants a und b Such that exactly 50% of %3D the input energy on a 1-ohm basis , is transffered to the output
x(+)= t(uC+) -uct-1) -4-1)uCt-1) + e act-i) uct-1) Closed fom expression of sc +) act-1) is x (4) = ēact fon t othorwise setting a =1 ,woite that plots the output Signal by evaluating e MATLA B soript a the closed fonm expression between t=0 and t=5 seconds blw the data points ; .e at t=0,0.01,0.02,0.03-.Seconds evaluating
For the signal x[n] shown in the following figure, sketch y[n] = x[-2-n] x [n] ... ... -3 F1 J0 1 2 3 4 5 6 7
Q1: Draw the froquency spectrum of an analog signal to be converted into a digital signal ( maximum Frequency equal to SKH2 ) if i) fs> 20% from nyquist frequency. il) fs < 20% from nyquist frequency. ili) s- 20% from nyquist froquency aluin one of its
Let x[n] be a signal with x[n] = 0 for n < -2 and n > 4. For each signal given below, determine the values of n for which it is guaranteed to be zero. (a) x[n- 3] (b) x[n + 4] (c) x[-n] (d) x[-n + 2] (e) x[ - n- 2]
A continuous analog signal x(t) is sampled with a sampling rate of 600 Hz. The sampled signal is a discrete signal x[n]. When calculating the DFT of N points of x[n], we want to be able to see frequencies separated by, at most, 0.8 Hz. (Resolution = 0.8Hz) Determine the smallest N value that satisfies the above condition.
4 The Probability density funetron (PA) of a signal îs ginen by Pcx) z ke theruse 0) what Ts the step size (9) if threere are 24 quantitatron levls- b) fmd the vodue f Conflont K I need step by step solution
Discrete Signals and Discrete Time systemsx[n1] = (values) 9 random integer values from -10 to 5x[n2] = (values) 9 random integer values from -5 to 5 a. Plot the graph setting the middle integer value at n = 0 showing the all samples.b. Plot the graph x[-n] showing all the samples.c. Plot the graph x[n-3] showing all the samples.d. Plot the graph x[n+2] showing all the samples.e. Plot the graph x[2n] showing all the samples.f. Plot the graph x[n/3] showing all the samples.g. Evaluate the convolution of x[n1] and x[n2].
4. Find N-point DFT for the signal h: hy = 8[k – 1] + 1.9 8[k – 6].
Problem 3 A linear delta modulator is designed to operate on speech signals limited to 3.4 kHz. The specifications of the modulator are as follows: > Sampling rate = 10fxyquiatɔ where fxyqpuine is the Nyquist rate of the speech signal. > Step size A = 100 mV. The modulator is tested with a 1-kHz sinusoidal signal. Determine the maximum ampli- tude of this test signal required to avoid slope overload.

SEE MORE QUESTIONS

Recommended textbooks for you

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Introductory Circuit Analysis (13th Edition)

Electrical Engineering

ISBN:

9780133923605

Author:

Robert L. Boylestad

Publisher:

PEARSON

Delmar's Standard Textbook Of Electricity

Electrical Engineering

ISBN:

9781337900348

Author:

Stephen L. Herman

Publisher:

Cengage Learning

Programmable Logic Controllers

Electrical Engineering

ISBN:

9780073373843

Author:

Frank D. Petruzella

Publisher:

McGraw-Hill Education

Fundamentals of Electric Circuits

Electrical Engineering

ISBN:

9780078028229

Author:

Charles K Alexander, Matthew Sadiku

Publisher:

McGraw-Hill Education

Electric Circuits. (11th Edition)

Electrical Engineering

ISBN:

9780134746968

Author:

James W. Nilsson, Susan Riedel

Publisher:

PEARSON

Engineering Electromagnetics

Electrical Engineering

ISBN:

9780078028151

Author:

Hayt, William H. (william Hart), Jr, BUCK, John A.

Publisher:

Mcgraw-hill Education,

SEE MORE TEXTBOOKS

Problem 2. In a certain (hypothetical) communication system we find the received signal at the input to a signal detector is r = ±A+n where +A and -A occur with equal probability and the noise variable n has probability density function p(n) = { n+1, 1-n, 1≤ n ≤ 0, 0