PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10%/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa a = 17.3 x 10°/°C

PROBLEM NO. 4 In Fig. 4, determine the normal stress and change in length of the aluminum rod if the temperature was raised by 129 C. The 0.5-mm gap exists at 28 C (0.59 mm 399 mm A Aluminum A = 2888 mm² E = 75 GPa α = 23 x 10%/°C 258 mm B Stainless Steel A = 899 mm² E = 190 GPa a = 17.3 x 10°/°C

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

! Required information At room temperature (20°C), a 0.5-mm gap exists between the ends of the rods shown. The temperature eventually reaches a value of 137°C. 300 mm Aluminum A = 2000 mm² E = 75 GPa a = 23 x 10-6/°C 0.5 mm 250 mm B teel A = 800 mm² E = 190 GPa a = 17.3 x 10-6/°C Determine the normal stress in the aluminum rod. The normal stress in the aluminum rod is EMPa.
Problem 3 An alloy bar 6m long is held between two supports by a steel rod 25 mm diameter passing through metal plates and nuts at each end.. The rod is held at temp. of 100 0 C.Determine the stress in the rod, when the temperature falls down to 60 0 C, if (i) do not yield (ii) yield by 1 mm. Take the value of e and alpha for the alloy as 200 GPa and alpha = 12x10-6 /K. %3D
The state of stress at a point in a circular bar under pure torsion is given by T xy = T yx= t and other stress components are equal to zero. The octahedral stress at the point is (a) principal stress is o 1= (b)_ and the maximum
A 12mm thick steel tire has a width of 110mm and has an internal diameter of 800mm. The tire is heated and shrunk to a steel wheel 800.5 mm in diameter. The modulus of elasticity E = 200 MPa. a. Determine the tensile stress in the tire. b. Determine the compressive pressure between the tire and the wheel. c. Determine the thickness of the tire to resist a pressure of 1.5 MPa if it has an allowable stress of 124 MPa. I need answer ASAP. Thank you!
The horizontal steel rod, 2.5 m long and 1200 mm2 in crosssectional area, is secured between two walls as. If the rod is stress-free at 20_C, compute the stress when the temperature has dropped to _20_C. Assume that (1) the walls do not move and (2) the walls move together a distance Δ = 0.5 mm. Use α = 11.7x10-6 oC and E = 200 GPa.
The structure shown below is made of 3 circular rods, each with a diameter of 1.0" and lengths as shown in the diagram. Rod AB is aluminum (E = 10E6 psi) and rod BC is steel (E = 30E6 psi) and rod CD is brass (E = 15E6 psi). The structure is axially loaded as shown in the diagram. Determine the maximum stress and its location and the change in length of the structure due to the applied loads. You may ignore the flanges that connect the rods (considered rigid). A 4 ft B 900 lb 6 ft 300 lb 2 ft C D
Bar of steel, (yield strenght Sy = 474 MPa) is subjected to the following stresses; σx = 194 MPa , σy = 100 MPa , τxy = 210 MPa Using the Maximum Shear Stress Theory (MSS) determine the factor of safety and check is the bar will fail or not.
In a volume element with dimensions dx, dy, dz the negatíve y-face has a 2 MPa stress in the positivex-direction, a 3 MPa stress in the negative z-direction, and a 4 MPa stress in the negatíve y-direction. Which of the following describes the stresses per elasticity convention? Oyy = 4 MPa Oyr = -2 MPa 3 MPa A MPa
The pipe assembly shown is subjected to a force F = 7 kN and P = 14 kN. It is made of steel with Sy = 250 MPa. Determine the safety factor at point H using the maximum shear stress theory. Select one: a. NH = 6.427 b. NH = 3.570 c. NH = 5.355 d. NH = 4.590
a=2.1m (1) c = 2m b = 3.1m d = 1.8m P = 80 kN WHAT IS THE AXIAL STRESS IN ROD 1 ? ANSWER IN MPa ROUNDED-OFF TO 2 DECIMAL PLACES B dia. of rod 1: = 13mm dia of rod 2 = 11 mm
N = 400 N T= 1.8 N-m In order to drill an 8mm hole into a block of steel, a Normal Load of 400N and Torque of 1.8 N-m must be applied to a drill bit. The drill bit H D = 8mm has a diameter of 8mm and is a solid cylinder at point H. Write the stress state for the element H pictured in the diagram.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown. The normal stress in aluminum rod (1) must be limited to 20 ksi, the normal stress in brass rod (2) must be limited to 24 ksi, and the normal stress in steel rod (3) must be limited to 12 ksi. Determine the minimum diameter required for each of the three rods. Assume P = 8 kips, Q = 5 kips, R = 20 kips and S = 28 kips. Calculate F1, F2, F3 and..