Answered: Problem: Use the elasticity theory to…

Problem: Use the elasticity theory to determine the maximum shearing stress, the angle of twist per unit length, and also the warping w for the solid shaft of a circular cross-section of radius r.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.7.3P: A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at...

See similar textbooks

Related questions

Q: according to Maximum Shear Stress theory ,Calculate the factor of safety of the shaft When it is…

A: Given data: τ=60 MPaσy=300 MPa Need to determine the factor of safety.

Q: In drilling a deep oil well the drill shaft, consisting of sections of “drill rod”, is powered from…

Q: A hollow circular torsion member has an outside diameter of 22 mm and inside diameter of 18 mm, with…

A: GivenDo=22mmDi=18mmD=20mmτ=70MPa at mean diameterG=77.5GPa

Q: A 12.6 inches long key is to be used on a 210 hp, 1200 rpm, slip ring induction motor. The key is 1…

A: Given:- length of key,l=12.6 in ,width of key,b =1 in ,height of key ,h=0.75 in ,shaft…

Q: A flanged bolt coupling is used to connect a solid shaft 110 mm in diameter to a hollow shaft 100 mm…

Q: Problem #1. The 60-mm diameter shaft is subjected to torques as shown. If the applied allowable…

Q: shop plans to subject the said shaft on a loading condition as shown in the figure. If the shearing…

Q: Required information Consider a solid shaft of 1.4-in. diameter. Determine the maximum shearing…

Q: PROBLEM 2 A drive shaft running at 2500 rpm has outer diameter of 80mm and inner diameter of 60mm.…

Q: " A thick steel cylinder which has an inside diameter of 1m is subjected to an internal pressure of…

Q: PROBLEM 3. A 5-m steel shaft rotating at 1.20 Hz has 72 kW applied at a gear that is 2 m from the…

A: When an object rotate about the point due to the linear force act on the object is known as the…

Q: 03: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

A: The given question belongs to the topic Torsion of circular shafts. In this question, rotation given…

Q: A propeller shaft for a small machine is made of a solid steel bar 104mm in diameter.The allowable…

A: Solution:- G=80GPa Twist angle=2.0° L=3.5m d=104mm To find: Maximum torque applied to the shaft,…

Q: for steel, G-83 GPa. Determine the maximum shearing stress developed in each segment.

Q: Task 3: A hollow aluminum alloy 6061-T6 shaft of outer radius c = 40 mm, inner radius b = 30 mm, and…

A: Given data:

Q: W310 x 52 beam is made with a material that has a maximum shearing stress of 90 MPa. Determine the…

Q: Two steel springs with plain ends are arranged in series and supports a load. The upper spring has…

Q: PROBLEM NO. 2 A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in…

A: Given data: ◆ The bolt circle diameter: D = 250 mm ◆ The number of bolts: n = 12 bolts ◆ The…

Q: The motor shown in Fig. P6-47 develops 100 hp at a speed of 360 rpm. Gears A and B deliver 40 hp and…

A: Given, The power produced by motor, P = 100 hp The speed of the motor, n = 360 rpm The maximum…

Q: Problem 4 A 200-mm-diameter pulley is prevented from rotating relative to 60-mm-diameter shaft by a…

Q: PROBLEM 1. A hollow cylindrical steel shaft is 1.5 m long and has inner and outer diameters…

A: As per given question L=1.5m D1=40mm D2=60mm Modulus of rigidity =77gpa We have to determine a)…

Q: A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft…

Q: If a twisting moment of 10,000 lb-in is impressed upon a 1 and 3/4 inch diameter shaft, what is the…

Q: bolt having a diameter to fasten two timbers as shown in the figure load in the bolt of 34 kN. 1.…

Q: Problem 50% A solid shaft 100 mm. in diameter is to be replaced with a hollow shaft equally strong…

A: Since it is not mentioned in the question that which of the part is to be done first. Thus going…

Q: In Fig. below, the vertical shaft and the pulleys keyed to it may be considered to be weightless.…

A: GIVEN: WORKING SHEAR STRESS, τ= 64MPa diameter of disc A=250mm diameter of disc B=500mm diameter of…

Q: A machine shaft is supported on bearings 1.2 m apart is to transmit 150 kW at 300 rpm while…

A: Given Power, P = 150 kW Speed, N = 300 rpm Shear stress = 50 MPa Find Shaft diameter, d

Q: a 1.5 inch shaft has operating speed of 100 rpm and safety factor of 12. How much horsepower can it…

A: Given data:

Q: 2. It is required to transmit 70 Hp from a turbine by a solid circular shaft turning at 200 rpm. If…

Q: The handwheel shown consists of the shaft, flange, and handle. A force P = 1 kN is applied to the…

Q: -In the clevis shown in Fig. below, find the minimum bolt diameter and the minimum thickness of each…

Q: A flanged coupling rotating at 400 rpm have 4 steel bolts evenly tightened around a 100 mm bolt…

Q: A conveyor belt is driven by a 8-hp motor turning at 2,500 rpm. Through a series of gears that…

A: Given:Power of motor,P=8HP=(8×745.7)W=5965.6WSpeed of motor,N=2500rpmSpeed of belt drum motor…

Q: A machine shaft is supported on bearings 1.5 m apart is to transmit 100KW at 300 rpm while subjected…

Q: A solid circular shaft with a 2-in diameter is subjected to a vertical shearing force of V= 4 kips.…

A: The given values are - Shear force V=4kips, Diameter d=2 in , Radius R=1 in Maximum shear stress for…

Q: The members of the structure in Fig. weigh 200lb/ft. Determine the smallest diameter pin that can be…

Q: A turbine developing 15,000 Hp turns the shaft at 300 rpm. The propeller attached to this shaft…

A: P=15000Hp N=300rpm

Q: Find the power that can be safely transmitted by a flange type shaft coupling, if it has four…

A: Write the given data. n=4R=50 mm=0.050 md=12.5 mm=0.0125 mτstud=86 MPa=86×106 PaN=3600 rpm

Q: Q3: A part of gear box shaft shown in fig 3 transmit (40 kw) power through the gear located at (C).…

Q: 6. A marine turbine developing 15,000 hp and it turns the shaft at 300 rpm. The propeller which is…

Q: according to Maximum Shear strain energy theory ,Calculate the factor of safety of the shaft When it…

Q: A flat key is to be designed for 100 mm diameter shaft which will transmit 200kw at 300 rpm . If the…

A: Given: τallow=300 MPaP=200kWN=300 rpmD=100 mmwkey=10 mm

Q: A thin-walled tube having a semi circular shape has an outside diameter of 50 mm and a wall…

Q: To reduce the total mass of the assembly shown in the figure, a new design is being considered in…

Q: A W310 x 52 beam is made with a material that has a maximum shearing stress of 90MPa. Determine the…

A: As Given in Question:- Shearing Force = 90 Mpa W310*52 depth from table = 318 mm Area for this =…

Q: 3. Does the distance from the cross section neutral-axis effects the calculated shear stress? How?…

A: Given questions : Does the distance from the cross section neutral axis effects the calculated shear…

Q: If the maximum permissible shearing stress is 10,000 psi, how many 3/8'' bolts arranged in a 5''…

A: Shear stress can be understood as the force which tends to cause deformation of a material by…

Q: Q5/ An aluminum solid shaft with a constant diameter 80mm is loaded by torques shown in Fig.4.…

Q: 0. A hollow rivet has an outside diameter of 5 mm and an inside diameter of 3 mm. If the allowable…

A: Given Outer diameter, D = 5 mm Inside diameter, d = 3 mm Stress = 400 x…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

Problem: Use the elasticity theory to determine the maximum shearing stress, the angle of twist per unit
length, and also the warping w for the solid shaft of a circular cross-section of radius r.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Introduction

VIEW

Step 2: Explanation

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A motor driving a solid circular steel shaft with diameter d = 1.5 in, transmits 50 hp to a gear at B, The allowable shear stress in the steel is 6000 psi. Calculate the required speed of rotation (number of revolutions per minute) so that the shear stress in the shaft does not exceed the allowable limit.
A full quarter-circular fillet is used at the shoulder of a stepped shaft having diameter D2= 1.0 in. (see figure), A torque T = 500 lb-in. acts on the shaft. Determine the shear stress at the stress concentration for values as follows: D1= 0.7,0.8, and 0.9 in. Plot a graph showing versus D?
For the cross-section shown below, computer the rate of twist and the shear stress if a torque of 1,000 in-lb is applied and the shear modulus is 4 x 106 psi. Take the wall thickness as 0.050 in. 5" 3" 10"-
6 An elevator torque tube is made of 24S-T aluminum alloy & has dimensions of 2- by 0.083 in. Find the angle of twist if the torsional shearing stress has a value of 10,000 psi for a length of 80 in.
A 4-spline shaft and to slide when not under load has a diameter of 2.5 in. Find the compressive and shear stresses if shearing force is 2500 lbs. If hub length is 2 inches.
The figure shows a shaft carrying three gears that rotates at 1150 rpm. Gear A delivers power =10kw to a mating gear that drives a mixer. Gear C delivers power =15kw to a different mating gear that drives a circular saw. All power comes into the shaft through gear B. Draw sheardiagramand bending moment diagram. Considering only torsion, compute the body free diagram and shearing stress in each part of the shaft. Consider stress concentrations, assume the Material is 1144 OQT 1300.
Please provide a clear step-by-step solution. Thank you! A firm shaft with radius R has a maximum shear stress of 193 MPa. If a point has a stress of 16 MPa, calculate its travel distance from the shaft's centre in terms of R.
A hollow circular torsion member has an outside diameter of 22 mm and inside diameter of 18 mm, with mean diameter D = 20 mm and t/D = 0-10. Calculate the torque and angle of twist per unit length if shearing stress at mean diameter is 70 MPa. Calculate these values if a cut is made through the wall thickness along the entire length G = 77.5 GPa.
Which of the following is TRUE for a hollow circular shaft subjected to a uniformly distributed torque within the elastic range such as what is shown in the figure? a b A B C Select one: O A. The maximum shear stress along the length of the shaft will be located at the free end. O B. The internal torque will develop a quadratic distribution of shear stress along each radial line in the plane of the cross-sectional area. O C. Warping will occur due to the distributed applied torque along the member's longitudinal axis. O D. The internal shear stress varies linearly along the longitudinal axis of the shaft.
2. Solve the following problem Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm long. One is solid but the other is hollow with an internal diameter of 50 mm. Both are made from steel (G=120 GPa). Critically evaluate and compare the torsional shear stress, angle of twist of the two designs if they are subjected to a torque ofT 171N.m the missing Torque 171(T).
302. Two solid shafts of different materials are rigidly fastened together and attached to rigid supports as shown in Fig. 3-4. The aluminum segment is 75 mm in diameter, and G, 28 X 10° N/m2. The steel segment has a diameter of 50 mm and G, 83 x 10° N/m². The torque, T 1000 N. m, is applied at the junction of the two segments. Compute the maximum shearing stress developed in the assembly. %3D %3D 3 m 1.5 m Ta Aluminum Steel T=1.0 kN m 75 mm dia. Ga 28 GN/m2 50 mm dia G, = 83 GN/m2 न
6. A marine turbine developing 15,000 hp and it turns the shaft at 300 rpm. The propeller which is attached to the shaft develops a thrust of 150,000 lbs. A hollow steel shaft with an outside diameter of 14 in. will be used. The maximum shearing stress based on the torsion alone is not to exceed 7.5 ksi. Find the thickness of the hollow shaft in mm.