Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split tensile strength (in MPa, round off to one decimal place) of the specimen is?

Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split tensile strength (in MPa, round off to one decimal place) of the specimen is?

Materials Science And Engineering Properties

1st Edition

ISBN:9781111988609

Author:Charles Gilmore

Publisher:Charles Gilmore

Chapter11: Fracture And Fatigue

Section: Chapter Questions

Problem 11.4P

See similar textbooks

Related questions

Q: For a model to be an exact replica of the prototype, we apply a. Identical dimensioning b. Unit mass…

A: Answer There are three types of similarity to exist between the model and prototype a) Geometric…

Q: In a drained triaxial compression test, a sample of sand fails at deviator stress of 150 kPa under…

A: Given data- A drained triaxial compression test- Confining pressure- σ3=50 kPa, Deviator stress-…

Q: A farm is located at longitude 121.437 degrees east and latitude 30.746 degrees sc Using ARR2016,…

A: ARR is a national guideline document, data, and software that can be used for the estimation of…

Q: GON JORN 10KN A ↓ B с Aum 4m 42m 2m² TUM Support xxn at B 3m ISKN 3m ROKN SKN 8kN DLE 2m 2m Apm tin…

Q: Solve the reaction of Beam

A: Given data in question Loadings 60 kN point load 30 kN/m UDL Span length 14 m To find out…

Q: Q2 A truss as shown in Fig. Q2 is loaded with a horizontal force of 5 kN at joint D and a vertical…

Q: a) A 10 m B 30 kN B 50 kN C 5 m 18 kN/m C b) d) 20 kN/m 5 m 30 kN/m АПВ СУ 100 kNm 5 m 60 30 kN/m

A: As per company policy we can only answer first three questions. Kindly post other questions as…

Q: What is the aeroplane flying height to obtain the average scale of the photograph equal to 1/7200?…

A: Given data: The average scale of the photograph, S = 1/7200 Ground surface elevations vary 160 m to…

Q: (a) Find the moment of interia for area respect to y-axis. (b) Find the moment of interia for area…

Q: Select the correct y for finding the bending stress at H, given that the z centroidal axis is 5 in.…

Q: If the shear force in a beam is zero, the bending moment in this same region of the beam is O…

A: Following are the relationship between shear force and bending moment. dMdx= V As per above…

Q: Can you solve this in a different way without using mohrs formula

Q: I tried to solve the problem using your solution and got a different answer. Also where is the angle…

A: To Identify the difference in the solutions

Q: The results of a standard Proctor test are given below. Determine the maximum dry unit weight of…

Q: Given: PD = 250kips and PL = 350 kips. The member is 30 ft long with pinned end, supports and is…

A: Given, DL = 250 kips LL = 350 kips W12 section

Q: Select the beam loading that corresponds to this moment diagram. M Mo O none of the above

A: Given: Bending moment diagram (BMD) varying linearly as shown in the figure. To find: loading…

Q: (4) Calculate the horizontal displacement at point D. Note that the effect of axial forces in the…

A: Horizontal displacement at point D

Q: P.5. The truss system supports the 15-kip load. There is a pin at E and a roller at F. a) Solve for…

A: Given Data a) Solve for the tension in members BC, BG, and FG using the method of sections. b).…

Q: atch Reactor with a volume of 11.859 m³ is being used to treat liquid waste from a small seafood…

A: According to given data Every week 1.461 kg of waste is added to the reactor with water, so that…

Q: Q- A road in a hilly terrain is to be laid at a gradient of 4.5%. A horizontal curve of radius 100 m…

A: Given data- Given gradient=4.5%, Radius R=100 m, To Find- The compensated gradient (CG).

Q: Assume you are an observer standing at a point on a three lane race track. All vehicles in lane 1…

A: According to given data Assume you are an observer standing at a point on a three lane race track.…

Q: question: Use Castigliano's Theorem to determine the vertical deflection at joint C of the truss…

A: A truss is given with hinged support at D and roller support at A. E = 29000 ksi Degree of static…

Q: The cross-sectional dimensions of a beam are shown. Assume b-2.5 in., t-tw-0.25 in. and d=4.25 in.…

A: a. Bending moment b. Bending stress

Q: The mass of a cube is 128g and its specific gravity is 2. Find the length of a side of the cube.

A: Objective: To determine the side of the cube. Given: Mass of the cube (say M) = 128 g Specific…

Q: Locations where the V curve crosses the V = 0 axis are important because they indicate where the…

A: Concept used: Shear forceV= Slope of bending moment diagramdMdx V=dMdx

Q: Show your neat and complete solution LINE LENGTH BEARING LATITUDE DEPARTURE AB 732.72 N00°42'E…

Q: did you come up with 100 k-ft for the BMD? I'm probobly missing it but I'm unsure of how you got

Q: The force F in Figure A is to be replaced by a force through A and a couple whose forces act…

Q: The velocity distribution in a rectangular channel of width, B, and depth of flow, yo, was…

Q: What will be the theoretical maximum capacity (to nearest 10 units) for a single lane of highways…

A: Given, speed of the traffic stream =40 km/hr Maximum theoretical capacity of single lane highway =?

Q: c) The characteristics of a soil profile are summarized in the Figure for Question 5 c. Seepage is…

A: Given: Hydraulic gradienti=0.8 Rate of flowQ=2.84×10-4 m3s Number of layersn=4 From the figure, k1=0…

Q: A Standard Proctor Test was completed according to Method A described in Chapter 12. The following…

Q: A rectangular channel is 3.5 m wide and conveys a discharge of 15.0 m/s at a depth of 2.0 m. It is…

Q: 4. Determine the safe factored load Pu that the truss can carry based on the capacity of the top…

Q: 1. The average annual precipitation for the four sub-basins constituting a large river basin is…

A: Given Data : Precipitation, P (inches) Area, A (sq. mi) 39.0 30 44.20 275 33.40 420 28.00…

Q: Problem 1. A 2-span beam is subjected to P1= 150 KN, w1= 25 KN/m and w2= 35 KN/m as shown. Required:…

A: Given Data Find support reaction using method of member

Q: In this statics problem I am given a triangular distributed load on a cable. Attached is the given…

A: To explain the inclination(15o) shown in the given figure and its importance in the solution and to…

Q: A prestressed concrete beam of effective span 16 m is of rectangular section 400 mm wide by 1200 mm…

A: Given Data : fpu=1700 N/mm2 fcu=60 N/mm2 Aps=3300 mm2 fpe=910 N/mm2 L=16 m b=400 m d=870 m Ld=18.39…

Q: 10 ft -10 ft- G B -4 ft4 ft F 600 lb E 800 lb -10 ft- D

Q: -3 ft 3 ft 3 ft 5 30° 50 lb

Q: Q- A hydraulic press has a ram of 300 mm diameter and a plunger of 45 mm diameter. When the force…

Q: A rectangular channel has a width of 2.0 m and carries a flow of 3.0 cms. If the depth of flow at a…

Q: Târee reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common…

A: Given : Elevation of reservoir A = 80 m Elevation of reservoir B = 70 m Elevation of reservoir C =…

Q: 5. Determine the internal loads at point D & E 4 11 75 lb/ft

A: Given : Determine the internal load at point D and E ?

Q: Question 2 Calculate the magnitude of the resultant moment (in kN-m) about point D of the three 4-KN…

Q: A saturated 200 cm³ clay sample has a natural water content of 35%, shrinkage limit (SL) of 12%, and…

A: According to given data A saturated 200 cm³ clay sample has a natural water content of 35%,…

Q: Part II. Complete the table below. Unit of length is meter. For area computation, use the adjusted…

Q: A pressurized fluid is contained in a closed cylindrical tank with an internal diameter of 600 mm…

Q: Raft footing are used to support walls and columns near the property line O True False

Q: The beam shown is loaded with the triangular, rectangular and the 10kN point load. Find the…

Concept explainers

Asphalt Binders and Mixtures

Asphalt binders are subsidiary products procured during the refining process of petroleum while manufacturing gasoline, diesel, and similar petroleum products. Asphalt binders are obtained from the residue that remains after the distillation of petroleum, this residue is further subjected to steam distillation and oxidation to remove the traces of gas oil present in the residue. Certain additives or modifiers are also added to asphalt binders to alter them to suit different applications.

Question

Q- The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length
300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split
tensile strength (in MPa, round off to one decimal place) of the specimen is?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 150mm x 300mm long cylindrical concrete specimen was tested for tensile strength. The sample failed when the applied force is 150,000N. What is the splitting tensile strength in MPa?
The maximum applied load on a cylindrical concrete specimen of diameter 150 mm and length 300 mm tested as per the split tensile strength test guidelines of IS 5816:1999 is 157 kN. The split tensile strength (in MPa, (round off to three decimal place) of the specimen is
4. The state of two dimensional stress acting on a concrete lamina consists of a direct tensile stress of 6 MPa and shear stress of 4 MPa, which cause cracking of concrete. Then what will be the tensile strength of the concrete in MPa.?
A 150mm diameter cylindrical concrete specimen was tested for splitting tensile strength. The splitting tensile stress at failure is 4.14 MPa, what is the applied force in kN? The sample length is 300mm
A concrete specimen with b = d is supported at both ends 600mm apart. It is tested for flexure strength with load at midspan of 100kN and failed with a flexural stress of 52.083 MPa. What is the dimension b and d of the specimen in mm?
A 150mm diameter cylindrical concrete specimen was tested for splitting tensile strength.The splitting tensile stress at failure is 4.14 MPa, what is the applied force in kN?
Civil Engineering -Construction Material & Testing A block of concrete masonry unit is tested for compressive strength. The outside dimensions of the specimen are 200 mm X 400 mm X 100mm . The cross section contains three (3) hollow square, 75mm each side, with a wall thickness of 25mm. Is the CMU, considered solid or hollow. Discuss why.
A hardened concrete cylinder is tested in compression. The ultimate compressive load measured in the laboratory is 262.5 kN. If the sample is 101.3 mm in diameter, calculate the compressive strength in MPa. Round answer to 3 significant digits
Three 6 in. * 12 in. concrete cylinders with randomly oriented steel fiber contents of 0, 2, and 3% by weight, respectively. After curing for 28 days,the specimens were subjected to increments of compressive loads until failure. The load versus deformation results were as shown in Table .Assuming that the gauge length is the whole specimen height, determine thefollowing:a. The compressive stresses and strains for each specimen at each loadincrement.b. Plot stresses versus strains for all specimens on one graph.c. The modulus of elasticity for each specimen.d. The ultimate strength for each specimen.e. The strain at failure for each specimen.f. Toughness. Curves may be approximated with a series of straight lines g. Comment on the effects of increasing the fiber content on the following:i. Modulus of elasticityii. Ultimate strengthiii. Ductilityiv. Toughness
A 150mm diameter cylindrical concrete specimen was tested for compressive strength. What would be the maximum applied force in kN when the stress at failure is 41.4 MPa?
Determine the tensile steel ratio of a singly reinforced concrete beam for the following conditions using concrete strength f’c = 21 MPa and steel yield strength fy = 420 MPa. if the tensile strain is set as 0.009 upon crushing of concrete at a strain of 0.003. = [rr] (5 decimal places)
PART B 2. (a) What is the criterion of failure of reinforced concrete flexural elements? What distribution of compressive stress is normally assumed across the compression zone of a reinforced concrete beam, and how does this compare to the actual stress distribution? (b) Obtain the ultimate moment of resistance of the beam section indicated in Figure 2, if the grade of the concrete used in the section is 35N/mm?, and the yield stress of the steel is 500N/m2 s) 750 6T20 350 ST25 6T25 200 Figure 2