Q.3) You want to transmit the message +8 a. Encode this textual message into a sequence of bits, using 5-bit ASCII coding, followed by a sixth bit for error detection, per character. This bit is chosen so that the total sum of the six bits using XOR gate is one. How many total bits are there in the message? b. Assuming the bit duration c. Assuming the bit duration 10 ms, plot the NRZ-M code. 10 ms, plot the Bipolar-RZ code.

Q.3) You want to transmit the message +8 a. Encode this textual message into a sequence of bits, using 5-bit ASCII coding, followed by a sixth bit for error detection, per character. This bit is chosen so that the total sum of the six bits using XOR gate is one. How many total bits are there in the message? b. Assuming the bit duration c. Assuming the bit duration 10 ms, plot the NRZ-M code. 10 ms, plot the Bipolar-RZ code.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

4. To burn a CD-R, the laser must pulse on and off at a high speed. When running at 10x speed in mode 1, what is the pulse length, in nanoseconds (15%)? 5. Write a procedure hamming(ascii, encoded) that converts the low-order 7 bits of ascii into an 11-bit integer codeword stored in encoded (40%).
Q.3) You want to transmit the message +$ a. Encode this textual message into a sequence of bits, using 5-bit ASCII coding, followed by a sixth bit for error detection, per character. This bit is chosen so that the total sum of the six bits using XOR gate is one. How many total bits are there in the message? d. Assuming the bit duration d. Assuming the bit duration = 10 ms, plot the NRZ-L code. = 10 ms, plot the Uipolar-RZ code.
HW Use the (7, 4) Hamming code with the equations method: a. Determine the code word for the messages 1100 and 0110. b. Calculate the Hamming distance, code rate, code detection, and code correction capabilities. c. If the 6th bit of each received code word is flipped, calculate the syndrome of each one.
13) Using 7-bit ASCII coding, encode the textual message "Me" into a sequence of binary bits followed by an eighth bit for error detection. The eighth bit is added so that the number of ones in the 8 bits is an even number. a. Using a 16-ary modulation scheme, how many bits will be represented by each pulse?
B. Given "010111" a 6-bit input to DES S-boxes S4, S5, and S6, determine the output of each of these S-boxes as a 4-bit binary. C. Given the following LFSR of degree 4, determine the output generated in the first 7 clocks (clocks 0-6). FF3-FF0 are initialized as follows: FF3=0, FF2=0, FF1=1, FF0=1.
3.(a) What is minimum hamming distance? Why are redundant bits added by the sender? Name two error detecting methods. 3. (b) A sender needs to send the four data items 0x1236, 0xABCC, 0x03BC, and 0xEEEE. To avoid confusion, 0x is written in the prefix to denote that the data is in Hexadecimal. For example, 0x3456 is 3456 in hexadecimal. Now answer the following: i. Find the checksum at the sender site. ii. Find the checksum at the receiver site if there is no error.
A bit is a 0 or a 1. A bit string of length 6 is a sequence of 6 digits, all of which are either 0 and 1. (a) How many bit strings of length 6 are there? (b) How many bit strings of length 6 or less are there? (Count the empty string of length zero also.)
Question 1. and {C,D} form the two 2-bit numbers N1 and N2. The circuit will perform the difference N1 – N2 and gives output bits F (MSB) and G. Assume that the circuit never sees the combinations of inputs in which N1 is less than N2 i.e. you can regard those input combinations as don't care Consider a 2-bit binary subtractor defined as follows. The inputs {A,B} conditions. а. Fill in the truth table for F and G. b. Fill in the K-map for the minimum sum of products expressions for the function F and G.
What is the bandwidth of a signal that ranges from 2 MHz to 7MHZ? * 14 MHz 9 MHz 4 MHz 5 MHz Consider a noiseless channel with a bandwidth of 4kHz. If we want to transmit 32Kbps on this channel, the minimum number of signal levels needed is: * 8 О 16 32 64 describes the position of the waveform relative to time 0. * frequency amplitude phase voltage
(a) A bit string is a finite sequence of 0's and 1's. How many bit strings have length 7? bit strings (b) How many bit strings of length 7 begin with four O's? If a bit string of length 7 begins with four O's, then positions remain to be filled in. Since each of these positions can be filled with either a 0 or a 1, the number of bit string of length 7 that begin with four O's is (c) How many bit strings of length 7 begin and end with a 1? bit strings
00/ A compact disk (CD) records audio signals digitally by using 32- level PCM. Assume audio signal bandwidth to be 15 KHz. the a. What is Nyquist rate? b. If the Nnyquist samples are quantized into L=65536 levels and then binary coded, determine the number of binary digits required to encode a sample. c. Determine the bit rate and symbol rate at Nyquist rate. d. For practical reasons, the signals are sampled at rate above Nequist rate at 44100 samples per second. If L=65536, determine number of bits per samples required to encode the signal and transmission bandwidth of encoded signal then find resulting bit rate and symbol rate.
For each of the following problems, you should write your answer as an expression. Do not give the final numeric value. For example, if your answer is the number of 6-permutations of a set with 10 elements, you should write P(10,6) or 10!/4! or 10 × 9 × 8 × 7 × 6 × 5, but not 151200.