Q1: A circular steel rod ABCD is loaded as shown below. Use the following datato Find the maximum stress and the deformation (AL) of the rod. Take E= 200GPa.AP1L1E Dia. 1L2Dia. 2CL3P230 mm oP3Dia. 1Dia. 2P1P2P3L1L2L3Name(mm)(mm)(kN)(kN)(kN)(mm)(mm)(mm)45401003530130021001300

Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 %3D GPa. A A P1 L1 - Dia. 1 B B L2 Dia. 2 C C L3 P2 D 30 mm o D P3 Dia. 1 Dia. 2 P1 P2 P3 L1 L2 L3 Name (mm) (mm) (kN) (kN) (kN) (mm) (mm) (mm) 45 40 100 35 30 1300 2100 1300

Q1: A circular steel rod ABCD is loaded as shown below. Use the following data to Find the maximum stress and the deformation (AL) of the rod. Take E = 200 %3D GPa. A A P1 L1 - Dia. 1 B B L2 Dia. 2 C C L3 P2 D 30 mm o D P3 Dia. 1 Dia. 2 P1 P2 P3 L1 L2 L3 Name (mm) (mm) (kN) (kN) (kN) (mm) (mm) (mm) 45 40 100 35 30 1300 2100 1300

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

2. The following the truss figure, came from your Module 1. Page 9. B D F 3 m H H. E G 30 kN 70 kN 4 panels at 4 m = 16 m But this time, All the members have a cross sectional area of 850 mm². Find the normal stress of the following members а. EF b. GH c. DF
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Two members, each consisting of a straight and a quarter-circular portion of rod, are connected as shown and support a load P=135.0 lb at A P -6 in -3 in--3 in- B Determine the internal forces at point J The axial force Fis[ The shear force Vis The bending moment Mis E lb 4 Problem 07.156.b - Determine internal forces. lb A -6 in. D 3 in O 3 in. 3 in. lb in acting in the (Click to select) direction.
2.47 The negligible weight rigid bar is pinned at O and attached to two vertical rods. WI is the largest load P that can be applied without exceeding stresses of 150 MPa in t steel rod and 70 MPa in the bronze rod, assuming the rods were initially stress-free? 4m 3m 3m Steel A = 600mm2 E = 83Gpa L = 4m Steel V P A = 1800mm2 E = 200Gpa L 3m
3. The rigid bar weighs 5 kN/m, is supported as shown. The assembly is initially stress-free. Find the stress in each rod if the temperature rises 20°C after a load W = 150 kN is applied. A (mm?) a (FC) E (GPa) Steel rod 300 11.7 x 10-6 200 Bronze rod 1400 18.9 x 10-6 83 Bronze | 3 m Steel 1.5 m ►| 1.0 m 2.5 m 2 m W
The rigid bar BDE is supported by two rods AB and CD. Rod AB is made of aluminum (Eal = 70 GPa) and has a cross-sectional area of AAB= 400 mm2; Rod CD is made of steel (Esteel = 200 GPa) and has a cross-sectional area of ACD = 500 mm2. The load P = 31 kN is applied at point E as shown in the figure. [LAB = 0.3 m, LCD = 0.4 m, a = 0.2 m, b = 0.4 m] Determine the internal force of rod AB?KN Determine the displacement of point B?in mm Determine the displacement of point E?
The rigid bar AB, attached to two vertical rods as shown in Fig. is horizontal before the load P is applied. Determine the maximum value for P If the stress must not exceed: 160 MPa for steel and 80 MPa for Bronze. Then determine the vertical movement of P. BRONZE L-5 m A 500 mm E-80 GPa STEEL L-4 m A-400 mm E-200 GPa 3 m. 5 m. VP
Two 10-mm thick plate members are to be connected using straps of the same thickness and 12-mm diameter rivets as shown in the figure. Determine the average shear stress in the rivets if the maximum tensile stress on the plate members due to load "P" is 24 MPa. The members are 50-mm wide, Assuming all the rivets fill the hణేలs Strap Plate Member Pate P 4 P
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
Load P is applied to joint D and the temperature increases by 50 °F. There are two steel (E = 29*10^6 psi; a = 6.5*10^-6/°F) AD and DC and a bronze (E = 16*10^6 psi; a = 9*10^-6/°F) BD with a length of 50 inches. Each bar is a 0.75 inch diameter. Find the deformation of every rod, the displacement at D, and the stress in each rod.
A thin polymer plate PQR is deformed so that corner Q is displaced downward by a distance L = 1.45 mm to new position Q' as shown. Determine the shear strain at Q' associated with the two edges (PQ and QR). 120 mm 480 mm. P R 240 mm -2692 μrad -3352 μrad O-4917 prad -3610 μrad O-2921 urad Q 'Q' X