Q1- Attempt only five of the following: 1- IF AX=-2000 and BL= 5, when IDIV BL get executed an error occur, fix t error then justify your answer in proper comment. 2- How many bytes are following? i- The Interrupt Service Routine (ISR) address ii-The Interrupt Vector Table (IVT) 3-For INT 1Ch, Show the IP and CS of the ISR that could be existed.

Q1- Attempt only five of the following: 1- IF AX=-2000 and BL= 5, when IDIV BL get executed an error occur, fix t error then justify your answer in proper comment. 2- How many bytes are following? i- The Interrupt Service Routine (ISR) address ii-The Interrupt Vector Table (IVT) 3-For INT 1Ch, Show the IP and CS of the ISR that could be existed.

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Suppose, you need to service 36 interrupts. At least how many slave-8259chips do you need to fulfil this requirement? Again, let, you need one more interrupt to servicealongside the above 36. Would you need more slave-8259? Explain shortly.
2- How many types of far jump there are in 8086/8088 microprocessor, what are they. 3- When you favor to use conditional jump and when you favor to use unconditional jump.
* The LOOP # will affect only CX O only IP All CS, CX and IP Both CX and IP non of those It can implement the complement of the interrupt flag directly True O False
What is the function of this C code snippet for PIC18FXXX? #pragma code My_HiPrio Int3D0x0008 void My_HiPrio_Int(void) { _asm GOTO chk_isr endasm #pragma code Select one: a. All of the above O b. Transfer control to main program c. Assigning 08H address for high priority interrupts O d. Transfer control to the ISR (Interrupt Sub-routine)
IF AX=-2000 and BL= 5, when IDIV BL get executed an error occur, fix this error then justify your answer in proper comment. How many bytes are following? The Interrupt Service Routine (ISR) address The Interrupt Vector Table (IVT) For INT 1Ch, Show the IP and CS of the ISR that could be existed.
The processor will put a halt to whatever it is doing when it detects a signal so that it can reply to the request. The following is the technique that was employed to deal with this situation: A "Signal of Interrupt Spooling" B "Handling of Interruptions" C "Interrupt Spooling" D Polling.
Conditional Execution using Bit Test (btfsc/ btfsc). 1.) Convert the provided code to the C language. Also explain the codes function. INCLUDE "P18F242.INC" CBLOCK 0x000 i, j ENDC org 0 goto main org 0x200 //start at address 0x200 main … movf i,f btfsc STATUS,Z goto end_if movf i,w addwf j,f end_if … rest of code … Dont copy from other post. Will get downvote if answer is copied.
1. What is deadlock? How can it occur? 2. Give an example of an interrupt request. Explain when will it occur?
[Direction: You can consult any resources such as books, online references, and videos for this assignment, however, you have to properly cite and paraphrase your answers when it is necessary.] The following figure represents both datapath and controlpath for MIPS architecture that implements most of the fundamental instrucons.
Please try to do it as fast as possible i will give you a like True or false: Interrupts eithere can all be enabled or all be disabled. An interrupt vector is the address of a subroutine that will service the interrupt. Transferring a byte in a serial mode is at least eiight times faster than transferring the same byte in parallel mode.
2- Write an assembly language program to test the contents of 5 memory locations start at (2000) if their parity is odd reset that location otherwise store FF in that location. 3- A block of 18 signed numbers stored at memory locations starting at DS:300. Write an assembly language program to transfer the positive numbers to a new memory locations starting at DS:500, and the negative numbers to memory locations starting at DS:400
Write a code to add two numbers stored in physical addresses 18638H and 15688H respectively in 8086 using direct addressing mode and store it in the physical address of 22000H. Assume DS =1512H.