Q1. Assume that your student number is in the following format - Student_Number _SN= abcdefghi where each letter correspond to a decimal number. For example, if the student number is SN=123456789, then a-1, b=2, c=3, .i=9. You are supposed to design a circuit as described below The circuit has one input X and one output Y. There are four states, defined as f.g.h and i. in state f: if the input is 0, the output is 0 and the next state is g if the input is 1, the output is 1 and the next state is f in state g: if the input is 0, the output is 1 and the next state is g if the input is 1, the output is 1 and the next state is f in state h: if the input is 0, the output is 0 and the next state is i if the input is 1, the output is 0 and the next state is g in state i: if the input is 0, the output is 1 and the next state is f if the input is 1, the output is 1 and the next state is g Considering the data given above, a-) Derive the state table b-) Derive the state diagram c-) If your student number is odd, design the circuit using D-type Flip Flops. Otherwise, use JK Flip flops. d-) Sketch the circuit e-) Redesign the circuit as following: if you use D type FF in he first design, convert them into JK type FF. If you use JK type FF, then convert that Flip Flop into a D type FF. F-) Sketch the circuit again.
Q1. Assume that your student number is in the following format - Student_Number _SN= abcdefghi where each letter correspond to a decimal number. For example, if the student number is SN=123456789, then a-1, b=2, c=3, .i=9. You are supposed to design a circuit as described below The circuit has one input X and one output Y. There are four states, defined as f.g.h and i. in state f: if the input is 0, the output is 0 and the next state is g if the input is 1, the output is 1 and the next state is f in state g: if the input is 0, the output is 1 and the next state is g if the input is 1, the output is 1 and the next state is f in state h: if the input is 0, the output is 0 and the next state is i if the input is 1, the output is 0 and the next state is g in state i: if the input is 0, the output is 1 and the next state is f if the input is 1, the output is 1 and the next state is g Considering the data given above, a-) Derive the state table b-) Derive the state diagram c-) If your student number is odd, design the circuit using D-type Flip Flops. Otherwise, use JK Flip flops. d-) Sketch the circuit e-) Redesign the circuit as following: if you use D type FF in he first design, convert them into JK type FF. If you use JK type FF, then convert that Flip Flop into a D type FF. F-) Sketch the circuit again.
Introductory Circuit Analysis (13th Edition)
13th Edition
ISBN:9780133923605
Author:Robert L. Boylestad
Publisher:Robert L. Boylestad
Chapter1: Introduction
Section: Chapter Questions
Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...
Related questions
Question
f=2 g=0 h=0 i=8
Transcribed Image Text:Q1. Assume that your student number is in the following format -
Student_Number_SN= a bcdefghi
where each letter correspond to a decimal number. For example, if the student number is SN=123456789,
then a=1, b=2, c=3, .i-9.
You are supposed to design a circuit as described below
The circuit has one input X and one output Y. There are four states, defined as f,g,h and i.
in state f:
if the input is 0, the output is 0 and the next state is g
if the input is 1, the output is 1 and the next state is f
in state g:
if the input is 0, the output is 1 and the next state is g
if the input is 1, the output is 1 and the next state is f
in state h:
if the input is 0, the output is 0 and the next state is i
if the input is 1, the output is 0 and the next state is g
in state i:
if the input is 0, the output is 1 and the next state is f
if the input is 1, the output is 1 and the next state is g
Considering the data given above,
a-) Derive the state table
b-) Derive the state diagram
c-) If your student number is odd, design the circuit using D-type Flip Flops. Otherwise, use JK Flip flops.
d-) Sketch the circuit
e-) Redesign the circuit as following: if you use D type FF in he first design, convert them into JK type FF. If
you use JK type FF, then convert that Flip Flop into a D type FF.
F-) Sketch the circuit again.
Expert Solution
This question has been solved!
Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.
Step by step
Solved in 6 steps with 8 images
Knowledge Booster
Learn more about
Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.Recommended textbooks for you
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Introductory Circuit Analysis (13th Edition)
Electrical Engineering
ISBN:
9780133923605
Author:
Robert L. Boylestad
Publisher:
PEARSON
Delmar's Standard Textbook Of Electricity
Electrical Engineering
ISBN:
9781337900348
Author:
Stephen L. Herman
Publisher:
Cengage Learning
Programmable Logic Controllers
Electrical Engineering
ISBN:
9780073373843
Author:
Frank D. Petruzella
Publisher:
McGraw-Hill Education
Fundamentals of Electric Circuits
Electrical Engineering
ISBN:
9780078028229
Author:
Charles K Alexander, Matthew Sadiku
Publisher:
McGraw-Hill Education
Electric Circuits. (11th Edition)
Electrical Engineering
ISBN:
9780134746968
Author:
James W. Nilsson, Susan Riedel
Publisher:
PEARSON
Engineering Electromagnetics
Electrical Engineering
ISBN:
9780078028151
Author:
Hayt, William H. (william Hart), Jr, BUCK, John A.
Publisher:
Mcgraw-hill Education,