Q2- Water ( p= 990 kg/m' & u= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.

Q2- Water ( p= 990 kg/m' & u= 0.001 pa.s) is pumping from a water tank to water injection well with carbon steel pipe at the same level, where the pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.0000045 m, and water flow rate is 0.0065 m/sec. 1- Calculate discharge frictional head loss. 2- Calculate pump liquid power, if pump section head value is 3.8 m.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water flows through a 300mm diameter pipe at a velocity Of 3.00 m/s. Determine the weight flow rate in N/s. Do not write the unit. You will only jnput the numerical answer in the space provided. Unit of the Correct Answer: N/s O 9810.000 O 2,080.284 O 8829.000 1202.284
Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow rate in each pipe. The pipes characteristics are given as follows: Pipe L (m) D (mm) f A 610 152 0.020 B 488 102 0.032 C 1220 203 0.024 Good Luck -re (2) Water qure (3) EL=7om A B EL-15m
A pump is used to draw water from an open reservoir to an open tank on thetop of a building. The discharge flow rate is 50 lps. The static suction head of the pump is6 m and the static discharge head is 20 m. The cast iron, schedule 40, pipe in the suctionline is 4 inches nominal diameter and 20 m long. The cast iron, schedule 40, pipe in thedischarge line is 6 inches nominal diameter and 65 m long. The fittings and valvesinstalled in the suction line are the following: two 90o standard elbow and one gate valve.For the discharge line, are the following: one check valve, one gate valve, and three 90ostandard elbows. Assuming a water viscosity of 0.001002 Pa-s, and a pump efficiency of82 %. Determine: a) the total dynamic head b) the pump brake power. Show the neat schematic diagram of pumping system. Note: Use Moody’s equation for the value of friction factor; and table for determining the equivalent length of the components.
Q5: As shown in figure (5). What is the water horsepower of the pump? The pipes characteristics are as follows. Pipe 1 2 3 EL.0.0m D (mm) 200 300 250 L (m) 900 300 1500 0.135 m²/sec f 0.023 0.018 0.02 EL 120m EL.30m
Q2) For the pipe system shown in the figure, the flow rate is 0.00085 m³/s & v-1.14*106 m²/s, F-0.023, p=990 Kg/m³, diameter 15mm, Celbow=0.9, Cvalve -10, Cfaucet -2.Calculate the pressure at point (1)? -3.0- Faucet 4.5- -1.5- 3.0 Valve EXE 3.0 elbow 005
3)a: For the figure below, find the discharge in pipe, neglect the minor losses only. (e-0.001m, D-Im, L-600m, u-1.307*10 m/sec). LAS 5m 2 1.96 D. b: In a pipe of 300 mm diameter the maximum velocity of the flow is found to be 2 m/s. If the flow in the pipe is laminar, determine: 1) The average velocity and the radius at which having the same velocity magnitude as the average velocity. 2) The velocity at 50 mm from the wall of the pipe. 5964 11.62
... ... Example 5: The water level in a tank is 15 m above the ground. A hose is connected to the bottom of the tank, and the nozzle at the end of the hose is pointed straight up. The tank cover is airtight, and the air pressure above the water surface is 3 atm gage. The system is at sea level. Determine the maximum height to which the water stream could rise 3 atm 15 m h
fl a f P₂/ Water system show in the figure below L = 160 m, d = 100 mm Given: hp = 10 Bar djet= 50 mm Find: Q, h at point 2 Draw H.G.L and find V of flow out of the Jet. WIL. ¥5 Water Pump 0 hp 1 L=160m d=100 mm √30 f = 0.02 Open Jet 2160m T Reference line لمود
(Flow through Single Pipes). Determine the flow in each pipe and the pressure at the junction node, D. Assume elevation at Node, D to be 328 feet and friction factor, f, of 0.02 for all pipes. [NOTE: This is a three-part problem]. A B Elevation (ft) Length (ft) 19,680 Diameter (ft) Reservoir Pipe Part A) A 656 AD 3.28 В 590 BD 13,120 2.5 558 CD 29,520 2.5 19,680 13,120 Part B) A 656 AD 3.28 В 574 BD 3.28 CD 29,520 19,680 19,680 492 2.5 Part C) A 656 AD 3.28 В 590 BD 3.28 492 CD 19,680 3.28
2) A pump is used to draw water from an open reservoir to an open tank on the top of a building. The discharge flow rate is 50 lps. The static suction head of the pump is 6 m and the static discharge head is 20 m. The cast iron, schedule 40, pipe in the suction line is 4 inches nominal diameter and 20 m long. The cast iron, schedule 40, pipe in the discharge line is 6 inches nominal diameter and 65 m long. The fittings and valves installed in the suction line are the following: two 90o standard elbow and one gate valve. For the discharge line, are the following: one check valve, one gate valve, and three 90o standard elbows. Assuming a water viscosity of 0.001002 Pa-s, and a pump efficiency of 82%. Determine a) the total dynamic head b) the pump brake power. Show the neat schematic diagram of pumping system. Note: Use Moody’s equation for the value of friction factor; and table for determining the equivalent length of the components.
Installed is a venturi meter on a pipe 30 cm diameter in which the maximum flow is 2.7 cum of water in one minute. The throat is 15 cm in diameter. Compute the theoretical discharge that would be passing through the meter when the differetial manometer is as shown. Calculate also the discharge coefficient, C.
A liquid whose specific gravity is 2.0, is flowing in a 50mm diameter pipe. The total head at a given point was found to be 17.5m. That point is 3m above the datum and the pressure in the pipe is 65.6KPA. Compute the discharge in that point of the pipe. (A 19.28 L/s B No Answer among the choices 24.31 L/s D 29.05 L/s (E 32,56 L/s