Q3: The following loads are connected to a common supply: Load A: 150 kVA at 0.707 power factor lagging. Load B: 100 kW at unity power factor. Load C: 75 KVA at 0.8 power factor lagging. Load D: 50 kW at 0.6 power factor leading. Determine the total apparent power and the overall power factor. How can you improve the power factor to unity?

Q3: The following loads are connected to a common supply: Load A: 150 kVA at 0.707 power factor lagging. Load B: 100 kW at unity power factor. Load C: 75 KVA at 0.8 power factor lagging. Load D: 50 kW at 0.6 power factor leading. Determine the total apparent power and the overall power factor. How can you improve the power factor to unity?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Similar questions

Is the power factor in Question 6 a leading or lagging power factor? Explain your answer.
Q2. For the circuit shown below, sketch the current waveforms is and io and determine the Average and RMS for both currents. a = 50° T1 50 2 ot Vs = 300 sin 100rt T2 ot
The power factor of the circuit shown in figure 2 is. a. 0.866 lagging b. 0.5 lagging c. 0.707 lagging d. 1
15 A of current is taken by a non-inductive load at 125 V. In order that the same current shall be generated from 240 V, 50 Hz mains. An inductor is now also then connected in series. Note: The resistance of the inductor should be ignored and also assume the waveform to be sinusoidal. Determine the phase difference between the current and the applied voltage, the impedance of the circuit and the inductance of the inductor.
Power factor is leading if a. load absorbing reactive power Ob. load is inductive C. voltage lags current d. voltage leads current Clear my choice
Problem 1 • A sinusoidal source with frequency of 60 Hz and rms-voltage of 100 V is connected to an RL load of 10 ohms and 100 uH. Find Power Factor From Calculation Find Power Factor From Plot L=10mH find power factor from calculation only
d. 565.685 V If a Load absorbs 20 kVA at a leading power factor of 0.6. Then the complex power is: Select one: O a. 12000 - j16000 VA O b.-12000 + j16000 VA O c. 12000 + j16000 VA O d. None of these Given the circuit below and the associated set of voltages and currents, the reactive Power developed by im voltage source is FENG300 MINTERM
An impedance of 10 + j80 ohms is connected in parallel with a 50 ohms resistor across a 230V ac source. What is the power factor of the circuit? a. 0.95 b. 0.84 c. 0.87 d. 0.92
1 Calculate average and RMS value of the voltage waveform given in Figure. 4V %3D t(ms)- 4V
Find the RMS value of V)-100 sin(377t+76) V
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading