Q9. a) Design a non-inverting amplifier to have a closed loop gain of 10. The op-amp has an output saturation voltage of 10V, what is its maximum signal amplitude that can be applied to the input without saturation occurring? b) If the output of the op-amp is connected to a load of 5k9, what will be the output current from the op-amp when the maximum voltage is observed at the output of the op. Amp? Note: State any assumptions made in your analysis.

Q9. a) Design a non-inverting amplifier to have a closed loop gain of 10. The op-amp has an output saturation voltage of 10V, what is its maximum signal amplitude that can be applied to the input without saturation occurring? b) If the output of the op-amp is connected to a load of 5k9, what will be the output current from the op-amp when the maximum voltage is observed at the output of the op. Amp? Note: State any assumptions made in your analysis.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider the op-amp circuit to the right. Write a general formula for Vout as a function of Vin and the parameters of the resistor and MOSFET. Make sure to pay attention to the orientation of the MOSFET, you may assume an ideal op-amp. Vin R1 om + Q1 Vout
Discuss what a difference amp is, give equations and details, what is a single-ended and differential signal, what is a 4-20 mA signal, what is common-mode noise and why is a difference amp used?
10 V(p-p),1KHz sinusoidal voltage is applied to op-amp input and non-inverting input isgrounded. What is the gain of this op-amp and why?
Answer the following questions a) What assumption do we make for an ideal op - amp? b) Explain what slew rate is why it is important characteristic for an op amp.
3F roblem 1. (P1) Three op-amps are connected in cascade configuration. An 80 microVolts signal is connected to the non-inverting input of the first op-amp. Both the 2nd and 3rd op-amps operates as inverting amplifiers. All feedback resistors are 420 KOhms while the input resistances are 71.4kOhms, 19.1kOhms, and 14KOhms respectively. Determine the output voltage of the first stage stage. a.12 V b.-1200 mV c.-1.2 V d.1.2 mV
With capacitors in this Inverting Op-Amp, how should I find worst case values of Rin and Rf?
Why is there a difference between the theoretical and practical values of voltage gain in an inverting and non-inverting Op amplifier?
3) Consider the Zener-diode voltage regulator shown below. Suppose you design this circuit to drive (supply) a load resistance RL. The supply voltages to the op-amp are +15 V and -15 V (not shown). a) What is Vout? b) If R = 1 k 2, what is the smallest R, that the circuit can handle without "sagging" the output voltage? c) What should be the power rating of the resistor R? Be explicit about your assumptions. +15 V R Vout IN4738 CS Scanned with CaScanner
Derive the expression for voltage gain of deffenetial amplifier with two op-amps.
For an op-amp having a slew rate SR=5V/ms, what is the maximum closed-loop voltage gain that can be used when the input signal varies by 0.2V in 10ms?
assume ideal op-amp Find the center frequency, BW, & the gain
An inverting amplifier has closed-loop voltage gain of 100. The op-amp has an open-loop voltage gain of 100000. If a different op-amp with open-loop gain of 200000 is substituted in the configuration, the closed-loop gain increases/decreases and why?