i need the answer quickly Q Give reason(s) for the following:1_in tensile test of plastic materials the drawn material is much stronger thanthe original undrawn plastic material.2- In load-extension curves that are obtained for many plastic materials, itwould be very difficult or impossible to obtain a value for young's modulus3- When a sample of hard material is subjected to three points bending test,the fracture commences at Lower surface.4_In compression testing, test-pieces have to be short and the length not begreater than three times the diameter.5_In compression test, once plastic deformation occurs the material tends todeform into a barrel shape6- In compression test, the shape of plastic portion of stress-strain curve isdifferent from its tensile test complement in that higher values of engineeringstress are calculated.7_In cup drawing tests, some drawn cups possess ears8_We could not use results of tensile tests to predict impact failure behavior.9- Small test pieces are not recommended for tensile test.10- It is recommended not to make more than one dynamic hardness test onthe same point on the surface.

Solution: Note: Dear Student! As per our guidelines, we are only allowed to answer three sub-parts…

Q_Give reason(s) for the following: 1_in tensile test of plastic materials the drawn material is much stronger than the original undrawn plastic material. 2- In load-extension curves that are obtained for many plastic materials, it would be very difficult or impossible to obtain a value for young's modulus 3- When a sample of hard material is subjected to three points bending test, the fracture commences at Lower surface.

Q_Give reason(s) for the following: 1_in tensile test of plastic materials the drawn material is much stronger than the original undrawn plastic material. 2- In load-extension curves that are obtained for many plastic materials, it would be very difficult or impossible to obtain a value for young's modulus 3- When a sample of hard material is subjected to three points bending test, the fracture commences at Lower surface.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In tensile test a plain carbon steel specimen has a (40mm) gauge length and the Final area (A final) of specimen after tensile test was 264.327. The load which caused fracture was (122.5 KN). After fracture, the final length was 47.516mm The true stress at fracture is less than engineering stress at fracture True False
Draw a typical stress vs strain tensile test curve for the following material and label the axis. A typical brittle material subjected to a tensile stress that has been applied to the material till the sample breaks. 1- label the axis and draw the curve for a brittle material. 2- indicate the maximum strength of the material. 3- show on the portion of the curve where young's modulus can be calculated.
For a piece of copper alloy, a standard stress test was applied to it, the following data was collected, from which a stress-strain diagram must be generated, where as data it is known that the initial diameter of the element is 0.505in. The analysis must include the following: 1.Modulus of Elasticity and modulus of resilience. 2.Percentage of elongation. 3.Percentage of area reduction. 4.Real and engineering stress at fracture. It is known that after the specimen fractures, its dimensions in terms of length and diameter are 3.014 and 0.374in, respectively.
The problem: A 13 mm-diameter tensile specimen has a 50 mm gauge length. The load corresponding to the 0.2 percent offset is 6800 kg and the maximum load is 8400 kg. Fracture occurs at 7300 kg. The diameter after fracture is 8 mm and the gauge length at fracture is 65 mm. a) Calculate the standard mechanical properties of the used specimen in the tension test, first determine the standard properties and then calculated them? This includes computation each of Yield strength. Ultimate tensile strength. Fracture stress. Ductility (percent of elongation and reduction in cross section area). b) IfE- 207 GPa, estimate the elastic recoverable strain at maximum load? ) By using the same conditions of the above test, Discussion the possibility to replace the metallic sample with ceramic sample?
The problem: A 13 mm-diameter tensile specimen has a 50 mm gauge length. The load corresponding to the 0.2 percent offset is 6800 kg and the maximum load is 8400 kg. Fracture occurs at 7300 kg. The diameter after fracture is 8 mm and the gauge length at fracture is 65 mm. a) Calculate the standard mechanical properties of the used specimen in the tension test, first determine the standard properties and then calculated them? This includes computation each of: Yield strength. Ultimate tensile strength. Fracture stress. Ductility (percent of elongation and reduction in cross section area). b) If E = 207 GPa, estimate the elastic recoverable strain at maximum load? c) By using the same conditions of the above test, Discussion the possibility to replace the metallic sample with ceramic sample? tion:
Consider the tensile stress-strain diagram below. If samples 1 and 2 are identical except that they were tested at different temperatures, which sample was tested at a lower temperature? Note: This question will be marked negatively so consider your answer carefully. A. Sample 1 B. Both were tested at the same temperature/ Alby is by die dieselfde temperatuur getoets C. Sample 2
Draw a typical stress vs strain tensile test curve for the following materials (two seperate graphs) and label the axis. A ductile metallic test specimen that is stretched to failure displaying a characteristic yield point and show the following parts on the curve. 1- Yield point 2- Ultimate Tensile Strength 3- Breaking point 4- Elastic Region 5- Plastic Region 6- Necking region
ASAP
A hot rolled steel tension test sample has a diameter of 6 mm and the original gage lenght of 30 mm. In a test to fracture, the stress and strain data below were obtained. Complete table.
The following data are obtained from a tensile test of a copper specimen. - The load at the yield point is 158 kN. - Length of the specimen is 26 mm. - The yield strength is 75 kN/mm?. - The percentage of elongation is 40 %. Determine the following (v) Final diameter if the percentage of reduction in area is 21 %. Final Area of the Specimen at Fracture (in mm) Final Diameter of the Specimen after Fracture (in mm)
Q1. (i) Initial strain Please enter your supplied question data Q1. (ii) Eo B (hr¹Pa-¹) n IVICUITO Fracture 0.003 Please enter your answers here Your Q1. (i) Answers: 4.60E-34 Q1. (ii) 3.2 Q2. o (Pa) σo (Pa) 780,000,000 Q3. t (hr) Q2. A component is made from a metal that is known to be viscoelastic and behaves according to a secondary creep rate equation with constants of B and n provided as your input values. If the component is subjected to a constant force that results in the initial strain of E provided to you, determine the design stress for a secondary creep life of 1,000 hrs before attaining a limiting strain, &, of 0.01. Q3. If the same component is subjected to a constant displacement that results in the value of initial stress, o, provided to you, calculate the time for the stress to reduce to 200MPa. Young's modulus of the bolt is E = 200GPa.
QUESTION ONE (a) Distinguish between physical and mechanical properties of materials. Give two examples of each. (b) Explain why in a stress versus strain curve, the plastic portion of the graph after necking tends to drop (ie the force drops) despite that the tension is increasing. (c) A tensile test uses a copper test specimen that has a gauge length of 80 mm and a di.ameter of 16 mm. During the test, the specimen yields under a load of 9,600 N. The corresponding gauge length is 80.24 mm. The maximum load reached is 148,000 N at a gauge length of 94.2 mm, while fracture happens at a load of 12,800 N and a gauge length of 102 6 mm Determine the following: (i) Modulus of elasticity E (ii) Yield strength Oy (iii) Fracture strength, ơt (iv) Tensile strength OTs. 1