Question 1: Consider following scenario for a program running on two computers A and B. Computer A Computer B Execution time = 10 S Execution time = 8S ClockRate = 2 GHz No of clock cycles of B = 1.1XNO of clock cycles of computer A Find out the clock rate for computer B?

Question 1: Consider following scenario for a program running on two computers A and B. Computer A Computer B Execution time = 10 S Execution time = 8S ClockRate = 2 GHz No of clock cycles of B = 1.1XNO of clock cycles of computer A Find out the clock rate for computer B?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

When purifying drinking water you can use a so-called membrane filtration. In an experiment one wishes to examine the relationship between the drop across a membrane and the flux (flow per area) through the membrane. We observe the following 10 related values of pressure (x) and flux (y): pressure 2 3 4 5 6 7 8 9. 10 Pressure (x) 1.02 2.08 2.89 4.01 5.32 5.83 7.26 7.96 9.11 9.99 Flux (y) 1.15 0.85 1.56 1.72 4.32 5.07 5.00 5.31 6.17 7.04 Copy this into R to avoid typing in the data: D <- data.frame( pressure=c(1.02,2.08,2.89,4.01,5.32,5.83,7.26,7.96,9.11,9.99), flux=c(1.15,0.85,1.56,1.72,4.32,5.07,5.00,5.31,6.17,7.04)
thermostat, which will turn the heat on when the room temperature drops h degrees below its set point, Ts, and cuts heat off at a temperature h degrees higher than Ts . The system heats at a constant rate Q (thermal units per time unit), and the volume of the room is V, so, if the room were perfectly insulated, the heating system would raise the temperature of the room at the rate KVQ (degrees per time unit), where K is a constant of proportionality giving the change in temperature per thermal unit per unit volume. However, there is a heat loss to the outside that is proportional to the difference in temperature between the room and the outside. Using the modified Euler method, write a FORTRAN program to simulate this system, if the room temperature at time is T(t), T(0) = To, and the outside temperature, Tout' is given by: Case (1) : Tout is constant < Ts Case (2) : Tout = A sin(wt + 4)| , %3D reflecting daily cycles. A is temperature range, 2n/w is the period of a cycle, and o is the…
Given a processor with a clock rate of 3GHZ and CPI of 1.5. For a program with an execution time of 10 seconds, how many clock cycles are needed? Select one: а. 20 х 10° суcles b. 45 x 10° cycles c. 10 × 10° cycles O d. None e. 30 х 10° суcles
Consider a thermostat with only one temperature threshold. In the initial state, if the temperature is less than or equal to 20 degrees Celsius, it turns the heater on and leaves it on for at least 30 seconds. After that, if the temperature is greater than 20 degrees, it turns the heater off and leaves it off for at least 2 minutes. It turns it on again only if the temperature is less than or equal to 20 degrees. Design an FSM that behaves as described, assuming it reacts exactly once every 30 seconds
Question Harry has a big wall clock, that got hit while he was playing. Now, the minute hand doesn't rotate by the angle 2t/3600 each second, but now it moves according to different angle x. You can assume that coordinates of the centre of the clock are (0, 0) and the length of the minute hand is I. One endpoint of the minute hand is always located at the clock centre; the other endpoint is initially located at the point (0, 1). One second later, Harry observes that this endpoint is at distance d above the x-axis, i.e., the y-coordinate of this endpoint is equal to d. Harry is curious about where the minute hand will be (specifically, its y-coordinate) after t seconds. Because t can be very large, Harry can't wait for that moment. Please help him to write a python code that prints a single line containing the output. Input: 422 Output 4
A beam with a length L is attached to the wall with a cable as shown. A load W = 400 lb. is attached to the beam. The tension force, T, in the cable is given by: T = WL√h²+x² hx For a beam with L= 120 in. and h = 50 in. calculate T for x = 10, 30, 50, 70, 90, and 110 in. MATLAB D W
a) Explain on Simulated Annealing algorithm behaves at very high temperatures, and how it behaves at very low temperatures. (b) Imagine the implementation of Simulated Annealing algorithm in real life. Let's say, you have a caretaker at your home. Your home has a garden and it has a fountain with a network of pipes that contains 150 faucets. You informed your caretaker that you are going for short holiday to Langkawi for 3 days and when you return you would like the fountain to spray as high as possible. Your caretaker knows that it is impossible to check all faucets within 3 days to obtain an optimal setting. You can use Simulated Annealing algorithm to maximize the height of the fountain, also can assume whether a faucet can be ON or OFF and measuring the water height. Adding to that, you can make any other assumptions required for this scenario, explain clearly using Simulated Annealing algorithm.
Correct answer will be upvoted else Multiple Downvoted. Computer science. You should stop precisely one of these boards, at any subsequent you wish. Then, at that point, the boards adjoining it get stopped one second after the fact, the boards nearby those get stopped 2 seconds after the fact, etc. At the end of the day, in the event that you stop board x, board y (for all substantial y) would be stopped precisely |x−y| seconds after the fact. For instance, assume there are 4 boards, and the 3-rd board is stopped when the digit 9 is on it. The board 1 stops 2 seconds after the fact, so it has the digit 1; the board 2 stops 1 second after the fact, so it has the digit 0; the board 4 stops 1 second after the fact, so it has the digit 0. The subsequent 4-digit number is 1090. Note that this model isn't ideal for n=4. When all boards have been stopped, you compose the digits showed on them from left to right, to frame a n digit number (it can comprise of driving…
A produce dealer has a warehouse that stores a variety of fruits. He wants a machine capable of sorting the fruit according to the type. There is a conveyor belt on which the fruit is loaded. It is then passed through a set of sensors which measure 3 properties of the fruit: shape, texture, and weight. The sensor system is somehow rather primitive: • Shape sensor : -1 if the fruit is round and 1 if it is more elliptical• Texture sensor : -1 if the surface is smooth, 1 if it is rough• Weight sensor : -1 if the fruit is > 500g, 1 if is < 500g The sensor output will then be input to a Neural Networks based classifying system. As an AI Engineer you are supposed to design (draw the architecture and determine the optimal weight W and bias b) a simple neural network (could be a single perceptron) that can be used to recognize the fruit so that it can be directed to the correct storage bin. As a startup case, the simple network will only be used for two type of fruit i.e. banana and…
A produce dealer has a warehouse that stores a variety of fruits. He wants a machine capable of sorting the fruit according to the type. There is a conveyor belt on which the fruit is loaded. It is then passed through a set of sensors which measure 3 properties of the fruit: shape, texture, and weight. The sensor system is somehow rather primitive: • Shape sensor :-1 if the fruit is round and 1 if it is more elliptical • Texture sensor :-1 if the surface is smooth, 1 if it is rough • Weight sensor :-1 if the fruit is > 500g, 1 if is < 500g The sensor output will then be input to a Neural Networks based classifying system. As an Al Engineer you are supposed to design (draw the architecture and determine the optimal weight W and bias b) a simple neural network (could be a single perceptron) that can be used to recognize the fruit so that it can be directed to the correct storage bin. As a startup case, the simple network will only be used for two type of fruit i.e. banana and apple.…
A produce dealer has a warehouse that stores a variety of fruits. He wants a machine capable of sorting the fruit according to the type. There is a conveyor belt on which the fruit is loaded. It is then passed through a set of sensors which measure 3 properties of the fruit: shape, texture, and weight. The sensor system is somehow rather primitive: • Shape sensor : -1 if the fruit is round and 1 if it is more elliptical • Texture sensor : -1 if the surface is smooth, 1 if it is rough • Weight sensor : -1 if the fruit is > 500g, 1 if is < 500g The sensor output will then be input to a Neural Networks based classifying system. As an AI Engineer you are supposed to design (draw the architecture and determine the optimal weight W and bias b) a simple neural network (could be a single perceptron) that can be used to recognize the fruit so that it can be dirccted to the correct storage bin. As a startup case, the simple network will only be used for two types of fruit i.e. banana and apple.…
Question 9 Electrical resistors are said to be connected "in series" if the same current passes through each and "in parallel* if the same voltage is applied across each. If in series, they are equivalent to a single resistor whose resistance is given by R = R, + R2 + R3 + …+ R, ... If in parallel, their equivalent resistance is given by 1 + Ro 1. 1. 1 + R2 1. R R, R3 Write an M- le that prompts the user for the type of connection (series or parallel) and the number of resistors n and then computes the equivalent resistance.