answer fast (b)10Refer to hoist system arrangement as in Figure Q1(b) and specifications details in TableQ1(b).(1)Calculate the motor torque,Examine the maximum torque delivered by motor to the drum's end, and(iii) Given the drum's radius is 150 mm and find the maximum weight of m withinthe hoist capability.9876gh press543No12Table Q1(b)DetailsElectric Motor1 gear mesh ratio2 gear mesh ratio1M2ndgear mesh efficiencygear mesh efficiencyMotor shaft momentinertia, InCenter shaft momentinertia, I,Drum moment inertia, laMotor shaft frictiontorque, TxmCenter shaft frictiontorque, TSpecifications10 kW,2800 RPM with am -0.2mrad/s0.20.20.90.950 kgm²100 kgm²500 kgm²10 Nm10 Nm MotorTxmRadius-X meterD₁TxtFigure Q1(b)1₂,D₂Drum

Answered: Image /qna-images/answer/946b8119-7bfb-4f60-b838-d43fea9f6678.jpg

Refer to hoist system arrangement as in Figure Q1(b) and specifications details in Table QI(b). (1) (iii) Calculate the motor torque, Examine the maximum torque delivered by motor to the drum's end, and Given the drum's radius is 150 mm and find the maximum weight of m within the hoist capability.

Refer to hoist system arrangement as in Figure Q1(b) and specifications details in Table QI(b). (1) (iii) Calculate the motor torque, Examine the maximum torque delivered by motor to the drum's end, and Given the drum's radius is 150 mm and find the maximum weight of m within the hoist capability.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
A narrow V-belt (wedge belt) transmits power from an internal combustion engine operating at 700 rpm to the shaft of a dough mixer (medium duty) operating at 50 rpm. The internal combustion engine develops a nominal power of 50 kW and the dough mixer operates for no more than 8 hours per day. Which of the following belts can be used for this application? Hint: First determine the design load by using an appropriate service factor from page F12 in Appendix H in the Design Manual. SPC only SPB or SPC SPA or SPB SPB only
Problem 4. For the belt drive shown below calculate the contact angle 0, if: D %3D 100 mт; d 3 30 тm; C = 300 mm. D-d 20 sin V4c² - (D – d)²- -1 D-d sin 20 Op
The factor of safety against slipping in the friction clutch = 1.3; coefficient of friction=0.3; working speed= 600 rpm; friction surface number= 2; If required clamping force = 2917 N, clutch outer diameter = 400 mm, clutch inner diameter = 160 mm, what is the transmitted power?
Assume that you are to design a 3V V-belt drive. Given that input speed as 1750 rpm and nominal output speed as 725 rpm. Starting with belt linear velocity 4000 ft/min, specify the input sheeve D1 from the list above. D1 = ___ in. Provide write down steps including equations. *** 8.73 and 8.9 were marked incorrect
FINAL QUIZ IN PME 412 MACHINE DESIGN 1 PROBLEM: FOR HIBISCUS AND ROSE GROUPS 1. A helical spring must be capable of exerting a force of 600 N after being released 10 mm from its most highly compressed position. Wire of 6 mm diameter is used; the spring index is equal to 6. The loading is static. The maximum stress is 400 MPa. Find the required number of active coils.
An electric motor running at 970rpm is used to drive a rock crushing machine with a design power of 32 kW. A 33oz ducking weight flat belt drive is proposed with a tension ratio of R = 4 and belt width b = 120 mm. The pitch diameter of the driving pulley (on the motor-end) is 320mm. a) What is the mass per mm width per m length per ply in kg/mm/m/ply? Number (exact value) b) What is the maximum working tension per mm width per ply in N/mm/ply? Number (exact value) c) Calculate the belt velocity in m/s Number (+/-1%) d) Determine the number of belt plies required. Your answer should be an integer number (no decimals). Number (exact value)
QUESTION 6 Select the type of this mechanism below: L2 02 L3 А L1 C L4 O Crank-rocker O Triple rocker O Crank-crank O Slider-crank
Shift weight A so the lever would balance at 7/8 of the total length of the board measured from left to right. Datum -80 in 80 in A=100 Ibs B=100 Ibs C=100 Ibs
Question 4 On the front side of an ICE, a belt drive is used to transmit power from crank shaft pulley to an air- conditioning compressor pulley through an open type flat belt drive, as shown in Figure 3 below. The crank shaft pulley (driver) has a diameter of 15-cm and the compressor pulley (driven) is double from it. The center-to-center distance is 70-cm. At the front-end pulley, the tight tension is 700-N, angular velocity w, is 5500TT-rad/min, coefficient of friction is 0.40 and the weight per unit length is 4-N/m. By using all the information given, a) Show the center-to-center distance ideal? State your reason. b) Calculate the Angle of contact/wrap for both pulleys, e1 & 02 c) Predict the Slack tension, T2 d) Torque on both pulleys, T1 & T2 Driven T1 Driver T2 Figure 3
Q2 / A shaft transmitting 15kW at 200r.p.m. are supported by two bearings placed 1 m apart. A 600 mm diameter pulley is mounted at a distance of 300 mm to the right of left hand bearing and this drives a pulley directly below it with the help of belt having maximum tension of 2.25kN. Another pulley 400 mm diameter is placed 200 mm to the left of right hand bearing and is driven with the help of electric motor and belt having maximum tension of 3.376kN, which is placed horizontally to the right. The angle of contact for both the pulleys is180° and =0.24. Determine the suitable diameter for a solid shaft if the bending moment acting on the shaft is reversed, allowing working stress of 42MPA in shear for the material of shaft and have yield stress of 400MPA and ultimate stress of 500MP.. And design the keys which support each pulley if the material of the keys is the same for the material of shaft.
Design the elliptical cross-section of a belt pulley arm near the hub for the following specifications: The mean pulley diameter is 300 mm and the number of pulley arms are 4. The elliptical section has major axis twice the minor axis length. The tight and slack sides tension in the belt are 600 N and 200 N respectively. Assume half number of arms transmit torque at any time and the load factor of 1.75 to account for dynamic effects on the pulley while transmitting torque. The permissible tensile stress for cast iron pulley material is 15 MPa. The pulley hub diameter is 60 mm.